Related Manuals for UCHIDA SP-22
Summary of Contents for UCHIDA SP-22
- Page 1 Operation Manual UCHIDA STAPLER-PUNCHER MODEL SP-22 Read this “Operation Manual” carefully before use. Keep it at a specific place for handy reference. 17 April 2006 - 0 -...
- Page 3 Safety Instructions Definition of Symbols and Notes In this manual following names and signs stand for possible dangers. Danger This Symbol stands for immediate danger threatening the life and health of persons. Disregarding these instructions may cause severe damage to health and even serious injuries.
-
Page 4: Table Of Contents
INTRODUCTION Read this “Operation Manual” carefully before use. Keep it at a specific place for handy reference. Since the specifications of this machine are subject to change, be sure not to mistake this manual for one of a different mode, descriptions of may differ. CONTENTS 1. - Page 5 7. Troubleshooting .........................16 Nature of problem and corrective action ..............16 7.2. In case of breakdown ....................17 8. Relocation or Disposal.......................17 Relocation ........................17 8.1.1 Removal of the machine from its present location ..........17 8.1.2 Transport......................17 8.1.3 Installation ......................17 Disposal ........................17 9. Product Specifications .......................18 Specifications......................18...
-
Page 6: Precautions Before Installation And Use
1. Precautions before Installation and Use 1.1 Place for installation This machine is also designed for IT power systems. (1) Install the machine on a stable and level place. (2) Use the Stapler-Puncher table designed for this machine. (3) Avoid installing the machine in the following places for safety’s sake and to avoid mechanical problems. -
Page 7: Component Name
2. Component Name 2.1 Overview... -
Page 8: Matters For Special Note
3. Matters for Special Note 3.1 Definitions Term Explanation Paper jam Paper stuck in the machine Double feed Feeding two or more sheets together 3.2 Characteristics and purpose of use Can staple and punch up to A3 size paper. Operation with or without punching can be selected. 3.3 When not in use Remove the power plug from the outlet. -
Page 9: Preparations Before Use
4. Preparations before Use 4.1 Installation (1) Set the shift lever at Connection. Connection Independent (2) Secure the hooks (one each at right and left sides) of the stapler-puncher to the collator hook pins. When removing them, do so while pulling out the hook lever (one each at right and left sides) of the stapler-puncher. -
Page 10: Operation
5. Operation 5.1 Procedure and method When using the stapler-puncher, also refer to the collator operation manual. (1) Turn the power switch on. (2) If stapling is not required, press the PROGRAM key on the collator operation panel to switch to Program mode. ( PROGRAM lamp will light) (3) Press the STAPLE/1 key on the operation panel. - Page 11 (5) Open the main cover and set the paper size shift knob to paper size. (6) Set the stapling position shift lever for the paper size. (7) If punching is not required, press the MODE key on the collator operation panel to switch to Program mode.
-
Page 12: Trouble Symptoms And Corrective Action
5.2 Trouble symptoms and corrective action The machine stops and the Paper Jam Paper jam: lamp on the collator operation panel flashes. Open the main cover, remove aligning to the left guide and remove paper from the side of the machine. The machine stops and the Error Staple cartridge (L) lamp on the operation panel... -
Page 13: Stapling And Punching Position
5.4 Stapling and punching position The machine is designed to punch holes in the center of each size paper. Set the stapling position according to paper size using the stapling position shift lever. 5.5 Staple cartridge replacement Use prescribed staples only. (1) Turn the power switch off and unplug the power plug from the outlet (be sure to do so to avoid an accident). - Page 14 (4) Conduct empty stapling Insert a sheet for empty stapling in the clincher portion of the machine and close the main cover. (5) Press the MODE key on the collator operation panel to switch to Program mode. ( MODE lamp will light) (6) Press the STAPLE/1 key on the collator operation panel for three seconds.
-
Page 15: Punching
5.6 Punching Each time the MODE key and PUNCH/2 key on the collator operation panel are pressed, punching mode will switch on and off. Punching mode On: PUNCH/2 lamp lit. Punching mode Off: PUNCH/2 lamp not lit. 5.7 Staple jam (1) Turn off the collator power switch and pull the power plug from the outlet (be sure to do so to avoid an accident). -
Page 16: Maintenance, Inspection, Expendables
6. Maintenance, Inspection, Expendables 6.1 Important for maintenance and inspection Danger When conducting inspections and maintenance, be sure to remove the power plug from the outlet. If not, it may cause injury or electric shock. 6.2 Daily maintenance Feed belt Occasionally clean the feed belt using the prescribed cleaning kit (sold separately). -
Page 17: Troubleshooting
7. Troubleshooting 7.1 Nature of problem and corrective action Status Possible Cause Corrective Action Cannot switch to Connectors (two) linking collator and Properly attach them. stapler-puncher staple-puncher improperly attached Stapler-puncher circuit beaker off Push circuit breaker button. Paper not neatly Paper not loaded neatly on each station Place paper in order, then set the guides close to delivered... -
Page 18: In Case Of Breakdown
Status Possible Cause Corrective Action No punching Punching mode not programmed Press the MODE a nd PUNCH/2 keys. ( PUNCH/2 lamp will light) Connectors (two) linking the collator Connect them firmly. and stapler-puncher loose or undone Stapler-puncher circuit breaker off Push the circuit breaker button. -
Page 19: Product Specifications
9. Product Specifications 9.1 Specifications Paper size A3, B4, A4, B5 Paper quality 53-81g/m Processing capacity Stapler-puncher: 660 sets/hour (A4 paper) Stapler : 840 sets/hour (A4 paper) Punch hole size Diameter: 6mm, 2 holes Pitch: 80mm For B5 ad A4 size, holes are punches at the center of the longitudinal side of the paper.