Page 2
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF YOU ARE ASSEMBLING THIS UNIT FOR SOMEONE ELSE, GIVE THIS MANUAL TO HIM OR HER TO SAVE FOR FUTURE REFERENCE. FOR CUSTOMER SERVICE, PLEASE CALL 1-877-630-5396 (TOLL-FREE), MONDAY THROUGH FRIDAY FROM 10:00 AM TO 7:00 PM (EST). DO NOT RETURN TO PLACE OF PURCHASE.
Page 3
1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity within 7 .62 m/25 ft of this or any other appliance. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment.
GRILL OPERATION 1-2-3 Before grilling: 1. Keep your grill a safe distance away from your property.* 2. Always perform a leak-test on all connections and hoses.* 3. Keep children away from the grill. During grilling: To avoid tripping safety valves, please follow these instructions carefully! 1.
SAFETY INSTRUCTIONS Always read and understand the WARNINGS and INSTRUCTIONS that are contained in this manual before attempting to use this gas barbecue grill, to prevent possible bodily injury or property damage. Always keep this manual for convenient future reference. TA B L E O F CO N T E N TS SECTION ONE Safet y instructions .................6...
S EC T I O N O N E SAFETY INSTRUCTIONS NOTE: The use and installation of this product must conform to local codes. In the absence of local codes, use the National Fuel Gas Code, ANSI Z223.1/NFPA54. Reference to Natural Gas and Propane Installation code CSA B149.1 or Propane Storage and Handling code B149.2 IMPORTANT NOTICE: READ ALL INSTRUCTIONS...
Page 7
3. Always open the grill lid carefully and slowly as heat and steam trapped within the grill could cause severe burns. 4. Always place your grill on a hard and level surface far away from combustible materials and structures. An asphalt or blacktop surface may not be acceptable for this purpose.
Page 8
14. Do not attempt to move the grill while it is lit. 15. Do not use the grill unless it is COMPLETELY assembled and all parts are securely fastened and tightened. 16. Keep combustible items and surfaces at least 60.96 cm/24" away from the grill at all times. DO NOT use this gas grill or any gas product under any overhead enclosure or near any unprotected combustible constructions.
Page 9
3. Clean and inspect the hose before each use. If there is evidence of abrasion, wear, cuts or leaks, the hose must be replaced prior to operation. The replacement hose assembly should be in accordance with the manufacturer’s specifications. 4. Move gas hoses as far away as possible from hot surfaces and dripping hot grease.
Page 10
2. Always confirm that this grill is not positioned under the overhang of a house, a garage or other structure before lighting it. An overhang will serve to deflect flare-ups and radiated heat into the structure itself, which could result in a fire. 3.
Page 11
or in the vicinity of any other heating-generating appliance, because of the danger of starting a fire. 9. Always confirm that the installation of this grill conforms with the requirements of all local codes or, in the absence of applicable local codes, with either the National Fuel Gas Code, ANSI Z223.NFPA 54 or CAN/CGA-B149.2.
• Inspect the grill before each use. 1. Inspect all hoses and connections and make certain they are secure. 2. Check and clean the burner venturi tubes for spiders and insect nests by removing the burner and inserting a bottle brush cleaner into each tube to make sure the passage is clear.
S EC T I O N T WO PARTS LIST / DESCRIPTION 1. bottom panel assembly, 14. right side shelf, 1 pc 1 pc 15. side burner knob, 1 pc 2. left side panel, 1 pc 16. side knob seat, 1 pc 3.
Page 14
HARDWARE LIST A. bolt (M6x20), 4 pcs B. bolt (M6x15), 23 pcs C. bolt (M4x15), 20 pcs D. bolt (M4x10), 2 pcs E. flat washer (M6), 22 pcs F. spring washer (M6), 22 pcs G. flat washer (M4), 22 pcs H.
ASSEMBLY INSTRUCTIONS STEP 1 Remove all contents from the carton packaging. Make sure all parts are present before attempting assembly. Once the grill is fully assembled, go back and check to make certain all the bolts are secure. Tighten again using the screwdriver provided if necessar y.
Page 16
STEP 2 a) Loosen the four bolts pre-installed on the left and right side panels and insert the back panel. Tighten by hand until secure. b) Align the holes on the back panel with the holes on the bottom panel assembly.
Page 17
STEP 4 a) Align the hole on the spare cylinder stopper with the hole on the left side panel as shown. b) Insert one bolt with one spring washer one flat washer into the pre-drilled hole. Tighten the bolt using the screwdriver provided.
Page 18
STEP 6 a) Place the front beam on the front of cart assembly. b) Align the holes on the front beam with the top and side holes on the frame of the right side panel. c) Insert one bolt with one spring washer and one flat washer into each hole.
Page 19
STEP 7 a) Insert the pin on the bottom of the left door into the hole on left side of the 1 1-1 (1) bottom panel assembly as shown. b) Insert the pin on the top of the left door into the hole on the left side of (9) 1 1-1 front beam.
Page 20
STEP 8 a) Place the body assembly on the top of cart assembly. Make certain the pre-drilled holes on the right side of body assembly are aligned properly with the holes on the right side of cart assembly. b) Insert one bolt with spring washer and one flat...
Page 21
STEP 10 a) Align the holes on the side knob seat with the holes on right side shelf and side burner valve. b) Insert one bolt with one flat washer into each pre-drilled hole. c) Tighten the bolts using the screwdriver provided. d) Insert the side burner knob onto the knob shaft...
Page 22
STEP 12 a) Open the left top lid first, and align the holes on motor support with the holes on the side panel of body assembly as shown. b) Insert one bolt from the inside of the motor support into each hole on the side panel of the body assembly.
Page 23
STEP 14 Slide the grease pan into the tracks on cart frame as shown. STEP 15 Connect the natural gas hose with the side burner valve by screwing the nut on end of the hose. gas supply gas inlet natural gas hose...
Page 24
STEP 16 a) Hook the grease cup supports into the holes on the grease pan as shown. grease cups onto the grease cup supports. b) Place the STEP 17 a) Insert the grease pan stopper into the hole on the back panel as shown. b) Tighten the stopper by hand.
Page 25
STEP 18 a) To fix the wire, clip on the side panel as shown. b) Insert the connector plugs into the hole on transformer. Tighten the plastic nut until secure. STEP 19 Fully assembled.
S EC T I O N T H R E E SAFETY CAUTION: Your natural gas grill has been designed to operate on natural gas only, at a pressure of seven inches water column (7" W.C /1.7Kpa). Check with your gas utility for local gas pressure, because in some areas natural gas pressure varies.
NATURAL GAS CONNECTION Connect a manual shut-off valve to gas supply line. Apply sealing compound or pipe thread tape of the t ype resistant to the action of natural gas on all male pipe threads. Attach to side burner valve. Connect the other end of the flex hose to manual shut-off valve through a nipple.
Page 28
WARNING: Burner valves are pre-tested at the factory to operate on natural gas. Do not attempt to convert or change. DANGER: To prevent fire or explosion hazard when testing for a leak: 1. Always perform the leak-test before lighting the grill and each time the natural gas hose is connected for use.
LEAK-TESTING BEFORE TESTING Make sure that all packaging material is removed from the grill including the burner tie-down straps. DO NOT SMOKE WHILE LEAK-TESTING. NEVER LEAK-TEST WITH AN OPEN FLAME. TO TEST 1. Make approx. 90 mL/3 fl oz of leak solution by mixing one part liquid dishwashing soap with three parts water.
S EC T I O N F O U R LIGHTING INSTRUCTIONS DANGER: Failure to open lid while igniting the grill’s burners or not waiting 5 minutes to allow gas to clear if the grill does not light, may result in an explosion, which could cause serious injury or death.
Page 31
5. After burner ignites, repeat the procedure with any other burner desired. 6. Adjust valve knob(s) to desired cooking temperature. Using the lighting stick to light the main burners 1. Insert a match into the end of lighting stick locked in the drawer.
Page 32
SIDE BURNER Instructions 1. Open lid while lighting the burner. Lid must remain open while burner is lit. 2. Valve must be in the OFF position. 3. Open natural gas valve. 4. Push and turn control knob slowly about ¼ turn counter-clockwise until a click is heard.
Page 33
Fig. A Fig. B Fig. C observe flame height when lit: Flame should be a blue/yellow colour, between 1 and 2 inches high (2.5-5 cm) INFRARED BURNER Lighting the infrared burner 1. Open lid while lighting burner. 2. Make sure the control knob is locked in the OFF position. 3.
WARNING: Always monitor the grill closely when cooking and turn the flame level down to LOW or OFF, if flare-ups intensify. SHUTTING OFF BURNERS 1. Always turn the valve knob(s) clockwise to the HIGH position, then press and turn to OFF. Never force the knob without pressing it. This could damage the valve.
8. Wait for at least 5 minutes. 9. Reconnect the natural gas hose. 10. Slowly turn the natural gas valve ¼ turn at a time and have the valve all the way open. 11. With the lid open: For grill with ignition button: ONLY turn on ONE front burner control knob to the HIGH position.
Page 36
DO NOT clean any grill part in a self-cleaning oven. The extreme heat will damage the finish. Burning off the grill after ever y use (approx. 15 minutes) will keep excessive food residue from building up. Recommended cleaning materials Mild dishwashing liquid detergent Hot water Nylon cleaning pad Wire brush...
Flame tamers Clean residue with wire brush and wash with soapy water. Rinse with water. Grease pan/Grease cups Periodically empt y the grease pan/grease cups and clean with a dishwashing detergent and hot water solution. Burner assembly 1. Turn gas off at the control knobs and natural gas valve. 2.
Page 38
PROBLEM POSSIBLE CAUSE SOLUTION Wires and/or electrode Clean wire and/or electrode Burner will not ignite covered with cooking with rubbing alcohol. using knobs or igniter. residue. Electrode and burners Wipe dry with cloth. are wet. Electrode cracked or Replace electrode. broken –...
Page 39
PROBLEM POSSIBLE CAUSE SOLUTION Sudden drop in gas flow Out of gas Call your local or reduced flame height. gas company. Excess flow safety device Refer to the ”Excess flow may have been activated. safety valve reset” procedure on page 34. Irregular flame pattern, Burner ports are clogged Clean burner ports.
Page 40
PROBLEM POSSIBLE CAUSE SOLUTION Excessive cooking Adjust (lower) temperature temperature. accordingly. Persistent grease fire. Grease trapped by food Turn knobs to OFF. build-up around burner system. Turn gas OFF at natural gas valve. Leave lid in closed position and let fire burn out. After grill cools, remove and clean all parts.
S EC T I O N S I X LIMITED WARRANTY WARRANTY PROGRAM: Proof of purchase is required to access this warrant y program, which is in effect from the date of purchase. If you are not able to provide proof of purchase before or after the warrant y has expired, you will be subject to parts, shipping and handling fees.
Page 42
Some provinces do not allow the limitation or exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warrant y gives you specific legal rights, and you may also have other rights that vary from province to province. If you have any questions related to the product or warrant y, please call customer service at 1-877-630-5396, Monday through Friday from 10:00 AM to 7:00 PM (EST).
Need help?
Do you have a question about the PC25774 and is the answer not in the manual?
Questions and answers