Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LogN HN-DR4PN2U
Summary of Contents for LogN HN-DR4PN2U
- Page 1 HN-DR4PN2U User Manual...
-
Page 2: Table Of Contents
HN-DR4PN2U User Manual Contents Safety Precautions ..................... 1 Introduction ......................1 LED Status Description................2 2.1.1 Front Panel ................. 2 2.1.2 Rear Panel.................. 3 Hardware Installation ..................1 Choosing the Best Location for Wireless Operation......1 Connecting the ADSL Router ..............1 Introduction to Web Configuration.............. -
Page 3: Safety Precautions
HN-DR4PN2U User Manual Safety Precautions Follow the instructions below to prevent damage to the device and the risk of fire or electric shock: Use the power adapter supplied with the unit and plug it into a suitably rated power outlet. -
Page 4: Led Status Description
HN-DR4PN2U User Manual 2.1 LED Status Description Front Panel 2.1.1 The following table describes the LEDs of the device: LEDs Color Status Description The device is powered on and the device Green operates normally. Power The device and is initiating. -
Page 5: Rear Panel
HN-DR4PN2U User Manual LEDs Color Status Description Protected Setup. Wi-Fi Protected Setup is disabled. The connection of 3G or USB flash disk has established. Green Blink Data is being transmitted. The connection of 3G or USB flash disk is disabled. -
Page 6: Hardware Installation
HN-DR4PN2U User Manual Hardware Installation Choosing the Best Location for Wireless Operation Keep the numbers of walls and ceilings to the minimum. Consider the direct line between access points and workstations. Building materials make difference. Position the antenna for best reception. -
Page 7: Introduction To Web Configuration
HN-DR4PN2U User Manual Introduction to Web Configuration 4.1 Preparation before Login Before accessing the Modem, ensure the communication between PC and Modem is normal. Check the communication as follows. Configure the IP address of the PC as 192.168.1.X (2~254), net mask as 255. -
Page 8: Logging In To The Router
HN-DR4PN2U User Manual If the PC can read the MAC address of the Modem and can ping through the management IP address of the Modem, that means the communication of the PC and the Modem is normal. Note: When you manage the router through Web, do not cut off the power supply of the router. -
Page 9: Wan Configuration
HN-DR4PN2U User Manual After logging in to the DSL router as a super user, you can view, configure, and modify all the settings, and diagnose the system. 4.3 WAN Configuration 4.3.1 Layer2 Interface ATM Interface Choose Advanced Setup > Layer2 Interface > ATM Interface , and the following page appears. - Page 10 HN-DR4PN2U User Manual Figure 2 ATM PVC configuration In this page, you can set the VPI and VCI values, and select the DSL latency, link type (EoA is for PPPoE, IPoE, and Bridge.), connection mode, encapsulation mode, service category, and IP QoS scheduler algorithm.
- Page 11 HN-DR4PN2U User Manual Encapsulation Mode: You may select LLC/SNAP-BRIDGING or VC/MUX in the drop-down list. Service Category: you may select UBR Without PCR, UBR With PCR, CBR, Non Realtime VBR or Realtime VBR in the drop-down lsit. Select IP QoS Scheduler Algorithm: You may select Strict Priority and ...
-
Page 12: Wan Service
HN-DR4PN2U User Manual Figure 4 ETH WAN Configuration In this page, you can select an ETH port from the drop-down list and select Default Mode or VLAN MUX Mode as the connection mode. 4.3.2 WAN Service Choose Advance Setup > WAN Service, and the following page appears. - Page 13 HN-DR4PN2U User Manual Adding a PPPoE WAN Service This section describes the steps for adding the pppoe_0_0_40 (PPPoE mode) service. Step1 In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page. (At first, you must add a proper ATM or ETH configuration for this WAN service.)
- Page 14 HN-DR4PN2U User Manual Figure 7 WAN service configuration (PPPoE) Step3 In this page, select the WAN service type to be PPP over Ethernet (PPPoE). Click Next to display the following page. Figure 8 PPP username and password (PPPoE)
- Page 15 HN-DR4PN2U User Manual Step4 In this page, you can modify the PPP username, PPP password, PPPoE service name and authentication method. PPP Username: The correct user name provided by your ISP. PPP Password: The correct password provided by your ISP.
- Page 16 HN-DR4PN2U User Manual Figure 9 Routing-default gateway (PPPoE) Step6 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page. Figure 10 DNS server configuration(PPPoE) Step7 In this page, you may obtain the DNS server addresses from the selected WAN interface or manually enter the static DNS server addresses.
- Page 17 HN-DR4PN2U User Manual enter the static DNS server addresses. Click Next, and the following page appears. Figure 11 PPPoE summary Step8 In this page, it displays the information about the PPPoE settngs. Click Apply/Save to save and apply the settings, and then the following page appears.
-
Page 18: Wan Service
HN-DR4PN2U User Manual 4.3.3 3G WAN Service Choose Advanced Setup > 3G WAN Service , and the following page appears. This page is used to configure 3G connection. If you want to access the Internet through 3G connection, a 3G network card is required. Connect the 3G network card to the USB interface of the Router. - Page 19 HN-DR4PN2U User Manual In this page, you are allowed to configure the settings of the 3G USB modem. Enable USB Modem: If you want to access the Internet through the 3G network card, you must enable the USB modem.
- Page 20 HN-DR4PN2U User Manual Default WAN Connection Select: You can select DSL or ETHERNET or 3G from the drop-down list. WAN back mechanism: The 3G connection is backup for the DSL connection. DSL: If the DSL is disconnected, the 3G starts to dial.
Need help?
Do you have a question about the HN-DR4PN2U and is the answer not in the manual?
Questions and answers