1. Manuals
  2. Brands
  3. Citrix Manuals
  4. Network Hardware
  5. NetScaler 9010 Platform
  6. Quick start manual

Citrix NetScaler 9010 Platform Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Citrix NetScaler
Quick Start Guide: 9010 Platform
Citrix
NetScaler
9.1
®
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NetScaler 9010 Platform and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Citrix NetScaler 9010 Platform

Summary of Contents for Citrix NetScaler 9010 Platform

  • Page 1 Citrix NetScaler Quick Start Guide: 9010 Platform Citrix NetScaler ® ®...
  • Page 2 Plug the NetScaler equipment into an outlet on a different circuit from your equipment. (Make sure the NetScaler equipment and your equipment are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Citrix Systems, Inc., could void the FCC approval and negate your authority to operate the product.

  • Page 3: Before You Begin

    Quick Installation and Configuration Welcome to the Citrix NetScaler Application Delivery product line. Please take a minute to review the following instructions before proceeding with the installation of the Citrix NetScaler 9010 appliance. If you require further explanation of any item covered in this document, please see the NetScaler Hard- ware Installation and Setup Guide.

  • Page 4: Configuration Requirements

    Figure 2 The Citrix NetScaler 9010, Back Panel Configuration Requirements Once the appliance is rack mounted, you will need the following information to complete the initial setup: • The NetScaler IP (NSIP) address is the management IP address of the appli- NetScaler IP address: ance.

  • Page 5: Installation

    Fig- ure 3 illustrates the steps involved in mounting the Citrix NetScaler appliance to a rack. Figure 3 Rack Mounting a Citrix NetScaler Appliance Appliance Precautions •...
  • Page 6 Rack-rail hardware described earlier should be used instead. Installing SFP Transceivers The Citrix NetScaler 9010 SFP base system is shipped with four SFP (Small Form Factor Pluggable) network ports. However, the actual number of modules you receive is dependent on the port configura- tion purchased.
  • Page 7 LCD on the front of the NetScaler will illuminate after starting, and the LCD will indicate the operational status of the appliance. Figure 6 Connecting a Citrix NetScaler Appliance to a Power Source If you wish to update to the latest release of the system software before proceeding, see the Note NetScaler Migration Guide.
  • Page 8 Electrical Safety Precautions Basic electrical safety precautions should be followed to protect yourself from harm and the appliance from damage. • Be aware of the location of the emergency power off switch to disconnect the electrical outlet. If an electrical accident occurs, you can quickly remove power from the appliance. •...

  • Page 9: Setting Up Connectivity

    Setting Up Connectivity Before you can configure and manage the appliance, you will need to connect it to a management workstation or network. To do this, use any one of the following methods. • Use the default IP address to connect to the configuration utility. •...
  • Page 10 add ns ip 10.102.29.61 255.255.255.0 -type mip add route 0.0.0.0 0.0.0.0 10.102.29.1 set system user nsroot administrator save ns config reboot Note For information about deploying a high availability (HA) pair, see the NetScaler Networking Guide.

  • Page 11: System Specifications

    System Specifications The following table summarizes the specifications of the Citrix NetScaler 9010. Specifications 9010 Processor 1 single-core Memory 2 GB Number of Power Supplies Power Supply input voltage & 100-240 AC, 47-63Hz frequency Maximum Power Consumption 500 W Weight (lbs.)

  • Page 12: Additional Information

    NetScaler for the first time. Includes hands-on labs that covers commonly used features. • Citrix NetScaler Migration Guide. Migration instructions for setting up a new version of a NetScaler with a list of all new and deprecated commands and parameters, APIs, SNMP OIDs, and log mes- sages.

  • Page 14: Contact And Support Information

    Contact and Support Information : 800-4-CITRIX (800-424-8749) (United States and Canada only) Phone For country-specific numbers, visit the Support section at: http://www.citrix.com/ http://support.citrix.com/ http://mycitrix.com/ Customer Support Web Site nsdocs_feedback@citrix.com Documentation Feedback...

Table of Contents