Related Manuals for UCHIDA ST-31
Summary of Contents for UCHIDA ST-31
- Page 1 Uchida ST-31 Large-Capacity Stacker Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 Operation Manual Large-Capacity Stacker ST-31 Read this “Operation Manual” carefully before use. Keep it at a specific place for handy reference. 27.03.2002...
- Page 4 Safety Instructions Definition of Symbols and Notes In this manual following names and signs stand for possible dangers. Danger This Symbol stands for immediate danger threatening the life and health of persons. Disregarding these instructions may cause severe damage to health and even serious injuries.
-
Page 5: Table Of Contents
INTRODUCTION Read this “Operation Manual” carefully before use. Keep it at a specific place for handy reference. Since the specifications of this machine are subject to change, be sure not to mistake this manual for one of a different mode, descriptions of may differ. CONTENTS 1. -
Page 6: Precautions Before Installation And Use
1. Precautions before installation and use 1.1 Place for installation Avoid installing the machine in the following places for the sake of safety and to prevent mechanical problems. [Precautions for installation] ・Locations with extremely high or low temperatures. Room temperature should be between 5 and 35 degrees centigrade. -
Page 7: Component Name
2. Component Name 2.1 Overview - 5 -... -
Page 8: Matters For Special Note
3. Matters for special note 3.1 When not in use ・Be sure to remove the power plug from the outlet. 4. Preparations before use 4.1 Assembly and installation of stacker (1) Assembly Insert the paper butt unit in the square hole on the stacking slide cover, and insert the gray connector into the plug of the stacking slide cover. -
Page 9: Installation And Dismantling Of Forceful Ejector
4.2 Installation and dismantling of forceful ejector (1) Switch the stacking switch lever to the connection side. (2) Firmly hook the pins (one black pin each on right and left sides) set at the lower part of the collator on the hook on the forceful ejector (on the stacker side). -
Page 10: Operation
5. Operation 5.1 When the division option is set to ON (1) Set the dolly on the dolly support. The “UP” lamp lights. Caution! Push the dolly deep into the end and set it in the correct position. The lamp will not light unless it is properly set. - Page 11 (4) Press the CHECK key on the collator’s operation panel to collate a set of paper and check the position of each guide. Caution! ・Set the guides in the position where an opening 2 to 3 mm wide will be left between the paper and each of the right and left guides, as well as an opening 5 to 20mm wide between the paper and the butt guide.
-
Page 12: When The Division Opsion Is Set To Off
Danger Do not operate the left stacking guide adjusting knob while the machine is in operation. Operating the adjusting knob while the machine is collating may cause an injury by making your fingers caught in the machine. Do not put your hand on the paper butt unit. As the unit is detachable, it may be removed, causing an injury. - Page 13 (3) Set both right and left stacking guides and the butt at appropriate positions. Press the CHECK key of the collator to collate one set of paper and check if the paper is neatly collated. Caution! Set the guides in the position where an opening 2 to 3 mm wide will be left between the paper and each guide, as well as an opening 5 to 20 mm wide between the paper and the stacking butt.
-
Page 14: Maintenance, Inspection, Expendables
・When starting to collate again (1) After removing the paper stacked on the dolly, raise the dolly again. If the dolly is raised with the paper left on it, detection of rising dolly edge cannot be correctly performed and it may cause the machine out of order. (2) Start collation after setting the paper neatly on the paper feed table of the collator. -
Page 15: Relocation Or Disposal
7. Relocation or Disposal 7.1 Relocation 7.1.1 Removal of the machine from its present location Be sure to pull out the power plug from the collator. Remove the stapler-puncher from the collator. 7.1.2 Transport ・Transport the removed parts, attachments and Operation Manual together with the machine. ・Take care not to expose the collator to strong vibration or shock.