Advertisement
^
CAUTION! Before making a cut, make sure that the rotation h a n d k
i s
,
o c k e d
p r o p e r
|
y a
n
d
t
h
e
5
3
w
table is secured
2. MITRE STOPS AND TABLE ROTATION
a t t h e next s t o ^
t r e S t
°
P S
* ° °
1 5
° '
2 2
'
5
° '
3
° °
4 5
° *
^
'
i g M w
h
e
n
V
o u
t u r
"
t h e
t a b l e
>
1 4
w M I
automatically stop
To turn the table, make sure the table rotation handle is loose and m o v e
t n e t a b
|
e
t 0
t h e
d e s i r e d
a n g
|
e
. T h e n tighten the
table rotation handle.
B
"
} . ASSEMBLING THE SAW CLAMP
^
n e
'lamp can be mounted to the left or right of the saw
D
o
H>t use the saw without having tightened the part
P o s i <
i o n the clamp (A) by inserting the rod Fig.3 (B) into
locking k ^
o b
(
C
)
a
g
a
i
n
s t the shank of the clamp.
4. OPERATION OF THE CLAMP
1. The height of the clamp can be adjusted by loosening the locking kni,b
a
n
d
dragging the body of the clamp up or down.
Once the height of the clamp is adjusted, tighten the locking knob.
2. During operation, place the clamp so that the bottom of the sliding [j|
o c
|< j
u s
t touches the top of the piece of wood you are
working on.
3. Finally, tighten the piece against the table, tighten the knob until t h
e
p
i e c e
0
f
w o o c
j i
s
completely blocked. Once the cut is
complete, loosen the lock button; you can then slide or remove the p i e
c e
5. GUIDE EXTENSIONS
The cutting guide can be extended sideways for working on large piec-
e s
u
s
j
n
g
t w o extensions (A) Fig.4 that slide outward.
During bevel cutting operations, it is important that these extensions ^
e
p |
a C
e d to the outside so that they do not interfere
with the motor housing or the blade guard.
To do this:
PI
P E U G E O T
1. Loosen the hex bolt (B) using an
Allen key.
2. Loosen the locking knob (C).
3. Slide the extension to the desired position and tighten the
bolt (B) and then the knob (C).
AV
CAUTION! Please remove the right extension support guide completely when using the mitre s a w a t 4 5 ° . Remember to
replace the guide after the cut.
6. FITTING THE DUST BAG
1. Insert the dust bag (A) Fig.5 in the connection port
(B) on the back of the saw head and check that it is
properly attached.
If you wish t o improve the suction, a vacuum cleaner with a
dust suction hose can be connected directly
to the saw's elbow extraction.
NOTE: For best suction results, empty the bag
regularly t o avoid congestion (when
half full). The bag has a zipfor
easier emptying.This makes for better
•liiflow through the dust bag.The bag can also
be rinsed in warm soapy water and dried before being
reused.
Make sure the bag is properly attached.to the connection port
ind that the bag's zip is securely closed
before turning on the saw.
/ ! \! Dust particles can cause respiratory problems. Wearing a dust mask that complies with
irds is recommended for your protection.
the current stand-
7. FITTING THE SIDE EXTENSIONS
1 he mitre saw comes with t w o extensions to support large pieces of wood and thus prevent them sagging while you saw.
I Ktensions can
he mounted on both sides of the saw, depending on the
dimensions of the piece of wood.
1 he lateral extensions must be installed before attaching the
\.iw to a bench or a table.
1. lighten the tilt knob so that the blade
1 .innot move.
;. lower the table rotation handle so that
Hit' table cannot be moved.
I i inscrew the locking knob (A) Fig.6.
-I Insert the table extension (B) in the t w o holes found
In the base of the saw.
V lock the side extension in place by screwing the
locking knob (A).
ii Repeat steps 3-5 to install the second
Literal extension.
Advertisement
