1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Car Receiver
  5. AVX-7300
  6. Installation manual

Pioneer AVX-7300 Installation Manual

Pioneer avx-7300 car audio video system
Hide thumbs Also See for AVX-7300:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
AVX-7300
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
Le code de couleur des câbles utilisé pour ce produit est
nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.

Advertisement

Table of Contents
loading

Related Manuals for Pioneer AVX-7300

Summary of Contents for Pioneer AVX-7300

  • Page 1 AVX-7300 This product conforms to new cord colors. Los colores de los cables de este producto se confor- man con un nuevo código de colores. Dieses Produkt entspricht den neuen kabelfarben. Le code de couleur des câbles utilisé pour ce produit est nouveau.

  • Page 2: Table Of Contents

    Contents Connecting the Units ........ 2 Installation ..........8 Connecting the Power Cord DIN Front/Rear-mount ........8 When Connecting the Multi-Channel AV DIN Front-mount ..........8 Master Unit Installation with the rubber bush When Connecting the Navigation Unit DIN Rear-mount ..........10 Installation using the screw holes on the side of the unit Installing the Voice Guidance Speaker ..

  • Page 3: Connecting The Units

    Connecting the Units Note: • This unit is for vehicles with a 12-volt battery and • If this unit is installed in a vehicle that does not negative grounding. Before installing it in a recre- have an ACC (accessory) position on the ignition ational vehicle, truck, or bus, check the battery switch, the red lead of the unit should be connect- voltage.

  • Page 4: Connecting The Power Cord

    Connecting the Units Connecting the Power Cord Yellow (video input) 15 cm (VIDEO INPUT) Orange/white Fuse resistor To lighting switch terminal. Fuse resistor To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Yellow Fuse holder To terminal always supplied with power regardless of ignition switch position.
  • Page 5 Connection method Clamp the parking brake switch power supply side This Product lead. 2. Clamp firmly with needle-nosed pliers. Note: • The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer. Light green Used to detect the ON/OFF status of the parking brake.

  • Page 6: When Connecting The Multi-Channel Av Master Unit

    Connecting the Units When Connecting the Multi-Channel AV Master Unit AV cable (supplied with the Multi- RGB cable Multi-Channel AV Channel AV Master Unit) (supplied with the Multi- Master Unit (e.g. AVM-P9000R) Channel AV Master Unit) (sold separately) Gray Green Red (Right) White (Left) Yellow...
  • Page 7 Connection box (supplied with the DVD Navigation Unit) Green DVD Navigation Unit (e.g. AVIC-9DVD) (sold separately) To video output To audio outputs Voice guidance speaker RCA cables (sold separately) (supplied) This product Not used. 40 cm Black DVD player (e.g. SDV-P7) (sold separately) Yellow (front video output)

  • Page 8: When Connecting The Navigation Unit

    Connecting the Units When Connecting the Navigation Unit To audio inputs of car stereo To audio outputs Connection box (supplied with the DVD Navigation Unit) RCA cable (sold separately) DVD Navigation Unit (e.g. AVIC-9DVD) (sold separately) To video output Green Voice guidance speaker RCA cable (supplied)

  • Page 9: Installation

    Installation Note: • Before finally installing the unit, connect the • If installation angle exceeds 30° from horizontal, wiring temporarily, making sure it is all connect- the unit might not give its optimum performance. ed up properly, and the unit and the system work (Fig.
  • Page 10 Installation 2. Install side brackets. (Fig. 7) Side bracket Flush surface screw (5 ´ 6 mm) Fig. 7 3. Fastening the unit. (Fig. 8) As a rule, secure with side brackets (large). Holder After inserting the holder into the dash- board, then select the appropriate tabs according to the thickness of the dash- Dashboard...

  • Page 11: Din Rear-Mount

    7 When the installation space is not very deep When installing in a shallow space, secure with side brackets (small). In this case, stick conceal tape on parts that protrude from the dashboard. Holder After inserting the holder into the dash- board, then select the appropriate tabs according to the thickness of the dash- Dashboard...
  • Page 12 Installation 2. Fastening the unit to the factory radio mounting bracket. (Fig. 11) (Fig. 12) Select a position where the screw holes of the bracket and the screw holes of this product become aligned (are fitted), and tighten the screws at 2 places on each side. Use any of binding screws (4 ´...

  • Page 13: Installing The Voice Guidance Speaker

    Installing the Voice Guidance Speaker Precaution: • Do not install on the dashboard where it may be subjected to direct sunlight. High temperatures may result in damage to the unit. • Install within the transmission range of the remote control signal. Stick the supplied velcro tape to the back of both the voice guidance speaker and the center console, and attach them.
  • Page 14 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada Copyright © 2001 by Pioneer Corporation. TEL: (905) 479-4411 All rights reserved. PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Publication de Pioneer Corporation. San Lorenzo 1009 3er. Piso Desp. 302 Copyright © 2001 Pioneer Corporation.

Table of Contents