Harman Kardon AVR45 Service Manual page 7

Remote Control
AVR Selector : Press this button to use the Mute : Press this button to momentarily
remote control for operation of the AVR-65. Note silence the AVR-65 or TV set being controlled,
that the button will briefly turn red after it has depending on which device has been selected.
been pressed to confirm your selection.
Test :
Device Control Selectors : Press one of sequence used to calibrate the AVR-65's output
these button to use the remote to control the levels.
functions of another audio/video device. Note
that the button will briefly turn red after it has Display/Multiroom Button :
been pressed to confirm your selection. does not function with AVR-65, but it is available
for use with other devices.
Power Button : Press this button to turn the
currently selected device on or off.
buttons. They will be used most frequently to
select a surround mode.
To change the surround mode, first press the
SURR/CH button
buttons to scroll up or down through the list of
surround modes that appear in the Information
Display . These buttons are also used to
increase or decrease output levels used to lower
the AVR-65's output levels when configuring the
unit with either the internal test tone or and
external source. They are also used to enter
delay time settings after the
been pressed.
/ Channel Button :
to start the process of setting the AVR-65's
output levels to an external source. Once this
button is pressed, use the
select the channel being adjusted, then press
the Set button , followed by the
again to change the level setting.
Set Button : This button is used to enter
settings into the AVR-65's memory. It is also
used in the setup procedures for delay time,
speaker configuration and channel output level
adjustment.
Night Mode : Press this button to activate
the "Night" mode, preventing loud playback
when the digital modes are in use without
altering the dynamic range of the output signal.
When the AVR-65 remote is being programmed
to operate other devices, this button is pressed
to begin a readout of a programmed code.
Press this button to begin the Source Selectors :
select an input source for the AVR-65. The AM/
FM button is also used to switch between
frequency bands when the tuner in use.
This button
NOTE : Pressing one of these buttons selects
the source only. In order to control the actual
source machine using the remote you must
Buttons : These are multi purpose press the Press Control Selector
the desired product.
Numeric Keys : These buttons serve as a
ten-button numeric key-pad to enter tuner preset
. Next press these positions. They are also to be used to select
channel numbers when TV has been selected
on the remote, or to select track numbers on a
CD, DVD or LD player, depending on how the
remote has been programmed.
NOTE : The 0 button has a dual function. It also
serves as the CLEAR button for use in
Delay button has programming the tuner or clearing the system
memory.
This button is used Direct/Enter : Press this button to select a
radio station by entering its frequency using the
Numeric Key .
/ buttons to
Memory Button : Press this button to enter
/ buttons a radio station into the AVR-65's preset memory.
After pressing the button the
will flash, and you then have five seconds to
enter a present memory location using the
Numeric Keys .
NOTE : Although the word "Sleep" appears
above this button, it refers to control of devices
other than the AVR-65. Use the
to control the AVR-65's Sleep function.
OSD Button : This button dose on screen
display function with the AVR-65.
Semi Full OFF
Light Button : Press this button to activate
the remote's built-in back-light for better legibility
of the buttons in a darkened room.
Press these buttons to
Tuner Mode : Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so that the AUTO
pressing the Tuning buttons
frequency up or down in single-step increments.
When the FM band is in use, pressing this button
button for when a station's signal is weak will change to
monaural reception, as indicated by the
7
indicator .
Clear Button : This button dose not
function with the AVR-65, but it is available for
use with other devices.
Press Up/Down : When the tuner is in use,
these buttons scroll through the stations that
have been programmed into the AVR-65's
memory, When many source devices, such as
CD players, VCRs and cassette decks, are
selected using the Device Control Selectors
these buttons will normally function as chapter
step or track advance.
Tuning Up/Down : When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the Tuner Mode
button has been pressed so that the
MEMORY indicator indicator is illuminated, pressing these
buttons will cause the tuner to seek the next
station with acceptable signal strength for quality
reception. When the AUTO indicator
illuminated, pressing these buttons will tune
stations in single-step increments.
Sleep button Transport Control : These controls do not
control any function of the AVR-65, but they are
used extensively when operating a wide variety
of CD players, cassette decks and VCRs.
Delay/Prev Ch. : Press this button to begin
the process for setting the delay times used by
the AVR-65 when processing surround sound.
After pressing this button the delay times are
entered by pressing the Set button
using / buttons to change the setting.
Press the Set button again to complete the
process.
indicator goes out, / Digital Button : This button is used to
will move the select the type of digital input used with any one
of the input sources connected to the AVR-65.
After pressing this button, use the /
(7) to make your selection between OPTICA
MONO or COAXIAL digital. Press the Set button
to enter your choice.
Speaker Configuration : Press this button
to begin the process of configuring the AVR-65's
Bass Management System for use with the type
of speaker used in your system.
Once the button has been pressed, use the /
buttons to select the channel you wish to set
up. Press the Set button , and then select
another channel to configure. When all
adjustments have been completed, press the Set
. button twice to exit the settings and return to
normal operation.
Surround Mode Selector : Press this
button to begin the process of changing the
surround mode. After the button has been
pressed, use the / buttons to select the
AUTO desired surround mode. Note that this button is
also used in the "Auto Search" process.
Volume : Press these buttons to raise or
is NOT lower the system volume.
Sleep Button : Press this button to place
the unit in the Sleep Mode. After the time shown
in the display, the AVR-65 will automatically go
into the standby mode. Each press of the button
changes the time until turn-off in the following
order:
90 80 70 60 50 40
30 20 10 5 1 OFF
, and then
Note that this button is also used to change
channels on your TV when the TV is selected
using the Devise Control Selector .
When the AVR-65 remote is being programmed
for the codes of another device, this button is
also used in the "Auto Search" process.
buttons