Page 2
HCP reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases, consult the HCP to determine whether any such changes made. HCP will not be liable for technical or editorial errors or omissions contained herein: nor for incidental or consequential damages incurred when using this manual.
1. Cable connection *USB interface scanner installation Make sure that the scanner has the correct cable for your system. Connect the cable to the USB port of the PC or POS. *RS-232C interface scanner installation Make sure that there is a power supply to the scanner (If necessary). Some devices deliver power through serial port using SUB D9 connector on 9 (Chapter 20) Connect the cable to the RS-232C port of the PC or POS.
Right Wrong 3. Setup procedure The general procedure to program is as follows: Scan the command symbol “Program”, Scan one or more parameters, Scan the command symbol “End” to close procedure. Example 1. To set RS 232 parameters 9600,N,8,1 (Page 7 - 9) Scan the barcode “Program”, Scan “9600”...
Programming 5. Keyboard interface 5 - 1. Device selection IBM PC/XT IBM PC/AT* IBM PC/PS2 LAPTOP 5 - 2. Function code selection Function key On* Function key Off Lower Case* Upper Case Num-Lock Off* Num-Lock On - 10 -...
Page 11
Programming Program 5 - 3. Language German French Swiss Swedish Japanese Spanish Norwegian Italian Universal - 11 -...
Programming 8. Data Format 8 - 1. Terminator TAB(CR/LF) Enter(CR)* Return(LF) None 8 - 2. Code ID None* User defined Default Example: If barcode ID for code39 (standard) defined as “U”, scan “Program” ”User defined” “Define Code ID” “Code39(standard)” “U” “Code39(standard)” “Define Code ID”...
Page 17
Programming Program 8 – 3. Code ID Setting Define Code ID Code 39(M) (Full ASCII) Code 39(M) (Standard) EAN – 13(F) UPC – A(A) EAN – 8(F) UPC – E (E) Code 93(L) - 17 -...
Page 18
Programming Codabar (N) Code 128 (K) I 2 of 5 (I) S 2 of 5 (H) D 2 of 5 (H) M 2 of 5 (H) China postage (C) Code 3 of 5 (P) MSI/Plessey (O) Code 11 (J) - 18 -...
Page 19
Programming Program 8 - 4. Custom setting Single edit mode Select from left Select from right Custom mode Enable Example: If 5 digits from the left are required, scan “Program” “Single edit mode” “Select from left” “0” “5” “Select from left” “Single edit mode” “Custom mode enble”...
Page 20
Programming 8 - 5. Data length Exclude* Include 8 - 6. Preamble/Postamble Preamble Postamble Example: If preamble “SN” before data is required, scan “Program” “Preamble” “S” “N” “Preamble” “End”. Reserved1 Reserved2 Reserved3 - 20 -...
Programming Program 9. Barcode setting 9 - 1. Code39 Code 39 Enable* Code 39 Disable Full ASCII Code 39* Standard Code 39 Code 32 Enable Code 32 Disable* Verify Check & Transmit Verify Check & Not Transmit Not Verify Check* - 21 -...
Page 22
Programming 9 - 2. Interleaved 2 of 5 I 2 of 5 Enable* I 2 of 5 Disable Fix Length On Fix Length Off* 1st Dig. Suppress Last Dig. Suppress No Suppress* Example: If barcode length needs to be fix, scan “Program“ “Fix Length On“ “End“...
Page 23
Programming Program I 2 of 5 Verify Check & Transmit I 2 of 5 Verify Check & Not Transmit I 2 of 5 Not Verify Check* Code 3 of 5 Enable Code 3 of 5 Disable* Code 3 of 5 Transmit Check Code 3 of 5 Not Transmit Check* - 23 -...
Page 24
Programming 9 - 3. Standard 2 od 5 S 2 of 5 Enable S 2 of 5 Disable* Fix Length On Fix Length Off* Verify Check & Transmit Verify Check & Not Transmit Not Verify Check* - 24 -...
Page 25
Programming Program 9 - 4. Industrial 2 od 5 D 2 of 5 Enable D 2 of 5 Disable* Fix Length On Fix Length Off* Verify Check & Transmit Verify Check & Not Transmit Not Verify Check* - 25 -...
Page 26
Programming 9 - 5. Matrix 2 od 5 M 2 of 5 Enable M 2 of 5 Disable* Fix Length On Fix Length Off* Verify Check & Transmit Verify Check & Not Transmit Not Verify Check* - 26 -...
Page 27
Programming Program 9-6. China postage China postage Enable China postage Disable* Fix Length On Fix Length Off* Verify Check & Transmit Verify Check & Not Transmit Not Verify Check* - 27 -...
Page 29
Programming Program 9 - 9. UPC – A UPC – A Enable* UPC – A Disable Leading Digit On* Leading Digit Off Add Leading Zero On Add Leading Zero Off* Transmit Check Digit* Not Transmit Check Digit - 29 -...
Page 30
Programming 9 - 10. UPC - E UPC - E Enable* UPC - E Disable Leading Digit On* Leading Digit Off Transmit Check Digit* Not Transmit Check Digit Zero Expansion On Zero Expansion Off* - 30 -...
Page 31
Programming Program 9 - 11. EAN - 8 EAN – 8 Enable* EAN – 8 Disable Leading Digit On* Leading Digit Off Transmit Check Digit* Not Transmit Check Digit - 31 -...
Page 32
Programming 9 - 12. EAN - 13 EAN - 13 Enable* EAN - 13 Disable Leading Digit On* Leading Digit Off Transmit Check Digit* Not Transmit Check Digit ISBN Enable ISBN Disable* - 32 -...
Page 33
Programming Program 9 - 13. UPC / EAN Supplements Addenda 2 Digit Enable Addenda 2 Digit Disable* Addenda 5 Digit Enable Addenda 5 Digit Disable* ISBN Addenda Enable ISBN Addenda Disable* Space Separator Enable Space Separator Disable* Transmit if Present Must Present - 33 -...
Programming Program 12. Beep tones None Medium High* Beep duration short Beep duration medium Beep duration long Beep tone adjust Example: If beep tone of 230us is required, scan “Program“ pa “ Beep tone adjust“ “2“ “3“ “ Beep tone adjust“ “End“. Power on beep Enable * Power on beep Disable - 37 -...
Programming 15. Set max. & min. Length Set Max & Min Code 39 (1~64) Code 128 (4~64) Code 93 (4~64) Codabar (4~64) I 2 of 5 (4~64) S 2 of 5 (4~64) D 2 of 5 (4~64) Example: If max Length of code 39 isto be set 15 digits, scan “Program“ “Set Max &...
Page 41
Programming Program M 2 of 5 (4~64) Code 3 of 5 (6~7) MSI/Plessey (4~64) Code 11 (4~64) China postage (6~64) - 41 -...
Programming 18. Show status Display the edition Information (If want to display the edition Information, please scan “Program“ “Display the edition Information“ “End“) Reserved1 Reserved2 Reserved3 Reserved4 Reserved5 Reserved6 Reserved7 - 44 -...
Appendix 19. Appendix 19 – 1. Pin assignment RJ45 connector RJ45 pins Function Barkod Tx (TTL) Barkod Rx (TTL) PC D+ (USB) PC D- (USB) +5V DC - 45 -...
Page 46
Appendix Note: For LBR100 must only use specificated cabels for connecting which are inside the package. LBR100U – USB A tip to RJ45 LBR100R – SUB DB9 tip na RJ45 with dc connector Connector for external supply (Regulated +5Vdc / 300mA)
Page 47
+5V DC Note: Power supply of Bacode Scanner LBR100, AC/DC adapter +5Vdc/300mA, plug on DC connector which is placed on SUB DB9 connector housing. Pin 9 on SUB DB9 connector give's +5V. Some Electronic cash registers provide +5V on pin 9 of the serial port connector, in that case the AC/DC is not needed.