Advertisement
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
IIMPORTANT – The wall brackets supplied with the
appliance must be used.
IMPORTANT – If the heater is installed in a room containing
a bath or shower, it must be so installed that switches
and other controls cannot be touched by a person using
a bath or shower.
Do not use outdoors.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or garments
on the heater, or obstruct the air circulation around the
heater, for instance by curtains or furniture, as this could
cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots
at the top of the heater or the air inlet slots in the base of
the heater.
The heater carries the Warning symbol indicating
that it must not be covered.
WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.
Momentary contact with any part of the heater should not
cause injury. However, aged or infirm persons or young
children should not be left unsupervised in the vicinity of
the heater unless a suitable guard is fitted.
This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Note that due care and consideration must be taken when
using this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent
electrician, and be in strict accordance with the current I.E.E.
regulations for Electrical Equipment in Buildings.
The wires in this mains lead are coloured in accordance with the
following code :
GREEN AND YELLOW :
BLUE :
BROWN :
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing conductor
in the supply cord is deemed to provide the supplementary bonding
connection (see Regulation 547-03-05, 16
Regulations).
General
This appliance is designed for wall mounting on the wall brackets
supplied. It should only be operated when in the upright position as
shown.
All models are splashproof to IP24 standard.
Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
EARTH
NEUTRAL
LIVE
th
Edition I.E.E. Wiring
Wall Mounting
IMPORTANT – The wall brackets supplied with the appliance must
be used. The heater should be positioned observing the minimum
clearances stated around the heater - see Fig. 1.
DO NOT locate the heater immediately below a fixed socket outlet or
connection box.
1. Remove wall mounting bracket from the back of the heater by
depressing the spring latch at the top of each bracket - see Fig. 2.
2. Fix the wall bracket securely to the wall through the four screw
holes provided.
3. Present the heater to the wall bracket, and engage lower slots
in the back with bracket.
4. Raise the heater to upright position and push the heater onto
brackets to engage top latch.
Operation
Switching On the Heater (see Fig. 3)
The button marked '
' controls the electricity supply to the electronic
thermostat. An indicator beside the '
is powered 'ON'.
Setting Desired Temperature (see Fig. 3)
The heater is fitted with an adjustable thermostat enabling the room
temperature to be controlled by adjusting the slider accordingly. The
min setting '
' represents a room temperature of approximately 5
and may be used for protection against frost. The 'MAX' setting
represents a room temperature of approximately 23
glows when the elements are actually heating.
Turn on the heater using the '
slider to the desired position. When the room temperature has reached
the desired level, the power to the elements will be reduced, the
heater will then maintain the room temperature at the chosen level.
NOTE - Should your heater fail to come on when the thermostat
slider is at a low setting, this may be due to the room temperature
being higher than the thermostat setting.
Runback timer and operating the unit
The runback time can be cancelled by pressing the button on the
timer again. The neon indicator will go out and the heater remains in
set back.
The heater will operate at a maximum thermostat setting of 23°C for
the preset runback time of 2 hours. After this time has expired, the
heater will revert back to operating at the setback temperature (preset
at 16-18°C) until the button is pressed again, thus always maintaining
a base level of temperature in the room.
If the heater remains uninterrupted at the setback temperature for 48
hours, the timer automatically assumes the room is unoccupied and
reverts to its Frost Protection setting (5°C) until such time that the
runback timer is activated again by pressing the button.
Safety - Overheat protection
For your safety this appliance is fitted with a thermal cut-out. In the
event that the product overheats for some reason, the cut-out
prevents excessive temperatures on the product by cutting the power
to the heater. Once the heater has cooled down, it will reset
automatically, it will continue to cycle on and off automatically until
the reason for overheating is removed.
' button shows when the unit
0
C. The ' ' symbol
' button and move the thermostat
0
C
Advertisement
