1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. CDX-MP80
  6. Service manual

Sony CDX-MP80 Service Manual

Fm/am & fm/mw/lw compact disc player
Hide thumbs Also See for CDX-MP80:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
Ver 1.0 2003. 01
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
95 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 107.9 MHz (US, Canadian Model)
87.5 – 108.0 MHz (AEP, UK Model)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (US, Canadian Model)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
MW/LW (AEP, UK Model)
Tuning range
MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW : 30 µV
LW : 40 µV
Sony Corporation
9-874-286-01
2003A0400-1
e Vehicle Company
© 2003. 01
Published by Sony Engineering Corporation
CDX-MP80
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Power amplifier section
Outputs
Speaker impedance
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Tone controls
Loudness
FM/AM COMPACT DISC PLAYER
FM/MW/LW COMPACT DISC PLAYER
US Model
Canadian Model
AEP Model
UK Model
CDX-MP70
MG-550M-156
DAX-23E
Speaker outputs
(sure seal connectors)
4 – 8 ohms
Audio outputs (front/rear)
Subwoofer output (mono)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input terminal
AUX IN terminal
Remote controller input terminal
Antenna input terminal
Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
+8 dB at 100 Hz
+2 dB at 10 kHz
– Continued on next page –
US, Canadian Model
AEP, UK Model
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-MP80

Summary of Contents for Sony CDX-MP80

  • Page 1 External aerial connector US, Canadian Model Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW : 30 µV LW : 40 µV FM/MW/LW COMPACT DISC PLAYER AEP, UK Model Sony Corporation 9-874-286-01 2003A0400-1 e Vehicle Company © 2003. 01 Published by Sony Engineering Corporation...
  • Page 2 NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Table Of Contents

    CDX-MP80 Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable TABLE OF CONTENTS CDs) This unit can play the following discs: 1. GENERAL Location of Controls (US, Canadian Model) ......4 Type of discs Label on the disc Location of Controls (AEP, UK Model) ........4 Connections (US, Canadian Model) ........

  • Page 4: General

    CDX-MP80 SECTION 1 GENERAL This section is extracted from instruction manual. (US, Canadian Model) (AEP, UK Model)

  • Page 5: Connections (Us, Canadian Model)

    CDX-MP80 Connections (US, Canadian Model)

  • Page 6: Connections (Aep, Uk Model)

    CDX-MP80 Connections (AEP, UK Model)

  • Page 7: Disassembly

    CDX-MP80 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-1. PANEL BASE ASSY 2-7. MECHANISM BLOCK (M) ASSY (Page 7) (Page 10) 2-8. TRAY (UM) ASSY 2-2. SUB PANEL (CD) (Page 11) (Page 8) 2-9.

  • Page 8: Sub Panel (Cd)

    CDX-MP80 2-2. SUB PANEL (CD) 1 PTT 2.6x6 2 bracket (cover) 4 PTT 2.6x6 7 claw 6 claw 5 PTT 2.6x6 3 PTT 2.6x6 8 sub panel (CD) (Take care not to pull the flexible board excessively) 2-3. CD MECHANISM BLOCK 4 CD mechanism block 2 PTT 2.6x6...

  • Page 9: Cam Block Assy, Motor Block Assy

    CDX-MP80 2-4. CAM BLOCK ASSY, MOTOR BLOCK ASSY 4 PTT 2.6x6 5 cover (protection) 1 PTT 2.6x6 6 motor block assy 2 cam block assy 3 CN602 2-5. MAIN BOARD 5 MAIN board 4 PTT 2.6x6 ground point 3 PTT 2.6x6 ground point 2 PTT 2.6x6...

  • Page 10: Heat Sink

    CDX-MP80 2-6. HEAT SINK 7 heat sink 6 PTT 2.6x6 5 PTT 2.6x10 1 PTT 2.6x6 4 cord (SUB OUT,AUX IN) 2 cord (ANTENNA) 3 PTT 2.6x6 2-7. MECHANISM BLOCK (M) ASSY 2 bracket (tray) 1 PTT 2.6x4 shaft chassis (ML) assy...

  • Page 11: Tray (Um) Assy

    CDX-MP80 2-8. TRAY (UM) ASSY 1 screw ( M1.7x2.5) 2 screw ( M1.7x2.5) 5 tray (UM) assy 3 screw ( M1.7x2.5) 2-9. MD ASSY 4 insulator 7 CN1 5 insulator 8 MD assy 2 CN2 6 insulator 1 CN3...

  • Page 12: Servo Board

    CDX-MP80 2-10. SERVO BOARD 4 toothed lock screw (M 2x3.5) 6 SERVO board 7 CN4 3 CN6 2-11. OPTICAL PICK-UP BLOCK 1 B 1.7x5 2 turntable motor assy (M1) chassis 5 sled motor assy (M2) 8 shaft retainer 6 gear (B) 7 P 1.4x3.5...

  • Page 13: Phase Alignment

    CDX-MP80 SECTION 3 PHASE ALIGNMENT 3-1. GEAR (CAM L) • Align the gear (cam L) position setting hole with the center mark on the bracket before screwing the motor block assy to the mechanism chassis. gear (cam L) position setting hole...

  • Page 14: Diagrams

    CDX-MP80 SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC5 CXD9684R-004 (AUDIO INTERFACE) (SERVO BOARD) Pin No. Pin Name Pin Description RESET Reset input MIMD CPU interface mode select signal input Connecting to +3.3 V in this set. CPU interface chip select signal input...
  • Page 15 CDX-MP80 Pin No. Pin Name Pin Description VDD (2.5V) — Power supply pin (+2.5 V) Data input 5 Boot control signal input SPDIF signal input VSSP — Ground pin PLL phase detect signal output VCOI VCO control voltage input VDDP —...
  • Page 16 CDX-MP80 • IC11 HD6432238RWN31TEIV (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description TEST Test mode select signal input DEC XRST DEC reset output DEC STBY DEC standby mode control signal output XRDE DRAM data read-out enable signal output Not used.
  • Page 17 Not used. (Open) LINK OFF Link off signal output EJECT KEY Eject key signal input UNI SO SONY bus serial data output UNI SI SONY bus serial data input UNI CK SONY bus clock signal input Not used. (Open) I2C interface data input/output...
  • Page 18 BUS ON control signal output BEEP Beep signal output TEL ATT Telephone mute detect signal input UNI SI SONY BUS data input UNI SO SONY BUS data output UNI CLK SONY BUS clock output 20 – 23 Not used. (Open)
  • Page 19 CDX-MP80 Pin No. Pin Name Pin Description Not used. (Open) FSW IN Oscillation frequency count input 66 – 68 Not used. (Open) FLASH W Flash write-in mode detect signal input I2C SDA I2C serial data output I2C SCL I2C serial clock output...
  • Page 20 CDX-MP80 • IC702 HD6432398-A02FWV (DISPLAY CONTROL) (MAIN BOARD) Pin No. Pin Name Pin Description SA CLK Spectrum analyzer clock output Not used. (Open) — Ground pin — Not used. (Open) — Power supply pin (+5 V) 6 – 9 Not used. (Open) —...
  • Page 21 CDX-MP80 Pin No. Pin Name Pin Description UNI SI Bus data input — Ground pin — Ground pin UNI CKI Bus clock signal input Not used. (Open) AVCC — Power supply pin (+5 V) VREF — Reference voltage pin (+5 V) 105 –...

  • Page 22: Block Diagram -Cd Section

    CDX-MP80 4-2. BLOCK DIAGRAM — CD SECTION — DIGITAL SERVO RF AMP DIGITAL SIGNAL PROCESSOR RFAC LOUT1 RFAC SIGNAL L CH PROCESSOR LOUT2 R CH AUDIO, AUDIO INTERFACE IC3 (1/2) A ATT DISPLAY RFDC RFDC EJECTKEY RFDC SECTION (Page 23)

  • Page 23: Block Diagram -Audio, Display Section

    CDX-MP80 4-3. BLOCK DIAGRAM — AUDIO, DISPLAY SECTION — CN303 AUX IN R-CH ELECTRONIC VOLUME IC305 CN301 CN302-1,-2 SUB OUT MUTE (MOMO) AUDIO AUX-L OUT SW Q305 R-CH IC310 TUNER UNIT TUX201 MD-L A OUT L ADSO AC IN L...

  • Page 24: Block Diagram -Bus Control, Power Section

    CDX-MP80 4-4. BLOCK DIAGRAM — BUS CONTROL, POWER SECTION — SYSTEM CONTROL CN101 (2/2) IC501 (2/2) Q411 TEL MUTE TEL MUTE TEL ATT DETECT CD ON IN Q406 CD ON ILLUMI ILL IN DETECT MOTOR MOTOR+ Q407 T-CLOSE TEST DRIVE...

  • Page 25: Circuit Boards Location

    CDX-MP80 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) SERVO board for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

  • Page 26: Printed Wiring Board -Cd Mechanism Section

    CDX-MP80 4-6. PRINTED WIRING BOARD — CD MECHANISM SECTION — • Refer to page 25 for Circuit Boards Location. • Semiconductor Location Ref. No. Location G-10 TP86 IC10 IC11 IC13 IC14 G-10...
  • Page 27 CDX-MP80 • Semiconductor (Page 30) Location Ref. No. Location F-10 IC12 IC15...

  • Page 28: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-MP80 • Refer to page 25 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 38 for IC Block Diagrams. IC B/D C107 C108 C109 C110 TP105 R157 R118 R162 R158 TP14 TP27 IC B/D...

  • Page 29: Schematic Diagram -Cd Mechanism Section (2/2)

    CDX-MP80 • Refer to page 25 for Waveform. 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 38 for IC Block Diagrams. (Page 28) IC12 IC B/D R130 TP17 R129 R119 R152 TP39 IC B/D C114...

  • Page 30: Printed Wiring Boards -Main Section

    CDX-MP80 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 25 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location D104 Q110 D107 E-10 Q111 D109 F-10 Q112 Q116 E-10 D150 D151 E-10...
  • Page 31 CDX-MP80 US,Canadian Model CN302 J651 CN101 C323 F901 CN601 R329 TUX201 IC309 C313 CN201 R601 CN301 CN304 TH101 R607 CN303 C319 D501 AEP,UK Model C397 R342 R409 C202 R404 C354 CN305 D601 C361 R401 FB301 FB303 C352 L401 R411 R222...

  • Page 32: Schematic Diagram -Main Section (1/4)

    CDX-MP80 • Refer to page 25 for Waveform. 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 41 for IC Block Diagrams. C303 R308 R309 C304 R310 R307 R388 R389 C306 R313 C307 R316 CN303 C393 FB303...

  • Page 33: Schematic Diagram -Main Section (2/4)

    CDX-MP80 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 43 for IC Block Diagram. Note: • Voltage is dc with respect to ground under no-signal R301 (detuned) condition. no mark : FM R302 C301 IC B/D...

  • Page 34: Schematic Diagram -Main Section (3/4)

    CDX-MP80 • Refer to page 25 for Waveforms. 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 42 for IC Block Diagrams. (Page 32) IC401 D409 L400 C410 C414 C411 R561 Q530 R539 CN401 IC411 R521 C419...

  • Page 35: Schematic Diagram -Main Section (4/4)

    CDX-MP80 • Refer to page 25 for Waveform. 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 43 for IC Block Diagram. (Page 33) L701 L100 C515 R101 C101 R102 Q101 Q102 R103 C709 R716 R104 R709...

  • Page 36: Printed Wiring Board -Display Section

    CDX-MP80 4-14. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 25 for Circuit Boards Location. LSW905 LSW902 LSW907 LED918 S903 LED907 LED904 LED901 LED911 S901 S904 LCD901 LED902 LED906 LED913 LED919 S902 LED908 LED905 LSW909 LED912 LED909...

  • Page 37: Schematic Diagram -Display Section

    CDX-MP80 • Refer to page 25 for Waveform. 4-15. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 42 for IC Block Diagram. ENC902(1/2) ENC901(1/2) IC B/D C906 IC902 LED900 IC903 R904 C905 C911 FB902 R910 C910 C908 R903...

  • Page 38: Ic Block Diagrams

    CDX-MP80 4-16. IC BLOCK DIAGRAMS IC1 CXD3027R (SERVO Board) IC2 CXA2581N-T4 (SERVO Board) IC3 NJM12902V-TE2 (SERVO Board) 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91...
  • Page 39 CDX-MP80 IC8 BH6518FS (SERVO Board) CHARGEPUMP CAPA- & CAPA+ IN4R FRDR INTERFACE INTERFACE IN4F FFDR OUT4F OUT2F PGND4 PGND2 OUT4R OUT2R VM34 VM12 OUT3R OUT1R PGND3 PGND1 OUT3F OUT1F IN3F TFDR INTERFACE INTERFACE IN3R TRDR IC6 MSM51V17400D-10TK-FS (SERVO Board) ON CHIP...
  • Page 40 CDX-MP80 IC5 CXD9684R-004 (SERVO Board) TIMING PROG. GENERAL GENERATOR /RESET START INPUT PORT MIMD I-BUS PROM INSTRUCTION 4kx2+2k DECODER =10kWORD 40bit PRAM 256WORD AD15 PROGRAM CONTROL MIDIO AD16 (I2C SDA) XRAM 4k WORD MICK (I2C SCL) YRAM 4k WORD AD14 CROM VDDT(3.3V)
  • Page 41 CDX-MP80 IC4 UT61L1024LC-12 (SERVO Board) CONTROL DECODER CORE ARRAY DATA I/O IC202 SAA6588T/V2-518 (MAIN Board) POWER SUPPLY PAUSE & RESET DETECTOR MULTI PATH 57kHz DETECTOR 8th ORDER BAND-PASS FILTER CLOCKED SIGNAL QUALITY COMPARATOR DECODER CLOCK CLOCK RDS/RDBS RDS/RDBS INTERFACE DATA...
  • Page 42 CDX-MP80 IC305 TDA7406 (MAIN Board) 32 31 30 29 28 27 26 25 MIXER SOFT STEP SOFT STEP SOFT STEP MONO FADER FADER FADER FADER CREF SUPPLY SACLK WOOFER FILTER OUTPUT SELECTOR DGND SWIN ACINR 17 SM ACOUTR SWACOUT C-BUS QUAL.
  • Page 43 CDX-MP80 IC601 BA8270F (MAIN Board) IC101 TL1451ACDB (MAIN Board) BUS ON BUS ON SWITCH VERF. +2.5V RESET RESET – SWITCH BUS ON REFERENCE CLK IN VOLTAGE ERROR BATTERY BATT BU IN COMPA- AMP2 SWITCH RATOR2 +2.5V VERF OUTPUT2 SHORT CIRCUIT...

  • Page 44: Exploded Views

    CDX-MP80 SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.

  • Page 45: Cam Section

    CDX-MP80 5-2. CAM SECTION M601 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3340-310-A SWITCH BOARD, COMPLETE 3-236-947-01 GEAR (CAM L) 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 3-237-005-01 GEAR (C) X-3381-368-1 BRACKET (SUB L) (RIVETING) ASSY...

  • Page 46: Main Board Section

    CDX-MP80 5-3. MAIN BOARD SECTION TUX201 F901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3381-657-2 CHASSIS (CD.S) ASSY * 111 3-019-565-01 BRACKET (IC) 3-230-417-11 SHEET, INSULATING 3-230-510-11 HEAT SINK 3-230-493-01 GEAR (DRIVE SHAFT) 1-777-246-41 CORD (WITH CONNECTOR) (ANTENNA)

  • Page 47: Front Panel Section

    CDX-MP80 5-4. FRONT PANEL SECTION not supplied (KEY board) LCD901 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3381-583-2 KNOB (VOL) ASSY X-3381-407-1 CASE ASSY (for FRONT PANEL) X-3383-173-1 PANEL (S) ASSY, FRONT (AEP,UK)

  • Page 48: Cd Mechanism Section (1)

    CDX-MP80 5-5. CD MECHANISM SECTION (1) (MG-550M-156) CDM-3123EBA Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-378-434-01 CUSHION, SARANET 3-243-340-01 CUSHION (PWB) 3-235-473-01 INSULATOR A-3340-216-A SERVO BOARD, COMPLETE X-3381-023-3 TRAY (UM) ASSY 4-628-646-11 SCREW (M2X3.5), TOOTHED LOCK (+) P 2-134-636-31 SCREW (M1.7X2.5)

  • Page 49: Cd Mechanism Section (2)

    CDX-MP80 5-6. CD MECHANISM SECTION (2) (MG-550M-156) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3381-055-4 PANEL (S) ASSY 3-234-326-01 RACK (SUB M) 2-626-869-11 SCREW (M2X3), SERRATION 3-234-352-02 CHASSIS (MR) X-3381-029-2 CHASSIS (ML) ASSY...

  • Page 50: Cd Mechanism Section (3)

    CDX-MP80 5-7. CD MECHANISM SECTION (3) (MG-550M-156) not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-234-340-01 GEAR (4) 4-639-357-21 SCREW (M1.7) 3-234-339-01 GEAR (5) 3-241-004-02 CUSHION (FPC), SARANET 3-234-330-01 GEAR (6) 3-236-897-01 SCREW (+P M1.4 MECH)

  • Page 51: Cd Mechanism Deck Section

    CDX-MP80 5-8. CD MECHANISM DECK SECTION (CDM-3123EBA) The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce...

  • Page 52: Electrical Parts List

    CDX-MP80 SECTION 6 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 53 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW904 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (SEEK +) R957 1-216-027-00 METAL CHIP 1/10W LSW905 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (Z) R958 1-216-027-00 METAL CHIP 1/10W LSW907 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (SOURCE)
  • Page 54 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C110 1-164-217-11 CERAMIC CHIP 150PF C226 1-107-826-11 CERAMIC CHIP 0.1uF C111 1-115-156-11 CERAMIC CHIP (AEP,UK) C112 1-164-156-11 CERAMIC CHIP 0.1uF C227 1-162-966-11 CERAMIC CHIP 0.0022uF 10%...
  • Page 55 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C350 1-164-227-11 CERAMIC CHIP 0.022uF C421 1-107-826-11 CERAMIC CHIP 0.1uF C351 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C422 1-162-964-11 CERAMIC CHIP 0.001uF C352 1-124-721-85 ELECT 10uF C501 1-162-968-11 CERAMIC CHIP 0.0047uF 10%...
  • Page 56 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C708 1-162-964-11 CERAMIC CHIP 0.001uF D506 8-719-988-61 DIODE 1SS355TE-17 C709 1-164-156-11 CERAMIC CHIP 0.1uF D507 8-719-820-05 DIODE 1SS181 C710 1-162-964-11 CERAMIC CHIP 0.001uF D508 8-719-404-50 DIODE MA111-TX...
  • Page 57 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC701 8-759-277-63 IC TC7W14FU(TE12R) Q407 8-729-120-28 TRANSISTOR 2SC1623-L5L6 IC702 6-801-484-01 IC HD6432398A02FWV Q408 8-729-106-60 TRANSISTOR 2SB1115A Q409 8-729-027-46 TRANSISTOR DTC114YKA-T146 < JACK > Q410 8-729-022-51 TRANSISTOR XN1A311-TX...
  • Page 58 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R205 1-216-833-11 METAL CHIP 1/10W R338 1-216-813-11 METAL CHIP 1/10W (AEP,UK) R339 1-216-833-11 METAL CHIP 1/10W R206 1-216-825-11 METAL CHIP 2.2K 1/10W R340 1-216-833-11 METAL CHIP...
  • Page 59 CDX-MP80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R410 1-216-073-00 RES-CHIP 1/10W R544 1-216-853-11 METAL CHIP 470K 1/10W R411 1-216-057-00 METAL CHIP 2.2K 1/10W R545 1-216-845-11 METAL CHIP 100K 1/10W R413 1-216-841-11 METAL CHIP...
  • Page 60 CDX-MP80 MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R807 1-216-809-11 METAL CHIP 1/10W 1-107-826-11 CERAMIC CHIP 0.1uF R808 1-216-821-11 METAL CHIP 1/10W 1-162-968-11 CERAMIC CHIP 0.0047uF 10% R809 1-216-809-11 METAL CHIP 1/10W 1-162-968-11 CERAMIC CHIP 0.0047uF 10%...
  • Page 61 CDX-MP80 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C114 1-107-826-11 CERAMIC CHIP 0.1uF 1-414-398-11 INDUCTOR 10uH C121 1-115-156-11 CERAMIC CHIP 1-412-006-31 INDUCTOR 10uH C122 1-115-156-11 CERAMIC CHIP 1-414-398-11 INDUCTOR 10uH C123 1-115-156-11 CERAMIC CHIP...
  • Page 62 CDX-MP80 SERVO SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-827-11 METAL CHIP 3.3K 1/10W R123 1-216-833-11 METAL CHIP 1/10W 1-216-833-11 METAL CHIP 1/10W R124 1-216-845-11 METAL CHIP 100K 1/10W 1-216-853-11 METAL CHIP 470K 1/10W...
  • Page 63 CDX-MP80 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCELLANEOUS PARTS FOR INSTALLATION AND CONNECTIONS *************** *************************************** 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US,CND) 3-014-370-22 FRAME, FITTING 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) X-3366-405-1 SCREW ASSY (EXP), FITTING (AEP,UK)
  • Page 64 CDX-MP80 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

Table of Contents