Related Manuals for e-Line Technology ELI-IP5-B5-49MR
Summary of Contents for e-Line Technology ELI-IP5-B5-49MR
- Page 1 5MP IP Network Camera User’s Manual ELI-IP5-B5-49MR Free Network Motion Tech-Support Activated Resolution Warranty Recording eLineTechnology.com 800.683.6835...
- Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;...
- Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ...................... 1 Overview ......................1 Features ......................1 Specifications (ELI-IP5-B5-49MR)............2 1.3.1 Performance ....................2 Framework ........................4 Multiple-function Combination Cable..............8 Framework and Dimension ................9 Bidirectional talk ....................10 2.3.1 Device-end to PC-end................10 2.3.2 PC-end to the device-end ................. - Page 6 Operation ......................17 Web Operation ......................19 Network Connection ..................19 Login and Main Interface ................. 19 FAQ ..........................21 Appendix Toxic or Hazardous Materials or Elements ............22...
-
Page 7: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology and G.711a audio compression technology, which maximally guarantee the audio and video quality. - Page 8 Model ELI-IP5-B5-49MR Parameter Main Processor High performance DSP Embedded LINUX System Support real-time network monitoring, local record, and remote Resources operation at the same time. User Interface Remote operation interface such as WEB, DSS, PSS System Status Micro SD card status info, bit stream statistics, log, and software version.
- Page 9 1-channel,RCA Audio Input 1-channel, RCA Audio Output Bidirectional Reuse the first audio input channel Talk Input Audio Bit Rate 8kbps 16bit/16kbps 16bit Audio Compression G.711A/G.711Mu Standard 396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area threshold ranges from 0 to 100. Motion Detect Activation event: alarm device, audio and video storage, image snapshot, log, email function and etc.
-
Page 10: Framework
2 Framework 2.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure Figure 2-1 Multiple-function combination cable Please refer to the following sheet for detailed information. Port Name Function Connection Note Power port. Input DC 12V or AC 24V. (convertor is required) Power input DC12V/AC24V... -
Page 11: Framework And Dimension
Port Name Name Note ALARM_COM Alarm output public port. Alarm output port. It is to output the alarm signal to the alarm device. ALARM_NO NO: normal open alarm output port. It shall work with ALARM_COM port. I/O Port Alarm input port 1. It is to receive the on-off signal ALARM_IN1 from the external alarm source. -
Page 12: Bidirectional Talk
2.3 Bidirectional talk 2.3.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the bidirectional talk function. - Page 13 Figure 2-4 Alarm Please refer to the following figure for alarm input information. See Figure 2-5. Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the logic “1”.
-
Page 14: Device Installation
3 Device Installation 3.1 Device Installation Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. Dig three holes in the wall or the surface, and then input the three expansion bolts to the holes and secure. -
Page 15: Adjust Lens
Figure 3-2 Micro-SD card 3.3 Adjust Lens Rotate lens counterclockwise, and take it down. You can see its front and rear adjusting rod. Front rod adjusts focus while rear rod adjusts zoom. After adjusting rod, rotate lens cover clockwise to fasten it. See Figure 2-3. -
Page 16: Adjust Bracket
Figure 3-3 Adjusting lens 3.4 Adjust Bracket You adjust bracket with a M4 inner hex screw. Before adjustment, you loosen the screw with inner hex wrench in accessories bag. Rotate rear cover 360°horizontally, and 90°vertically. Rotate pedestal 360°. Secure the screw with inner hex wrench after adjustment. See Figure 2-4. Note: M4 inner hex wrench must be secured, otherwise the pedestal will be unstable and device cannot be fixed to specific angle. -
Page 17: Button
Figure 3-4 Adjusting bracket 3.5 Button You can switch button to up/down to zoom in/out. You also can switch button to left/right to focus. Long press button for 2s for auto focus which makes video clear. See Figure 2-5 and 2-6. Note: The button is for motorized series only. - Page 18 Figure 3-5 Button Position Figure 3-6 Button...
-
Page 19: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 20 In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-3. In Figure 4-3, you can view device IP address, user name, password and port.
-
Page 21: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 22 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
-
Page 23: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device. factory default setup. Micro card Do not set the Micro SD card as the storage media to storage the write times schedule record file. -
Page 24: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device ○ ○ ○ ○ ○ ○ Construction Material ○ ○ ○ ○ ○...