Subscribe to Our Youtube Channel
Related Manuals for ARKSCAN ES301
Summary of Contents for ARKSCAN ES301
- Page 1 Mini Wireless Barcode Reader Quick Guide Full user’s manual is available on the enclosed CD. Mini Wireless Barcode Reader Quick Guide (Rev5) P/N: 8002-0028*07...
- Page 2 FCC WARNING STATEMENT WARNING AND CAUTION This equipment has been tested and found to comply with the limits for a Class B digital 1. Take any metals into contact with the terminals in connectors. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 2.
-
Page 3: Specifications
OUT OF THE BOX INTRODUCTION Trigger LED Indicator Mini Wireless Mini USB port Barcode Reader (w/ Protective Cover) Exit Window SPECIFICATIONS Light source 625nm visible red LED Scan rate 240 scans/sec Sensor Linear CMOS sensor Quick Guide Quick Connection Card Resolution 5mil/ 0.127mm Housing... -
Page 4: Getting Started
BEEPER INDICATION GETTING STARTED Single long beep Power up Single beep Good read Single short beep The scanner reads a Code39 of ASCII in configuration procedure Two beeps i. Wireless connection ii. The scanner successfully reads a configuration barcode ... -
Page 5: Getting Connected
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ STEP 1 . E032$ [ Recommanded ] *.E043$* *.E032$* BT mode - HID Pincode Start 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] STEP 2 3. -
Page 6: Numeric Bar Codes
NUMERIC BARCODES - 9 - - 10 -... -
Page 7: Power Off Timeout
SMARTPHONE/TABLET CONNECTION POWER OFF TIMEOUT Getting Connected - iOS & Android The timeout of inactivity before auto power-off. Variable Timeout Simply follow instruction in [BT mode - HID] (page 7) ,in which step 5 can be skipped since iOS & Android will not require pin-code . -
Page 8: Interface Selection
INTERFACE SELECTION BATCH MODE . E054$ . C035$ *.c035$* WIRELESS ENABLE . C008$ . E053$ *.c008$* DISABLE USB-HID . C006$ In Batch Mode, data will be temporarily stored in memory buffer *.C006$* (2KB RAM) when the scanner is out of range or in poor connection USB-VCP quality. - Page 9 GENERAL SETTINGS READING MODE . A001$ . F002$ TRIGGER DEFAULT . P023$ . F003$ ABORT TOGGLE . A007$ . F001$ CHECK FLASH VERSION BEEPER . F005$ CONTINUOUS . F012$ BEEP OFF . F006$ CONTINUOUS . F018$ AUTO OFF BEEP ON - 15 - - 16 -...
- Page 10 KEYBOARD LAYOUT . C009$ . C010$ JAPAN ENGLISH (USA) (106 key) . C018$ . C025$ ENGLISH CANADIAN (UK) (FRENCH) . C034$ . C012$ CANADIAN FRENCH (TRADITIONAL) . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
- Page 11 KEYBOARD LAYOUT . C030$ . C017$ CZECH BELGIAN (QWERTY) (AZERTY) . C028$ . C022$ CZECH DUTCH (QWERTZ) . C027$ . C021$ HUNGARIAN DANISH (QWERTZ) . C024$ . C032$ HUNGARIAN SLOVAK (101 KEY) . C033$ . C016$ SWISS BRAZILIAN (GERMAN) (PORTUGUESE) .
-
Page 12: Gs1 Databar Expanded
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE CODE 93 ALL CODE . N017$ . K010$ CODE 32 IATA . L010$ . L014$ UK PLESSEY TELEPEN . L001$ . N032$ GS1 DATABAR . N010$ . N001$ INDUSTRIAL GS1 DATABAR 2 OF 5 LIMITED . -
Page 13: Check Version
TERMINATOR . D012$ The following pages only apply to the memory version mini wireless scanner. . D011$ The firmware version with suffix “MEM” . D013$ supports memory function. e.g. SM3-c-X.XX.BTA.MEM CR + LF The firmware version can be found either . -
Page 14: Memory Mode
MEMORY MODE OUTPUT DATA For memory version only For memory version only . R001$ . R003$ *.R001$* *.R003$* OUTPUT DATA ENABLE MEMORY You may output data ONLY when memory is enabled (page 15). . R002$ *.R002$* Data Output Method DISABLE MEMORY . -
Page 15: Data Format
DATA FORMAT DATE & TIME SETUP For memory version only For memory version only . R011$ . R006$ *.R011$* *.R006$* SET DATE DATA FORMAT The default Data Format is <Item No.>, <Date>, <Time>, <Barcode Data> Example: To set Date to 2012-08-01 (Year-Month-Day): below are items and their setup codes: 1. -
Page 16: Date Format
DATE FORMAT TIME FORMAT For memory version only For memory version only . R008$ . R009$ *.R008$* *.R009$* DATE FORMAT TIME FORMAT The default Date Format is DD/MM/YYYY (Code = 09), below The default Time Format is HH:MM:SS (Code = 01), below is full list of available formats and their setup codes: are available formats and their setup codes: Code... -
Page 17: Test Barcodes
TEST BARCODES Code 39 CODE-39 TEST Interleaved 2 of 5 9876543210 Code 128 12345678 - 31 -...
Need help?
Do you have a question about the ES301 and is the answer not in the manual?
Questions and answers