Table of Contents
Advertisement
4-3. CIRCUIT BOARDS LOCATION
4-3-1. DISPLAY UNIT (PDM-6100)
G2 Board
G1 Board
F1 Board
K2 Board
K3 Board
R1 Board
4-3-2. MEDIA RECEIVER UNIT (MBT-MR1)
AU Board
A Board
H4 Board
H1 Board
H2 Board
R2 Board
P Board
U2 Board
AD Board
IFA Board
U1 Board
M Board
MS2 Board
H3 Board
4-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
Note:
All capacitors are in µF unless otherwise noted. (pF: µµF)
•
Capacitors without voltage indication are all 50 V.
•
Indication of resistance, which does not have one for rating electrical
power, is as follows.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
•
All resistors are in ohms.
•
: nonflammable resistor.
•
: fusible resistor.
•
: internal component.
•
: panel designation, and adjustment for repair.
•
All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
•
: earth-ground.
•
: earth-chassis.
•
#
: not mounted.
•
When replacing the part in below table, be sure to perform the related
adjustment.
•
All voltages are in V.
•
Readings are taken with a 10 MΩ digital multimeter.
•
Readings are taken with a color-bar signal input.
•
Voltage variations may be noted due to normal production tolerances.
•
: Can not be measured.
*
•
Circled numbers are waveform references.
•
: B + bus.
•
: B – bus.
•
: Signal path.
Note: The components identified by shading and
mark ! are critical for safety. Replace only
with part number specified.
Note: Les composants identifiés par un tramé et
une marque ! sont critiques pour la
sécurité. Ne les remplacer que par une pièce
portant le numéro spécifié.
• Divided circuit diagram
Schematic diagrams of A, AD, BM1C, DICA, G, M and P boards are divided into serveral pieces.
Information to where the line is to be connected is printed at the end of wach line.
For example, [ TO A1/2, A2/2_1 ] means the line is connected to
Ref. No. 1 of A (1/2) and A (2/2) schematic diagrams.
TO A1/2, A2/2_1
Ref. No.
Circuit diagram division code
Terminal name of semiconductors in silk screen
printed circuit (
*
)
Circuit
Device
Printed symbol
Terminal name
Collector
1
Transistor
Emitter
Base
Collector
2
Transistor
Base
Emitter
Cathode
3
Diode
Anode
Cathode
4
Diode
Anode
(NC)
Cathode
5
Diode
Anode
(NC)
Common
6
Diode
Anode
Cathode
Common
7
Diode
Anode
Cathode
Common
8
Diode
Anode
Anode
Common
9
Diode
Anode
Anode
Common
0
Diode
Cathode
Cathode
Common
!¡
Diode
Cathode
Cathode
Anode
Cathode
!™
Diode
Anode
Anode
Cathode
Anode
Transistor
Source
!£
Drain
D
D
(FET)
Gate
G
G
Source
Transistor
!¢
S
S
Drain
(FET)
Gate
D
D
Source
Transistor
!∞
Drain
G
G
(FET)
Gate
S
S
Emitter
!§
Transistor
Collector
Base
C1
C2
C2
B1 E1
!¶
Transistor
B1
B2
E2
B2 C1
E1
E2
C1
B2 E2
!•
Transistor
C1
C2
E1
B1 C2
B1
B2
!ª
C1
B2 E2
E1
E2
Transistor
E1
B1 C2
E1
E2
C1
B2 E2
@º
Transistor
B1
B2
E1
B1 C2
C1
C2
C1(B2)
C2
E2
B1 E1
@¡
Transistor
B1
C2
C1(B2)
E2
E2
(B2)
E1(B2)
E2
B1
E1
E2
@™
Transistor
B1
C1
C2
C1
C2
E1(B2)
C2
(B2)
E2
E1
B1
@£
Transistor
B1
C2
C1
C1
C2
–
Discrete semiconductot
Ver.1.6
(Chip semiconductors that are not actually used are included.)
KE-61MR1 (K)
4-16
Advertisement
Table of Contents
