Table of Contents
Advertisement
Quick Links
http://www.monomachines.com/
1400 Quick Setup Guide
UNPACKING
1. Inspect package for damage.
2. Remove 1400 from box and place on a solid level surface. Caution: Two people are required to
lift machine out of box, as it weighs 81 lbs.
3. Inspect packing to ensure all components are included.
4. Refer to the contact information on the last page if installation or service assistance is needed.
Components
1
1
1400
2
Catch Tray
3
Power Cord
Control Panel
1
"START" Button
2
"STOP" Button
3
"READY" Indicator
http://www.monomachines.com/
2
1
Press to start operation
Press to stop operation
Green indicates the FD 1400 is ready to operate / Blinking Red indicates a fault
1
For More Info
Click Here --->
4
Upper Fold Plate
5
Jam Clearing Bar
6
Lower Fold Plate (Ships installed)
3
2
3
4
5
6
Advertisement
Table of Contents
Related Manuals for Formax FD 1400
Summary of Contents for Formax FD 1400
-
Page 1: Control Panel
Jam Clearing Bar Power Cord Lower Fold Plate (Ships installed) Control Panel “START” Button Press to start operation “STOP” Button Press to stop operation “READY” Indicator Green indicates the FD 1400 is ready to operate / Blinking Red indicates a fault http://www.monomachines.com/... -
Page 2: Installation
http://www.monomachines.com/ For More Info INSTALLATION Click Here ---> 1. InFeed Tray Extension Lift infeed tray extension and lock into place 2. Lower Fold Plate Remove shipping bands from lower fold plate located under the infeed tray. 3. Upper Fold Plate Lift top cover and remove http://www.monomachines.com/... - Page 3 For More Info http://www.monomachines.com/ Top View Click Here ---> Top Cover Pins Fold Plate Fold Plate Pins Pins Side View Fold Plate Pin Top Cover Pins Fold Plate Pin Top Cover Pin a. Slide the upper fold plate under the top cover pins onto the fold plate pins. Push down on the fold plate to lock it into position.
-
Page 4: Fold Setup
For More Info http://www.monomachines.com/ FOLD SETUP Click Here ---> 1. Determine Fold types Two Standard Folds 11” “Z” & 11” “C” - Refer to Operator Manual for custom fold setup. Leading glue edge Glue Glue 11” “Z” Fold 11” “Z” Fold Leading glue edge Glue Glue... - Page 5 For More Info http://www.monomachines.com/ Click Here ---> 2. Setting Fold Plates Fold indicator decals Fold stop knobs Fold stop After determining the fold type of your pressure seal form you will need to set the fold plates. a. Top Fold Plate: Leave the top fold plate in position, loosen the fold stop knobs and slide the fold stop to the appropriate fold setting on the fold indicator decals and retighten the fold stop knobs.
- Page 6 http://www.monomachines.com/ For More Info 3. Setting Infeed Side Guides Click Here ---> Infeed Side guides a. Place a form between the side guides. Adjust the side guides by sliding them left or right so that the form is snug but still lies flat. Equal spacing between side frame and guides on both sides b.
-
Page 7: Operation
http://www.monomachines.com/ For More Info OPERATION Click Here ---> 1. Power Power switch Switch the power button, located under the infeed tray, to the on position. 2. Loading Forms Feed table lever a. Remove printed forms from the printer and square them so they are in a neat stack. b. -
Page 8: Troubleshooting
Depot Ship to Address: Formax 44 Venture Dr Dover NH 03820 *Machines cannot be shipped to Formax without an RMA#. Shipments will not be accepted without an authorized Formax RMA#. Assistance after the 90 Day Factory Direct Warranty Please contact Intrepid service company for onsite nationwide service. Intrepid of- fers annual service agreements for your FD 1400 and per trip service at their hourly rate. -
Page 9: Leading Edge
http://www.monomachines.com/ Leading Edge For More Info Click Here ---> Make copies of this page on copy paper for fine tuning folds Instruction For Lining Up Folds Instruction For Lining Up Folds 1. Place a stack of these sheets into the feeder and fold one (1) or two (2) sheets.