Table of Contents
Advertisement
Quick Links
Arana RC
COAL EFFECT GAS FIRE
User Instructions
These instructions should be read by the user before operating the
appliance and retained for future reference
Model No's GICC**RN is only for use on Natural Gas (G20) at a
supply pressure of 20 mbar in G.B. / I.E.
Model No's GICC**RP is only for use on Propane Gas (G31) at a
supply pressure of 37 mbar in G.B. / I.E.
** denotes trim / fret variant
Advertisement
Table of Contents
Related Manuals for BFM Europe Arana RC
Summary of Contents for BFM Europe Arana RC
-
Page 1: User Instructions
Arana RC COAL EFFECT GAS FIRE User Instructions These instructions should be read by the user before operating the appliance and retained for future reference Model No’s GICC**RN is only for use on Natural Gas (G20) at a supply pressure of 20 mbar in G.B. / I.E. -
Page 2: Installation Information
The model no. of this appliance is as stated on the rating plate, located on the control panel of the fire. This product has been manufactured by : BFM Europe Ltd, Trentham Lakes, Stoke-on-Trent, ST4 4TJ Please Note : The life span of the batteries in the burner unit is dependent upon use and therefore the battery life will vary accordingly. -
Page 3: Important Safety Information
ABOUT YOUR NEW GLOBAL ARANA GAS FIRE The Global Arana RC convector coal effect gas fire incorporates a unique and highly developed fuel bed which gives the realism of a loose coal layout combined with realistic flames and glow. The use of durable ceramic material in the construction of the fuelbed components ensures long and trouble free operation. - Page 4 OPERATING THE FIRE USING THE REMOTE CONTROL HANDSET The Remote control handset generates an infrared signal, which will be received by the sensor situated at the front right of your fire, behind the ashpan cover. This infrared signal requires direct line of sight from the handset to the sensor on the fire to ensure good operation.
- Page 5 TURNING THE PRODUCT OFF IN THE UNLIKELY EVENT OF A REMOTE HANDSET MALFUNCTION. In the unlikely event of the remote control handset malfunctioning (or if lost or broken) after the appliance has been turned on, the fire can be turned off via the emergency shut off switch on the control panel. To turn the product off, firstly remove the ashpan from the fire.
-
Page 6: Spillage Monitoring System
SPILLAGE MONITORING SYSTEM This appliance is fitted with a spillage monitoring system which shuts down the fire if the evacuation of combustion products from the fire is affected by a partially or fully blocked flue. If this system operates the fire will go out. If this occurs, leave the fire for at least three minutes then follow the lighting procedure as described in the previous sec- tion. -
Page 7: Re-Assembling The Fuel Bed
RE-ASSEMBLING THE FUEL BED NOTE : The position of the fuel-bed components are critical to the performance of the product. Therefore please ensure that the fuel-bed components are positioned as described in the following section prior to requesting a service call due to soot build up, poor flame pattern etc. Place the ribbed ceramic fuelbed base on top of the fuelbed support and pull fully forwards to the burner. - Page 8 Fit five of the large sized coals onto the front ceramic rail, ensuring that they are evenly spaced. Use the recess’s in the front ceramic rail as a guide for placement. (See fig. 5 below) Fig. 5 Select four of the large coals and arrange behind the front row of coals, ensuring that flame paths as indicated below are not interupted, place one of the small coals at each end of the second row.
- Page 9 Select five of the large coals and arrange along the rear of the fuelbed, using the ribs in the rear of the fuelbed as a guide for placement. (See fig. 7 below) Fig. 7 Select the remaining four large coals and position to fill the gaps at each end of the third row of coals, as shown.
- Page 10 The exact position and fit of the coals may be finely adjusted to give the most pleasing and random appearance. Warning : Use only the coals supplied with the fire. When replacing the coals remove the old coals and discard them. Fit a complete set of coals of the correct type.
-
Page 11: To Replace The Battery Pack
GAS SAFE registered gas installer. The part numbers of the user replaceable parts are as follows, these are available from BFM Europe, whose details can be found below. Fuelbed base B-58690... - Page 12 Due to our policy of continual improvement and development the exact accuracy of descriptions and illustrations cannot be guarantee Part No. B-108170 Issue 4 BFM Europe Ltd Trentham Lakes Stoke-on-Trent Staffordshire ST4 4TJ Telephone - General Enquiries : (01782) 339000...