Advertisement
i
V Configuration
Wake up interval (battery mode)
Available settings: 0 - 16777214 (seconds)
Default setting: 4 000 (each 66 minutes)
Fig. 1 - Door / Window Sensor icon
in the Home Center controller
Defines a time period, in seconds, by which a Fibaro Door/Window
Sensor will perform a "Wake up" instruction - communicate with
main controller, update parameters, update software. Fibaro
Doow/Window Sensor will wake up each defined time interval and
will always attempt to connect with the main controller, without
retrying if connection fails (this preventing a battery from
discharging when the Sensor is used at the range limit, in case of
the main controller's breakdown, or in case the sensor is taken
away from the main controllers range). This parameter is relevant in
case of battery operation - higher Wake up interval means the
Sensor communicates less often saving a battery. After successful
communication attempt, a sensor will go into standby mode, update
parameters or will enter a software update mode. After failed
communication attempt, a sensor will go into standby mode until
another time interval will have elapsed.
Wake Up Interval set to 0 disables the sending frame WAKE UP, in
such configuration it is needed to manually wake the device up by
tripple pressing the TMP button which send a NODE INFO frame.
Fig. 2 - DS18B20 temperature sensor icon
in the Home Center controller
The Door / Window Sensor offers a wide range of advanced
Sensor used without a DS18B20 sensor, or used with a switch
settings. The parameters listed below are available in the
connected to IN input, will be represented by single icon. After the
Fibaro configuration interface.
DS18B20 temperature sensor has been connected, temperature
sensor icon will be displayed.
In order to configure the Fibaro Door / Window Sensor (using the
Home Center 2 controller) go to the device options by clicking on
the icon:
CAUTION
i
If a temperature sensor icon is not displayed
Next, select the device options tab.
despite the fact the sensor itself has been
connected, or if the temperature readings are
incorrect, inspect the connections on the 1-wire
Device parameters:
bus, in particular the connection between sensor
outputs and the line, and the total length of the bus
wire which should not exceed 30m.
Parameter no. 1
Input IN alarm cancellation delay.
Additional delay after an alarm from input IN has ceased. The
parameter allows user to specify additional time, after which the
input IN alarm is cancelled once its violation has ceased.
IV Association
Default value: 0
Available parameter settings: 0 – 65535 s
Association allows the Fibaro Door/Window Sensor to directly
Parameter size: 2 [byte]
control another device in the Z-wave network, e.g. Dimmer, Switch
(On-Off), Roller Shutter or trigger scenes (scene control is only
Parameter no. 2
possible via the Home Center 2 controller).
Status change signalled by LED.
Default setting: 1
CAUTION
i
Association allows for direct transmission of control
Available parameter settings:
commands between devices and takes place without
0 - LED turned Off,
the participation of the main controller. Owing to this
1 - LED turned On.
mechanism
the
Door/Window
Sensor
may
communicate with devices even if the main controller
Parameter size: 1 [byte].
is completely destroyed, e.g. in the event of a fire.
Parameter no. 3
Type of IN input.
The Fibaro Door/Window Sensor supports three association
Default value: 0 – INPUT_NC (Normal Close)
groups.
Available parameter settings:
Group I is assigned to input IN1 (and the magnetic sensor).
0 – INPUT_NC (Normal Close)
Sending BASIC SET or ALARM command frames.
1 – INPUT_NO (Normal Open)
2 – INPUT_MONOSTABLE
Group II is assigned to TMP button. Once the button is released,
3 – INPUT_BISTABLE
ALARM GENERIC frame is sent to associated devices.
Parameter size: 1 [byte].
Group III reports on the condition of the device, only one device
may be assigned to the group (main controller, by default).
The Fibaro Door/Window Sensor allows for control over 5 devices
Parameter no. 5
per group, out of which 1 field is reserved for the network controller.
Type of control frame transmitted for association group 1, activated
In order to add an association (with the use of the Home Center 2
via IN input. The parameter allows you to specify the type of an
alarm frame or to force control frames transmission (BASIC_SET)
controller) go to device options by clicking this icon:
Default value: 255 – BASIC SET
Select the device options tab. Next specify which devices will be
Available parameter settings:
associated, and to which association groups. Sending of
1 – ALARM SMOKE frame
configuration commands to associated devices might take up to a
2 – ALARM CO frame
few hours, depending on previous devices settings and the number
3 – ALARM CO2 frame
of devices within the network.
4 – ALARM HEAT frame
5 – ALARM WATER frame
255 – Control frame BASIC_SET
Parameter size: 1 [byte].
Parameter no. 7
Value of the parameter specifying the forced level of dimming/ope-
CAUTION
ning roller blinds when "switch on"/"open" commands are sent to
Any new association order given while any
devices from association group no.1.
association commands are already being sent to
devices, cancels previous one.
In case of alarm frames an alarm priority is specified.
Default value: 255
Possible parameter settings: (1 – 99) and 255
Value of 255 makes it possible to activate a device. In case of the
Dimmer module it means activating the device and setting it to the
previously stored condition, e.g. when Dimmer is set to 30%,
deactivated and then reactivated using 255 commend, it will be
automatically set to the previous condition i.e. 30%.
Parameter size: 1 [byte].
Parameter no. 9
Deactivating transmission of the alarm cancelling frame or the
control frame deactivating the device (Basic). It allows for disabling
the function of deactivating the device and cancelling alarms for
devices associated with IN input.
Default value: 0
Available parameter settings:
0 – for association group no. 1 information is sent
1 – for association group no. 1 information is not sent.
Parameter size: 1 [byte].
CAUTION
i
The parameter cancels alarms only. Information on
alarm violation or activation commands for devices
from association groups are always sent.
Parameter no. 10
Tamper alarm.
Default value: 1
0 - Tamper alarm cancellation inactive
1 - Tamper alarm cancellation active
Parameter size: 1 [byte]
Parameter no. 12
Sensitivity to temperature changes. The maximum acceptable
difference between the last reported temperature and the current
temperature read from the sensor. If the temperatures differ by the
set value or more, a report with the current temperature value is
sent to the device assigned to association group no. 3.
Default value: 8 [0,5
C]
o
Available parameter settings: 0 – 255 [0
To set an appropriate parameter value use the following formula:
x = delta T x 16 - for Celsius
x = delta T x 80 / 9 - for Fahrenheit
x = parameter value
delta T – maximum acceptable temperature gradient in Celsius or
Fahrenheit
If the value is set to 0:
- if the wake-up interval is set to 255 seconds, temperature report
will be sent according to the interval,
- if the wake-up interval is set to over 255, temperature report will be
sent each ca. 4 minutes.
Parameter size: 1 [byte].
Parameter no. 13
Sending an alarm or control frame (for IN input, depending on
parameter no.5 value), and TMP button alarm frame. The frame is
sent in "broadcast" mode,
information sent in this mode is not repeated by the mesh network.
Default value: 0
Available parameter settings:
0 – IN and TMP Broadcast mode inactive,
1 – IN broadcast mode active, TMP broadcast mode inactive
2 – IN broadcast mode inactive, TMP broadcast mode active
3 – IN and TMP broadcast mode active
Parameter size: 1 [byte].
CAUTION
i
If the "broadcast" mode of information transmission
is activated for a given channel, then transmission of
information in "singlecast" mode, i.e. to devices
assigned to the association group, for this channel is
deactivated.
Parameter no. 14
Scene activation functionality.
Default value: 0
Available parameter settings:
0 - functionality deactivated
1 - functionality activated
The device offers the possibility of sending commands compatible
with Command class scene activation. Information is sent to
devices assigned to association group no. 3
Controllers such as the Home Center 2 are able to interpret such
commands and based on these commands activate scenes, to
which specific scene IDs have been assigned. The user may
expand the functionality of a button connected to IN input by
distinguishing the sequence of it being pushed. For example:
double click would trigger the "goodnight" scene and triple click
would trigger the "morning" scene. To fully use the possibilities
offered by the parameter no.14 it is recommended to use a
momentary or a toggle switch (parameter no.3).
Scene ID is determined in the following manner:
IN input:
Switch from "off" to "on" ID10
Switch from "on" to "off" ID11
Remaining IDs are recognized correctly if the value of parameter
no.3 was set to 2
Holding down ID12
Releasing ID13
Double click ID14
Triple click ID15
Parameter size: 1 [byte].
i
CAUTION
Scene activation functionality may shorten the
battery life, even by 25%.
Parameter no. 15
READ ONLY Parameter - can not set values
The parameter value is automatically sent to the association group
III if the connected sensor DS18B20 four times mistakenly read the
temperature. In case of Wake Up Interval set for 4000 seconds
temperature sensor will be checked every 5 minutes.
0 - DS18B20 is working properly
1 - DS18B20 is not working properly
255 - No DS18B20 temperature sensor.
Parameter size: 1 [byte]
VI Additional Functionality
Alarm Frame Support.
The Fibaro System allows you to set the device's reaction to alarms
(reaction to SENSOR_ALARM_REPORT frame). The Fibaro
Door/Window Sensor sends alarm frames of different types,
depending on parameter's no. 5 settings. The user should declare
type of alarm frame for each connected sensor. For example, for a
smoke detector connected to IN input the user should declare the
o
C to 16
o
C] [32
o
F – 60,8
o
F]
type 1–ALARM SMOKE frame (value of 1 should be entered), to
ensure the remaining Z-Wave network devices recognize the
information on smoke detector alarm correctly.
VII Door / Window Sensor operation
The Fibaro Door/Window Sensor may be operated using:
• Any System compatible controller (e.g. Home Center 2)
• Cellular phone (e.g. iPhone or phones from other manufacturers,
with the proper control application)
• PC, with the use of an Internet browser,
• Tablets (e.g. iPad)
• Using the TMP button, located inside the housing.
VIII Procedure to be followed in case of interference
The Device does not react to a programmed transmitter:
• Make sure the maximum range has not been exceeded and there
are no obstacles along the signal path containing metal surfaces,
i.e. to all devices within range -
e.g. metal cabinets, Ferro concrete ceiling, load bearing walls, etc.
• Make sure the device is not in the learning mode.
• Alternately repeat the programming process.
IX Guarantee
1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.
(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1;
60-421 Poznan, entered in the register of the National
Register kept by the District Court in Poznań, VIII Economic
Department of the National Court Register, no. 370151, NIP
7811858097, REGON: 301595664.
2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
3. During the Guarantee period, the Manufacturer shall remove any
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
Device with new or regenerated components, that are free of
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which
shall be free of any defects and its condition shall not be worse than
the original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different
device having technical parameters similar to the faulty one. Such
activity shall be considered as fulfilling the obligations of the
Manufacturer. The Manufacturer shall not refund money paid for the
device.
5. The holder of a valid guarantee shall submit a guarantee claim
through the guarantee service. Remember: before you submit a
guarantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved
remotely, saving time and money spent to initiating guarantee
procedure. If remote support is insufficient, the Customer shall fill
the guarantee claim form (using our website - www.fibargroup.com)
in order to obtain claim authorization.
When the guarantee claim form is submitted correctly, the
Customer shall receive the claim confirmation with an unique
number (Return Merchandise Authorization -RMA).
6. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
number (RMA-number).
7. When the guarantee claim form is submitted correctly, a
representative of the Authorised Guarantee Service (hereinafter as
"AGS") shall contact the Customer.
8. Defects revealed within the guarantee period shall be removed
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Device was kept by AGS.
9. The faulty device shall be provided by the Customer with
complete standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
process shall be equal to the guarantee period of the original
device. The guarantee period of the replaced part shall not be
extended.
11. Costs of delivering the faulty device shall be borne by the
Customer. For unjustified service calls, the Service may charge the
Customer with travel expenses and handling costs related to the
case.
12. AGS shall not accept a complaint claim only when:
• the Device was misused or the manual was not observed,
• the Device was provided by the Customer incomplete, without
accessories or nameplate,
• it was determined that the fault was caused by other reasons than
a material or manufacturing defect of the Device
• the guarantee document is not valid there is no proof of purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
14. The guarantee shall not cover:
• mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);
• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance,
force majeure, unforeseen accidents, theft, water damage, liquid
leakage, battery spill, weather conditions, sunlight, sand, moisture,
high or low temperature, air pollution;
• damages caused by malfunctioning software, attack of a
computer virus, or by failure to update the software as recommen-
ded by the Manufacturer;
• damages resulting from: surges in the power and/or telecommuni-
cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
• damages caused by using accessories not recommended by the
Manufacturer
• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;
• damages caused by Customer's failure to provide maintenance
and servicing activities defined in the operating manual;
• damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
• defects caused by operating faulty Device or accessories.
15. The scope of the guarantee repairs shall not include periodic
Court
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
agreement.
This Device may be used with all devices
i
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.
Any device compatible with Z-Wave may be added
to Fibaro system.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR
TV
INTERFERENCE
CAUSED
BY
UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Legal Notices
All information, including, but not limited to, information regarding the
features, functionality, and/or other product specification are subject
to change without notice. Fibaro reserves all rights to revise or
update its products, software, or documentation without any
obligation to notify any individual or entity.
Fibaro, Fibar Group logo, and Fibaro Door Window Sensor are
trademarks of Fibar Group Sp. z.o.o. All other brands and product
names referred to herein are trademarks of their respective holders.
Disclaimer
The information contained herein is provided in connection with
Fibaro products. No license, expressed or implied by estoppel or
otherwise, to any intellectual property rights is granted by this
documents.
This documentation may contain references to third-party sources of
information, hardware or software, products or services ("collectively
the "Third-Party Products or Services"). Fibaro does not control the
Third-Party Products or Services and is not responsible for any
Third-Party Products or Services.
Except as provided above or except to the extent prohibited by
applicable law, Fibaro shall not be liable for any incidental or
consequential damages caused by the breach of any express or
implied warranty. Fibaro assumes no liability whatsoever, and Fibaro
disclaims any express or implied warranty, relating to the sale and/or
use of the Fibaro products, including, but to limited to, liabilities
and/or warranties relating to fitness for a particular purpose,
merchantability, and/or infringement of any patent, copyright and/or
other intellectual property right.
Except to the extent prohibited by applicable law, Fibaro's liability
shall not exceed the price paid for the Fibaro products from direct,
indirect, special, incidental or consequential damages resulting from
the sue of the products, its accompanying software, or product
specifications, manuals, installation guides and/or any other
documentation.
Some states, provinces or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or other limitations
on warranties, so the above limitations or exclusion may not apply to
you. You may also have other rights that vary from state to state or
province to province.
FIBARGROUP
FIBARO
In case of any technical questions contact customer service centre in
your country.
www.fibaro.com
Advertisement
