Subscribe to Our Youtube Channel
Related Manuals for Optocore DD8RP
Summary of Contents for Optocore DD8RP
- Page 1 Operating Manual for OPTOCORE DD8RP REPEATER / MEDIA CONVERTER MODULE © Copyright 2007 All rights reserved OPTOCORE GmbH Lisbergstr. 7 81249 Munich Germany DD8RP Operating Manual Rev. 1.0...
-
Page 2: Important Safety Instructions
• Never switch on power amplifiers before the complete system is stable and the level meters of the OPTOCORE CONTROL software indicate a normal level. • Do not place this device on an unstable table, tripod, cart, etc. The device may fall, causing serious damage to the device, and a risk of injury. -
Page 3: Purchaser Information
Keep the rear of the rack open during operation. Do not set up the device close to equipment producing a lot of heat, for example power-amplifiers. Leave enough space (minimum ½ RU) to any heat emitting device. A DD8RP may be placed on top or beneath other Optocore products, except DD32, without additional space. - Page 4 The device may not be serviced, altered or modified without authorization of Optocore or an Optocore authorized distributor / dealer. Only qualified service personnel may carry out repair and maintenance work. The warranty will be voided if unauthorized manipulation occurred.
-
Page 5: Ce-Conformity
CE-Conformity This document confirms that the product DD8RP bearing the CE (Communauté Européenne) label meets all requirements in the EMC directive 2004/108/EG laid down by the Member States Council for adjustment of legal requirements. Furthermore the product complies with the rules and regulations of the low-voltage directive 2006/95/EG. -
Page 6: Table Of Contents
DD8RP REPEATER / MEDIA CONVERTER MODULE Table of Contents Important Safety Instructions............................2 Purchaser Information ..............................3 CE-Conformity................................5 Eye Safety................................5 Device Description ..............................7 Front Panel................................8 Rear Panel ................................8 Device Details ................................9 LINK Ports ..............................9 Power Supply..............................9 Connectors and Cables............................9 Starting Up ................................10 Hardware Connection .......................... -
Page 7: Device Description
The DC power supply is compatible with battery packs, UPSs (Uninterruptible Power Supply) or standard AC adapters. Due to SMD production the DD8RP fulfills the demand of highest digital standards occupying only one rack unit of a 19" rack. The FPGA (field programmable gate array) based concept of the internal logic circuitry permits updating of the hardware via the units remote ports, ensuring a continual state-of-the-art device. -
Page 8: Front Panel
Independent LC-type optical interface, equipped with SFP transceivers. Type LINK 1 … 4: of transceivers depend on costumer’s order. Input for DC 12V / 1A power supply POWER 2: Mains input for AC power supply 1 (100 … 240 V) POWER 1: DD8RP 8 / 15 rev. 1.0... -
Page 9: Device Details
The DD8RP is not limited to be used in Optocore networks. It can operate in all sorts of networks no matter which protocol is the base of the data transmission. The four LINKS are functioning totally independent; so one LINK can serve in an Optocore network, the next one in a 1 Gbit-Ethernet and the others in completely different networks. -
Page 10: Starting Up
The DD8RP is functioning independent of the format and structure of the connected devices. So no software configuration is necessary, no ID has to be set and there is no limitation of the number of DD8RP implemented in the network. -
Page 11: Connection Tables
Power Internally Channel Bridged Use 1-modem cable, male – female, to +5VS connect to PC 1, 4, 6 7, 8 Locking system acc. to 4-40 UNC D-Sub-9- female Pin-out USB-Port Channel VBUS USB device-connector DD8RP 11 / 15 rev. 1.0... -
Page 12: Technical Specifications
0,6 VA – idle, plus 0,45 / 0,6 VA per SFP installed (multimode / monomode) Power consumption Electronic fuse Protection circuit 4 pole XLR male 12 V device connector 4 pole XLR female (e.g. Neutrik NC4FX) 12 V cable connector Via surface and ventilation-slits on both side Cooling DD8RP 12 / 15 rev. 1.0... -
Page 13: Dimensions And Weight
[inch] Front-plate, Front-elements, Handles: Add 6 [0.24] 483 [19] Weight 2.0 kg ≡ 4.4 lbs Modifications that serve the purpose of technical improvement of the device may be carried out without prior notification. DD8RP 13 / 15 rev. 1.0... -
Page 14: Warranty And Liability
This warranty covers the original purchaser only and is not transferable. Valid evidence for warranty is the official Optocore invoice issued by the distributor / dealer. Optocore will, at its discretion, repair or replace a defective product, providing that the defect has appeared under normal operating conditions. -
Page 15: Company Information
Company Information Mailing Address: OPTOCORE GmbH Lisbergstr. 7 D-81249 Munich Germany Telephone: +49 – (0)89 – 8999640 Facsimile: +49 – (0)89 – 89996455 Internet: www.optocore.com Email: DD8RP 15 / 15 rev. 1.0...
Need help?
Do you have a question about the DD8RP and is the answer not in the manual?
Questions and answers