1. Manuals
  2. Brands
  3. Videcon Manuals
  4. Security Camera
  5. VHSD-870EXT
  6. Instruction manual

Videcon VHSD-870EXT Instruction Manual

Videcon vhsd-870ext antivandal outdoor ip speed dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
Ver 1.4
ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA
| MPEG4 with Motion Tracking
Firmware Ver. 1.2.1a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VHSD-870EXT and is the answer not in the manual?

Questions and answers

Related Manuals for Videcon VHSD-870EXT

Summary of Contents for Videcon VHSD-870EXT

  • Page 1 INSTRUCTION MANUAL Ver 1.4 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA | MPEG4 with Motion Tracking Firmware Ver. 1.2.1a...
  • Page 2 This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

  • Page 3: Important Safeguard

    NOTICE Important Safeguard Read Instructions Read all of the safety and operating instructions before using the product. Retain Instructions Save these instructions for future reference. Attachments / Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product and void warranty.

  • Page 4: Table Of Contents

    CONTENTS ○ Introduction Features About Network Function Product & Accessories Parts Name & Functions ○ Installation Configure, fix and wire DIP Switch Setup Installation using Mount Bracket Cabling ○ Operation Check points before operation Preset and Pattern Function Pre-Check Starting OSD Menu Reserved Preset Preset Pattern...
  • Page 5 CONTENTS Case A : Dynamic IP or PPPoE + Personal Router Case B : Static(Fixed) IP + Personal Router Case C : Static(Fixed) IP Case D : Dynamic IP + DSL/Cable Modem Case E : PPPoE + DSL Modem Port Forwarding Starting IP Speed Dome ○...

  • Page 6: Introduction

    INTRODUCTION Features  Network Video Interface High frame are using hardware MPEG4 compression.  High frame rate with superior Video Quality  High speed : 30 fps at 720 x 480, 25 fps at 720 x 576  Web Browser based Viewer & i-Pro Multi Viewer supported. ...
  • Page 7 INTRODUCTION  Preset, Pattern,VST, Group, Privacy Mask and More…  Up to 127 sets of positional and zoom level information can be stored as presets. These can be called manually by the operator, automatically by an alarm input, or grouped to form a sequence of actions to run automatically.

  • Page 8: About Network Function

    INTRODUCTION About Network Function This product is only compatible with current versions of the Microsoft Windows OS.  This product operates with Microsoft’s Internet Explorer only.  You must have ActiveX controls enabled on your browser, found in the Options menu. ...

  • Page 9: Product & Accessories

    INTRODUCTION Product & Accessories  Product & Accessories  Main Body  Wall Mount Bracket  Screws & Terminal Block  Crossover Cable  Options  Ceiling Mount Bracket  Corner Mount Bracket  Pole Mount Bracket 9/95 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA / MPEG4 with Motion Tracking...

  • Page 10: Parts Name & Functions

    INTRODUCTION Parts Name & Functions BracketJoint BracketJoint Housing Upper Cover Housing Upper Cover Thermostat Thermostat Heater Heater BracketMount BracketMount Base Base Thermostat Thermostat Bracket U pper Bracket U pper Cover Cover Seal Seal Sunshield Sunshield Shield Mount Shield Mount TiltMotor TiltMotor DomeHousing DomeHousing...
  • Page 11 INTRODUCTION This green indicator should be flashing or glowing during normal  LINK LED operation. During a reboot or power cycling, it may take up to 50 seconds to initialize, negotiate your network speed, and begin operation at 10 or 100Mbps.

  • Page 12: Installation

    INSTALLATION Configure, fix and wire Foam Foam ① Wearing the gloves and using the supplied tool, ② Remove the foam pieces from the camera remove the outer dime cover. module. Lanyard Protocol Cover ③ Carefully unclip the black inner dome ④...

  • Page 13: Dip Switch Setup

    INSTALLATION DIP Switch Setup Before you installed camera or After you mount the camera, you should set the DIP switches properly to match your control equipment. Most important settings are camera ID, communication protocol and its speed. As Shown in the Picture bellow, there are two dip switch for protocol and ID ID (8P) Protocol (6P) ...
  • Page 14 INSTALLATION  Communication Protocol Setup Select the appropriate Protocol with DIP switch combination.  Switch State Protocol (Pin 1) (Pin 2) PELCO-D, 2400 bps PELCO-D, 9600 bps PELCO-P, 4800 bps PELCO-P, 9600 bps If you want to control using DVR or P/T controller, their protocol must ...

  • Page 15: Installation Using Mount Bracket

    INSTALLATION Installation using Mount Bracket ① Fix the supplied mounting template, taking ② after making suitable checks fir buried pipes and account of any pipework, cables, overhangs cables, drill fixing holes suitable for the bolts etc.that may obstruct the bracket once fitted. supplied with the speed dome ③...
  • Page 16 INSTALLATION ⑦ 1a-wall bracket option. After making all the 1b-pendent option. After making ⑧ connections to the PCB, fit the junction box cover connections to the PCB, raise the dome assembly with the four screws. to the junction box, connect the dome cable to the PCB and fix with the four screws.

  • Page 17: Cabling

    INSTALLATION Cabling * NOTE: As shown in the drawing, you can change the type of Relay Out (NC or NO) by shifting the jumpers near by terminal blocks of Alarm Outputs.  Power Connection Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the ...
  • Page 18 INSTALLATION  Video Connection Connect with BNC coaxial cable.  18/95 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA / MPEG4 with Motion Tracking...
  • Page 19 INSTALLATION  Alarm Input Connections  Sensor Input Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general, the cabling must be done properly after considering these typed.

  • Page 20: Operation

    OPERATION Check points before operation Before power is applied, please check the cables carefully.  The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked  by reading DIP switch of the camera. If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.

  • Page 21: Starting Osd Menu

    OPERATION Starting OSD Menu  Function Using the OSD menu, Preset, Pattern, VST, Group and Alarm Input function can be configured for each application.  Enter Menu <Go Preset> [95] Reserved Preset  Description Some Preset numbers are reserved to special functions. ...

  • Page 22: Preset

    OPERATION Preset  Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset.

  • Page 23: Pattern

    OPERATION Pattern  Function Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of controller for assigned time and revives the path exactly as it memorized. 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern.

  • Page 24: Group

    OPERATION Group  Function The group function allows running sequence of Presets, Pattern and/or VSTs. Max 8 group can be stored. Each group can have max 20 action entities which can be preset, pattern or VST. Preset speed can be set up and the repeat number of Pattern & VST can be set up in Group setup.

  • Page 25: Other Functions

    OPERATION Other Functions  Power Up Action This function enables to resume the last action executed before power down. Most of actions such as Preset, Pattern, VST and Group are available for this function but Jog actions are not available to resume. In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera keep ...

  • Page 26: Osd Display Of Main Screen

    OPERATION OSD Display of Main Screen PRESET LABEL: If defined, ACTION TITLE: Shows is displayed when a preset current speed dome position is called action R E C E P T I ON P R E S E T3 ALARM I/O: Shows which DATE/CLOCK: Shows alarm inputs and outputs are current time and date...

  • Page 27: How To Use Osd Menu

    HOW TO USE OSD MENU General Rules of Key Operation for Menu The menu items surrounded with ( ) always has its sub menu.  For all menu level, to go into sub menu, press NEAR key.  To go to up-one-level menu, press FAR key. ...

  • Page 28: Display Setup

    HOW TO USE OSD MENU Display Setup  Display Setup This menu defines Enable/Disable of OSD display on Main Screen. If an item is set to be AUTO, the item is displayed only when the value of it is changed. DISPLAY SET UP -------------------------------------- ...

  • Page 29: Privacy Zone Mask Setup

    HOW TO USE OSD MENU Privacy Zone Mask Setup From the display setup menu, use the joystick to highlight PRIVACY ZONE and key : NEAR Select area in image to mask. PRIVACY ZONE  Mask No [1~8] -------------------------------------- ZONE NO Select Mask number.

  • Page 30: Dome Camera Setup

    HOW TO USE OSD MENU Dome Camera Setup From the main menu, use the joystick to highlight DOME CAMERA SET DOME CAMERA SETUP UP and key: NEAR -------------------------------------- <CAMERA SETUP> <MOTION SETUP>  Camera setup setup of specific camera module features. <PRESET SETUP>...
  • Page 31 HOW TO USE OSD MENU  Camera Setup From the dome camera setup menu use the joystick to highlight ZOOM CAMERA SETUP -------------------------------------- CAMERA SETUP and key : NEAR FOCUS MODE AUTO DIGITAL ZOOM FLICKERLESS  Focus Mode [AUTO/MANUAL/SEMIAUTO] COLOUR <WHITE BALNCE SETUP>...
  • Page 32 HOW TO USE OSD MENU  White Balance Setup From the dome camera setup menu,use the joystick to highlight WB SETUP - GLOBAL CAMERA SETUP and key : NEAR ------------------------ WB MODE AUTO ADJUST  WB Mode [AUTO/MANUAL] BLUE ADJUST In Manual mode, Red and Blue level can be set up manually AUTO—the speed dome determines the optimum...
  • Page 33 HOW TO USE OSD MENU  Auto Exposure Setup  Backlight [ON/OFF] Sets Backlight Compensation AE SETUP -------------------------------------- BACKLIGHT  Day/Night [AUTO/DAY/NIGHT] DAY/NIGHT AUTO AE MODE AUTO The operator can choose to the camera in to IRIS LEVEL  GAIN LEVEL ...
  • Page 34 HOW TO USE OSD MENU  Motion Setup Setup the general functions of Pan/Tilt motions. MOTION SETUP  Preset Lock [ON/OFF] ------------------------ PRESET LOCK If Preset Lock is set to ON, it is impossible to set PWR UP ACTION AUTO FLIP up and delete Preset, Swing, Pattern and JOG MAX SPEED 120/SEC...
  • Page 35 HOW TO USE OSD MENU  Parking Action Setup If Park Enable is set to ON, camera runs assigned function automatically PARKING ACTION SETUP ------------------------ if there is no PTZ command during assigned "Wait Time". PARK ENABLE WAIT TIME 00:10:00 ...

  • Page 36: Preset Setup

    HOW TO USE OSD MENU Preset Setup  Preset Number [1~128] If a selected preset is already defined, camera PRESET SETUP --------------------------------- moves to pre-defined position and preset  PRESET NO. characteristics such as Label and Relay Outputs CLR PRESET CANCEL show on monitor.
  • Page 37 HOW TO USE OSD MENU  Edit Preset Scene Using Joystick, move camera to desired position. ○ EDIT SCENE - PRESET 1 ------------------------ By pressing NEAR key, save current PTZ data. ○ Press FAR key to cancel. ○ MOVE TO TARGET POSITION [NEAR:SAVE /FAR:CANCEL] ...

  • Page 38: Vst Setup

    HOW TO USE OSD MENU VST Setup  VST Number [1~8] VST SETUP --------------------------------- Selects VST number to edit. If a selected VST has  VST NO. 1ST POS. PRESET 5 not defined, "NOT USED" is displayed in 1st 2ND POS. PRESET 6 Position and 2nd Position VST SPEED...

  • Page 39: Pattern Setup

    HOW TO USE OSD MENU Pattern Setup  Pattern Number [1~4 ] PATTERN SETUP --------------------------------- Selects Pattern number to edit. PATTERN NO. If a selected pattern number is not defined, CLR PATTERN CANCEL RUN PATTERN "UNDEFINED" will displayed under <EDIT PATTERN> selected pattern number.

  • Page 40: Group Setup

    HOW TO USE OSD MENU Group Setup  Group Number [1~8] GROUP SETUP --------------------------------- Selects Group number to edit. GROUP NO. If a selected Group number is not defined, CLR GROUP CANCEL RUN PATTERN "UNDEFINED" will be displayed under selected <EDIT GROUP>...
  • Page 41 HOW TO USE OSD MENU ④ Set up items such as Action, ###, Dwell and OPT. EDIT GROUP 1 ------------------------ NO ACTION ### DWELL OPT ------------------------ 1 PRESET 1 00:03 360 2 NONE 3 NONE 4 NONE 5 NONE ------------------------ SAVE :MOVE CURSOR] CANCEL [...

  • Page 42: System Initialize

    HOW TO USE OSD MENU System Initialize  Clear All Data Deletes all configuration data such as display, SYSTEM INITIALIZE camera, motion setup and so on. ------------------------ CLEAR ALL DATA CLR DISPLAY SET  Clear Display Set Initializes Display Configuration CLR CAMERA SET CLR MOTION SET CLR EDIT DATA...

  • Page 43: Network Setup

    NETWORK SETUP DDNS Registration If you have DYNAMIC IP service from your Internet Service Provider (ISP), you can’t tell what current IP address of IP Speed Dome is. To solve this problem, you have to register to our DDNS service. At first, we recommend, you have to check if you are using dynamic addressing.

  • Page 44: Quick Start Of Network Connection

    NETWORK SETUP Quick Start of Network Connection Please follow the steps below to complete the initial setup of the Network Function.  Please do not power on the IP Speed Dome until instructed.  Temporarily disable any proxy servers configured in Internet Explorer. ...
  • Page 45 NETWORK SETUP ⑪ Configure the IP Speed Dome’s TCP/IP settings as you would any other PC on your network, providing a proper IP address, subnet mask, default gateway, and DNS server.  If this is standalone unit with a direct connection to a cable/DSL/Broadband modem then input the addresses you have received from your ISP.

  • Page 46: Initial Setup Via A Crossover Cable

    NETWORK SETUP Initial Setup via a Crossover Cable This section provides a guide on how to connect the IP Speed Dome to your PC/laptop for initial setup. Please follow the instructions in the order they appear, without skipping steps. Do not supply power to the IP Speed Dome, until instructed.
  • Page 47 NETWORK SETUP ⑥ Now you will be able to access the viewer software within the IP Speed Dome.  Open Internet Explorer and type the IP address of 192.168.1.80 (default IP of the IP Speed Dome from the factory) into the Address Bar of the web browser (as seen below). Press Enter.
  • Page 48 NETWORK SETUP ⑧ The default ID and Password are both the word “admin” (without the “”) ⑨ If at any time you are prompted to download ActiveX controls, you must click ‘Yes’, all content is safe.  You will have to click “Yes” twice to two individual prompts. This allows your video to be displayed in Internet Explorer.

  • Page 49: Guide To Network Setup

    NETWORK SETUP Guide to Network Setup Please configure the IP Speed Dome at the location of its installation. You must determine your network scenario in order to configure the IP Speed Dome with the proper TCP/IP settings. This tutorial will guide you through the process.
  • Page 50 NETWORK SETUP ⑤ Depicted below are several basic network scenarios. Determine which scenario describes your network. If your network does not match one of the scenarios below and are unsure how to setup your IP Speed Dome, please contact your network administrator, then call our Support Center.
  • Page 51 NETWORK SETUP  192.168.0.1 [Example]  Default Gateway  This IP address must be the IP address of your router (private or LAN side)  Use the same Default Gateway you noted under “Current TCP/IP Settings”  Use the 1st DNS Server from “Assigned IP Address from My ISP” ...
  • Page 52 NETWORK SETUP Case B : Static(Fixed) IP + Personal Router [Efficient] Configure your IP Speed Dome's TCP/IP properties as follows :  STATIC  Network Type  A private IP address such as 192.168.0.200 [Example]  Internet Address  You need to assign the IP Speed Dome an IP address, just as you would assign a PC.
  • Page 53 NETWORK SETUP  8888  Web Server Port  Do NOT use the default port 80, you must change this number.  You may select any number between 1025 ~ 30000.  7777  Control Server Port  You may select any number between 1025 ~ 30000. ...
  • Page 54 NETWORK SETUP Case C : Static(Fixed) IP [Dedicated line directly to the IP Speed Dome] Configure your IP Speed Dome's TCP/IP properties as follows :  STATIC  Network Type  A static IP address received from your ISP, such as 24.107.88.125 [Example] ...
  • Page 55 NETWORK SETUP  7778  Video Server Port  You may select any number between 1025 ~ 30000.  7779  Audio Transmit Server Port  You may select any number between 1025 ~ 30000.  7780  Audio Receive Server Port ...
  • Page 56 NETWORK SETUP Case D : Dynamic IP + DSL/Cable Modem [Connected directly to the IP Speed Dome] Configure your IP Speed Dome's TCP/IP properties as follows :  DYNAMIC  Network Type  Use the DDNS server  DDNS Server ...
  • Page 57 NETWORK SETUP Case E : PPPoE + DSL Modem [Connected directly to the IP Speed Dome] Configure your IP Speed Dome's TCP/IP properties as follows :  PPPoE  Network Type  Use the User ID or Username you received from your ISP for this direct ...

  • Page 58: Port Forwarding

    NETWORK SETUP Port Forwarding After entering the correct TCP/IP settings you will be ready for “Port Forwarding” (Cases A, B).  Please record the TCP/IP settings of your IP Speed Dome for future reference. You may need this information to access your IP Speed Dome and to configure “Port Forwarding”. IP Speed Dome TCP/IP Settings IP Address Subnet Mask...
  • Page 59 NETWORK SETUP Starting IP Speed Dome After correctly forwarding the Web Server Port , Video Server Port, Control Server Port and two Audio Ports through your router (if applicable), you may then install the IP Speed Dome in a proper location. ①...

  • Page 60: Web Viewer Screen

    WEB VIEWER Web Viewer Screen In this section, the main GUI of the IP Speed Dome will be explained.  General Tab ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○...

  • Page 61: Web Viewer

    WEB VIEWER Zoom, Focus, and Iris controls for the camera connected to IP Speed Dome. If you drag the each handle, ○ Zoom, Focus, and Iris are adjusted individually according to your mouse motion. Tap to switch General or Special function controls. The picture above shows controls when general ○...
  • Page 62 WEB VIEWER WEB VIEWER  Special Tab ○ ○ ○ ○ ○ ○ ○ ○ ○ Tab to switch General controls. ○ Click it to create new map automatically. Before creating new map, please, make sure Camera model in ○ the “Motion Tracking”...
  • Page 63 WEB VIEWER (c) Stop and save setting by clicking [Detection Area Setting] button. Masked Area No detection Unmasked Area Effective detection This defines the sensitivity of motion detection. Move small circular handle toward the + direction to ○ increase the sensitivity. Click it to turn Motion Tracking function on or off.

  • Page 64: How Does Motion Tracking Work

    WEB VIEWER How does Motion Tracking work? The “Motion Tracking (MT)” means intelligent Wait at Home Till Target detected moving object following using PTZ camera to get the best incoming information to figure out behavior of moving target in the region of Camera interest.
  • Page 65 WEB VIEWER Priority Rule: Basically, if there are two moving objects crossing, MT will follow bigger sized object. Rejection of Oscillating Objects: If there is an object oscillating limited distance like swaying tree, flag, MT will consider the distance and count number of oscillation. If the number exceeds the setting value in Motion tracking menu, it will return to home.
  • Page 66 WEB VIEWER Create, Save, Load Map Firstly, make sure Camera Model in “Motion Tracking” menu and PTZ Protocol in “Control” menu Administration Tools before creating Map. Also, most map related function except “Load” can be operated only by the user who has Administrator authority. ...

  • Page 67: Preset

    WEB VIEWER Preset If you draw a box on the map as shown in the picture bellow, the PTZ camera will move and change the zoom ratio to obtain the optimal video matched with the box you just draw. As shown bellow, if you click the right button of a mouse, you will see the menu item [Save Preset]. If you choose this, you will see a dialog box to specify Preset Number and Dwell Time.

  • Page 68: Group

    WEB VIEWER Group If you drag a preset number in the yellow box on the map and drop it into the group list box as shown in the picture bellow, corresponding Preset number will be added and registered like “P000” as a member of Group. Maximum 20 presets can be member of one Group.

  • Page 69: Viewer Interface

    WEB VIEWER Viewer Interface  Click N Go By clicking a target in main view, PTZ camera will move to locate the center of view to the target.  Box N Go By drawing a box on the target in main view, PTZ camera will move the camera view to the center of the box and change zoom ratio to match the view size with that of the box surrounding the target.

  • Page 70: Video Tool

    ADMIN TOOL This section is provided to familiarize the user with the administration tools. Intuitive options are not explained in detail. All the changes on Administration Tools take effect immediately. These settings will be global, affecting the view of all users currently logged on. However, OSD items selections are effective only after you refresh the viewer windows or restart the internet Explorer.
  • Page 71 ADMIN TOOL  Frame Rate Maximum frame rate of video to limit the traffic occupied.  Camera Flip Flip the video orientation. (i.e. Turn the video upside down.)  P/T Direction Define the direction of Pan/Tilt motion.  Video Compression Choose the video compression method form Motion JPEG and MPEG-4 formats. ...

  • Page 72: Control Tool

    ADMIN TOOL Control Tool  Com1 For PTZ devices only. Select the PTZ control protocol.  Com2 For Digital I/O module only. Select the module type.  PTZ Camera ID For PTZ Device Address Setup. 0 ~ 255 are available. ...

  • Page 73: Motion Detection Tool

    ADMIN TOOL Motion Detection Tool  Detection Action Set up the reaction of IP Speed Dome when motion detected. Alert Sound : Audio Out through the Audio out jack of IP Speed Dome. Out 1 ~ 4 : Select output relay numbers in the Sensor Alarm I/O module connected with IP Speed Dome.

  • Page 74: Motion Tracking Tool

    ADMIN TOOL Motion Tracking Tool  Camera Select model of Zoom Camera Module.  Tracking Sensitivity Select the sensitivity 0~7 for target’s movement during Motion Tracking. The bigger number, the more sensitive.  Tracking Range Define the coverage of “Motion Tracking operation”. If you want to apply motion tracking for all area, check the box before ALL.
  • Page 75 ADMIN TOOL  1x Zoom Wait The time out of waiting after 1x zoom state. If camera loses a target object, it will automatically zoom out to 1x to search the object lost. If there is no moving object for a while, the camera will return to Home Position where “Motion Tracking”...

  • Page 76: Tcp/Ip Tool

    ADMIN TOOL TCP/IP Tool  Network Type Select a Static or Dynamic address scheme that is used by the Internet Service Provider (not the addressing scheme used by a personal router).  Internet Address Input a value to assign an IP address to the IP Speed Dome. ...

  • Page 77: Ddns Tool

    ADMIN TOOL DDNS Tool  Use DDNS If you check this box, DDNS updating is enabled. (primary and secondary)  Primary DDNS Address Assign DDNS address. (default. www.net4c.net)  Secondary DDNS Select DDNS Provider. Currently, DtDNS is available. Provider  Host Name Type the host name registered in DDNS service (i.e.

  • Page 78: Smtp Tool

    ADMIN TOOL SMTP Tool This function is used to email the specified email recipient and notify that individual of the IP address / web port number used to access the IP Speed Dome. This email function is only activates on power-on reset time of IP Speed Dome.

  • Page 79: Date & Time Tool

    ADMIN TOOL Date & Time Tool  Current Date/Time It shows the current Date/Time setting of IP Speed Dome.  New Date/Time Select the method of Date/Time setting. Date/Time can be set by local computer or time server or manual. 79/95 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA / MPEG4 with Motion Tracking...

  • Page 80: Users Tool

    ADMIN TOOL Users Tool  System Manager Specify an ID and Password for the System Administrator of the IP Speed Dome. The System Administrator will have all rights and privileges to manage the system. After changing Administrator’s ID and Password, IP Speed Dome should ...

  • Page 81: Firmware Update Tool

    ADMIN TOOL Firmware Update Tool  Version Shows the current firmware version.  How to upgrade Click [Browse…] button and select the latest version of the firmware. Its file name should be ***.bin. Click [Update Start] button. It will start upgrading its firmware. IP Speed Dome will re-boot automatically as soon as it finish the upgrade process.

  • Page 82: Default Set Tool

    ADMIN TOOL Default Set Tool Reset its system configuration to the factory defaults. Note) After initializing, all information should be deleted. Please re-consider before initializing. Rebooting Tool Re-boots IP Speed Dome. 82/95 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA / MPEG4 with Motion Tracking...
  • Page 83 APPENDIX A : Current TCP/IP Settings  For Windows 98 / ME Users  Note the settings under the IP Address, DNS Configuration, and Gateway tabs  If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your IP address.
  • Page 84 APPENDIX B : Changing your computer’s IP address and subnet mask  For Windows 98 / ME Users  Select 'Use the following IP address' and change the IP address and Subnet Mask.  For Windows 2000 or Windows XP ...

  • Page 85: C : Port Forwarding

    APPENDIX C : Port Forwarding After assigning the IP Speed Dome a web server port and video server port you must use Port Forwarding (for cases A, B) Please consult your router’s user guide on how to correctly configure Port Forwarding. For your convenience, we have provided two example configurations.
  • Page 86 APPENDIX  Enabled / Disabled Select “Enabled”.  Name Input IP Speed Dome name.  Private IP Input IP Speed Dome address.  Protocol Type Select “TCP”  Private Port / Public Port Input IP Speed Dome Web Server Port. ...
  • Page 87 APPENDIX  For Linksys BEFSR41 Cable/DSL routers: Open a web browser and type http://192.168.1.1 into your Address bar (the default IP address to access ① the router) You will have to supply your User Name and Password to log onto the router. Default from factory (User ②...
  • Page 88 APPENDIX  For Netgear RP614 routers Input http://192.168.0.1 in address bar of web browser. http://192.168.0.1 is the default IP address. ① If it asks ID and password, input admin as ID and password as password. ② Click “Port Forwarding” in "Advanced". ③...
  • Page 89  I can’t connect!! In the case of a connection failure. Modem Reboot  Modem Reboot Finished  Router Reboot  Router Reboot Finished  IP Speed Dome Reboot  IP Speed Dome Reboot Finish  Verify DDNS and IP Speed Dome connection, if applicable.
  • Page 90 How do I find out my IP address information if my settings were  automatically detected?  Windows 98 / ME Users ① Open an MS-DOS Prompt ② At the prompt type:“winipcfg” (without the quotation marks) ③ Use the drop down list to select your 10/100 Ethernet Adapter (not a PPP adapter) ④...
  • Page 91  My LINK light is not flashing or solid? Verify the cable connection. 99% of the time the cable’s connection to the unit is causing this problem. Try using a different network cable or crossover cable (for PC connection only). Try reinserting the cable, if this still doesn’t solve the problem call our Support Center.
  • Page 92  Can I use the IP Speed Dome on my dial-up Internet connection? No, we recommend a high-speed broadband connection of at least 128Kb/sec.  I’m accessing my video server remotely over the Internet and the video stream is choppy, is this normal? Yes.

  • Page 93: Specifications

    SPECIFICATIONS Specifications Sensor 1/4" interline EX-View ccd Max.Pixels N:811(H)x508(V)410K, P795(H)x596(V)470K Effective Pixels N:768(H)x494(V)380K, P752(H)x582(V)440K Horizontal Res. 520~540TVL S/N Ratio More than 50db Zoom 18x Optical Zoom, 12x Digital Zoom Camera Focal Length 18times :F1.4(w)3.0(T) f=4.1~73.80mm Min. illumination 0.01Lux(ICR on) Day & Night Auto Focus Auto/Manual...
  • Page 94 SPECIFICATIONS Network 32Bit RISC Processor Embedded Linux Flash Memory Network 10/100 Base-T Ethernet (RJ-45) Compression Selectable MJPEG and MPEG-4 ASP Level 5 Frame Rate 30 @ 720×480 : 25 @ 720×576 Audio Bidirectional/ ADPCM Video Streaming CBR, VBR, Adjustable Bit Rate Number of Users Max.
  • Page 95 SPECIFICATIONS Dimension & Options Options Ceiling Mount bracket pole mount bracket corner mount bracket ** wall mount included 95/95 ANTIVANDAL OUTDOOR IP SPEED DOME CAMERA / MPEG4 with Motion Tracking...

Table of Contents