Page 1
INTRODUCTION Parts Check List: To purchase replacement battery packs, 1. Handset call VTECH Communications at 1-800-595- 2. Base Unit 9511. In Canada, call VTECH Electronics 3. Telephone Line Cord at 1-800-267-7377. 4. Battery Pack 5. AC Adapter...
Never spill liquid of any kind on the product. 10.To reduce the risk of electric shock, do not disassemble this product. If service or repair work is required, contact VTech Customer Service at 1-800-595-9511. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks.
VTech product service centers. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery recycling and disposal bans / restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
2. Plug the AC power adapter into an electrical outlet and the DC connector to the power jack on the bottom of the Base Unit. Insert the cord in the channel guide. CAUTION: Use only the AC adapter shipped with your VT9113. It is specifically designed for this product.
HANDSET FEATURES ON LED • The ON LED lights when the Handset is on an active call. • It flashes in cadence with an incoming ring. • It flashes quickly during Programming mode. • It flashes slowly when the battery pack is low. ON/ FLASH KEY •...
TONE dialing. If you have rotary service, press MEM/PROG, * , # , MEM to switch to PULSE. NOTE: Your VT9113 is preset at the factory for TONE dialing. Temporary Tone If you have a rotary (dial-pulse) telephone service, (TONE/PULSE setting is set to PULSE), this feature allows you to enter special codes and tones to operate answering machines, use electronic banking services, calling cards, or other special services.
Page 7
Press the MEM key to confirm Memory Dialing The VT9113 can store up to 10 different phone numbers that you can dial just by pressing ON, MEM and one of the number keys (0-9). Note: if the dialing method is pulse, the digit <#> will be ignored, and the digit <*> will initial temporary DTMF dialing.
If you still have difficulty after trying these suggestions, In the US Call: VTECH Communications at 1-800-595-9511. In Canada Call: VTECH Electronics at 1-800-267-7377. THE PHONE DOESN'T WORK AT ALL. • Make sure the power cord is plugged in. •...
Page 9
IN CASE OF DIFFICULTY YOU HEAR NOISE IN THE HANDSET, AND NONE OF THE KEYS OR BUTTONS WORK. • Make sure the power cord is plugged in. • Your Base Unit and Handset may not be operating on the same channel or security code.
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTECH electrical accessories; or 5. Product whose warranty/quality stickers, Product serial numbers plates or electronic serial numbers have been removed, altered or rendered illegible;...
Page 11
If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTECH will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
MAINTENANCE Your VT 9113 cordless telephone contains sophisticated electronic parts so it must be treated with care. Avoid rough treatment Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it. Avoid Water Your telephone can be damaged if it gets wet.
This equipment is compatible with inductively coupled hearing aids. Should you experience trouble with this telephone equipment, please contact: VTech Communications Inc CUSTOMER SERVICE at 1-800-595-9511. In Canada, call VTech Electronics Ltd. at 1- 800-267-7377. For repair/warranty information. The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected.
Page 14
FCC, ACTA and IC REGULATIONS equipment approved prior to July 23, 2001, the product identifier is preceded by the phrase “FCC Reg No.” and the REN is listed separately. For equipment approved after that date, the product identifier is preceded by “US” and a colon (:), and the REN is encoded in the product identifier without a decimal point as the sixth and seventh characters following the colon.
Page 15
Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. Your VT9113 is designed to operate at the maximum power allowed by the FCC and IC. This means your Handset and Base Unit can communicate only over a certain distance - which will depend on the location of the Base Unit and Handset, weather, and the construction and layout of your home or office.
Need help?
Do you have a question about the VT9113 and is the answer not in the manual?
Questions and answers