Related Manuals for Magenta MultiView II DVI-Rx-1K
Summary of Contents for Magenta MultiView II DVI-Rx-1K
- Page 1 MultiView II DVI-Rx-1K Receiver Installation and User Guide Version 1.00 2791 Circleport Drive, Erlanger, KY 41018, USA. Americas: 859-282-7303 EMEA: +44 (0) 1843 873322 Email: tech.usa@tvone.com www.tvone.com...
- Page 2 Manual Copyright Notice This document and the Magenta Research products to which it relates, and the copyright in each, is the intellectual property of tvONE, ©2014. Neither the document nor the products may be reproduced by any means, in whole or in part, without the express prior written permission of tvONE.
- Page 3 Regulatory Compliance Statements FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
- Page 4 Precautions Precautions Safety Instructions ● English This symbol calls attention to important information. This symbol alerts the user of important maintenance (or servicing) and operating information. This symbol alerts the user to the presence of un-insulated dangerous voltages or other conditions in, or around, the product enclosure.
-
Page 5: Table Of Contents
Precautions Table of Contents Page Chapter 1 Specifications ..........................1 Chapter 2 About this Manual ........................2 Chapter 3 Product Overview ........................3 Front Panel Interfaces ..................... 3 Rear Panel Interfaces ..................... 4 Chapter 4 Twisted-pair Cable Compatibility ....................5 Chapter 5 Installation .......................... -
Page 6: Chapter 1 Specifications
Specifications Chapter 1 Specifications The following table lists the general specifications of the MVII-DVI-Rx-1K. Table 1: MVII-DVI-Rx-1K General Specifications Item Description The MVII-DVI-Rx-1K receiver MUST be used with a MVII-DVI-Tx transmitter. Use of Compatible transmitter any other MultiView transmitter will result in no displayed image at the receiver. 4 twisted-pair “FTP”... -
Page 7: Chapter 2 About This Manual
Connector Pin-outs (Chapter 7) Additional information (Appendices) The Magenta MultiView™ II family (MVII) of products introduces greater compatibility for handling HD video standards, as well as making nearly all user-configurable options “jumperless” via a digital front-panel user- interface. Compatiblity with MultiView transmitters: The MultiView-II DVI-Rx-1K receiver will only function correctly with a MVII-DVI-Tx transmitter as the source device. -
Page 8: Chapter 3 Product Overview
Product Overview Chapter 3 Product Overview The MVII-DVI-Rx-1K is a video receiver that is compatible with the MVII-DVI-Tx transmitter, and many legacy MultiView products – contact Technical Support with compatibility questions. It extends an analog video signal over standard twisted-pair “FTP” type cable. There are user-configurable settings for video, audio, and serial options which can be controlled from the front panel. -
Page 9: Rear Panel Interfaces
Product Overview Rear Panel Interfaces The rear panel of the MVII-DVI-Rx-1K has the following ports: DB9 serial port Auxiliary (optional, on signals SAP model only) UTP (link) DC power UTP (link) Video output output port input port input port to display Figure 2: MVII-DVI-Rx-1K Rear Panel Interfaces MultiView™... -
Page 10: Chapter 4 Twisted-Pair Cable Compatibility
CAT6 cable, due to the manufacture method, can exhibit much greater skew than standard CAT5/5e. Please contact tech-support for assistance. Cabling for the Magenta MultiView™ Series must be pinned to the TIA-EIA T568B wiring specification. We also highly recommend that all cables be pre-terminated and tested. Cables terminated on-site or in an existing infrastructure should be tested before use to ensure compliance with the TIA-EIA T568B specification. -
Page 11: Chapter 5 Installation
Prerequisites Depending on the specific installation requirements, some common tools (screwdrivers, nut-drivers) and related hardware (mounting screws) might be required. These are not provided with Magenta products. The following items might be necessary, which are available from Magenta Research: ... - Page 12 Installation To install a MultiView-II DVI-Tx transmitter: Connect the source video to the Magenta MultiView™ DVI-Tx transmitter’s video input port, which is a DVI-D connector labeled DVI-IN. If desired, attach a local monitor to the DVI-D connector labeled LOCAL OUT (if available).
- Page 13 Installation To install the MVII-DVI-Rx-1K receiver: Connect the DVI OUT connector to the display. Connect any audio and/or serial cables to the (AUX I/O) and (IOIO) connectors, depending on the specific model of receiver you are installing. Please refer to the –A, -S or –SAP option descriptions for more information.
-
Page 14: Adjustments
EQ. The EQ/SKEW indicators 1-8 will change accordingly to show (in “bar-graph” form) 0 to 100% of the available EQ adjustment range. For best results, use the Magenta EQ/Skew test pattern image if possible. A test pattern image and video instructions is available at http://www.magenta-research.com/test. -
Page 15: Skew Compensation Settings
EQ/SKEW indicators 1-8 will change accordingly to show (in “bar-graph” form) 0 to 100% of the available SKEW adjustment range (0 to 65nSec). For best results, use the Magenta EQ/Skew test pattern image if possible. A test pattern image and video instructions is available at http://www.magenta-research.com/test. -
Page 16: Configuration Settings
Installation Configuration Settings There are a number of configurable operating parameters, and the factory-default settings should work for most applications. However, some applications might require slight configuration changes. This section describes how to configure the following settings: Config-mode, LEDs 1-3: pair settings ... -
Page 17: 4Th Pair Settings (Led1-3)
Installation 5.7.2 4th Pair Settings (LED1-3) The MVII-DVI-Rx 1K provides several options for using the 4 -pair signals (pairs 1-3 are generally used for video). The factory-default settings support analog audio (L+R summed) on the 4 -pair. Note that the connected MultiView transmitter and any daisy-chained receivers must be configured with a matching 4 -pair -pair signal will not work as expected –... -
Page 18: Th Pair Termination Settings (Led4)
Installation 5.7.3 4 Pair Termination Settings (LED4) The MVII-DVI-Rx-1K receiver provides settings for 4 pair termination: ON or OFF. This setting has an effect only for “-S”, “-A” and S/PDIF operating modes. -pair setting if an option board is installed – since this setting is ignored. Note: It is not possible to access the 4 ... -
Page 19: Chapter 6 Troubleshooting
Troubleshooting Chapter 6 Troubleshooting In most cases, nearly every issue with the MultiView™ video system can be resolved by checking the twisted- pair cable termination and making sure that it’s pinned to the TIA/EIA 568B wiring specification. However, there may be other problems that cause the system to not perform as it’s designed. The following table lists the most common installation errors and their solutions. -
Page 20: Chapter 7 Connector Pinouts
Connector Pinouts Chapter 7 Connector Pinouts DVI-D connector pinout: Pins #1-8 Key holes, to prevent wrong type of cable Pins #9-16 being plugged in Pins #17-24 DVI (Digital Visual Interface) is a robust and popular video interface standard that can include digital and analog options in the same connector (the “DVI-I”... - Page 21 Connector Pinouts Auxiliary I/O (AUX-I/O) Connector Pinout Pin #1 Pin #4 Figure 7: 4-pin Phoenix Connector Pinout Table 5: Auxiliary I/O (4-pin Phoenix) Pin Usage (SAP) SPDIF PIN# Simplex Audio Audio Audio Serial Left Left Signal + (SIG1) Channel Channel Ground Ground ground...
- Page 22 Connector Pinouts Serial port (IOIO) Connector Pinout If the receiver is an -SAP version, then the serial interface will be provided on the “IOIO” connector. This is a DB9-M type serial connector, configured to look like a standard 9-pin “DTE” serial port. Therefore, in most applications a straight through serial cable or adapter-plug (DB9-Female-to-Male) is used to connect an external serial device (for example, a display’s serial control port) to the receiver.
- Page 23 Connector Pinouts RJ45 (MultiView Link) Wiring Standard Figure 9: T568B Category Cable Wiring Standard Table 7: T568B wiring for RJ-45 plug PIN # COLOR PAIR White / Orange Stripe Pins on plug Orange Solid face (socket is reversed) White / Green Stripe Blue Solid White / Blue Stripe Green Solid...
-
Page 24: Dc Power Connector
Connector Pinouts DC Power Connector Magenta provides ready-to-use power supplies for MultiView™ II products. However, if there is a reason a substitute power supply must be used, then the following information is important for maintaining product reliability and performance: Magenta AC/DC Power supply output rating: Regulated +5VDC @ 2.6Amps. -
Page 25: Appendix A Supported Video Formats And Features
Supported Video Formats and Features Appendix A Supported Video Formats and Features The following video formats are supported by the MVII-DVI-Tx and MVII-DVI-Rx-1K (combined) link. This table represents the contents of the EDID information stored in the transmitter. Table 8: MultiView™ II DVI-Tx + DVI-Rx-1K Supported Video Formats and Features Format/Feature Description 640x480p/59.94&60Hz/24... -
Page 26: Appendix B (Sap) Option Module Settings
(SAP) Option Module Settings Appendix B (SAP) Option Module Settings The SAP option module allows a bi-directional session to be established between a SAP-equipped transmitter (MVII-DVI-Tx-SAP), and a specific SAP-equipped receiver even in a multiple-receiver daisy chain installation. The SAP transmitter devices (MVII-DVI-Tx-SAP for example) do not have address DIP-switches. The factory- default address of the transmitter is “0”. -
Page 27: Appendix C Pollable Serial Mode Address Chart
Pollable Serial Mode Address Chart Appendix C Pollable Serial Mode Address Chart ADDR Switch Settings ADDR Switch Settings ADDR Switch Settings ADDR Switch Settings MultiView™ II DVI-Rx-1K Installation and User Guide... - Page 28 Pollable Serial Mode Address Chart SAP Addressing chart, cont’d: ADDR Switch Settings ADDR Switch Settings ADDR Switch Settings ADDR Switch Settings MultiView™ II DVI-Rx-1K Installation and User Guide...
-
Page 29: Appendix D Mounting Kits
Mounting Kits Appendix D Mounting Kits The following table shows several kits available for mounting the MultiView™ II DVI-Rx-1K receiver. Table 9: MVII-DVI-Rx-1K Mounting Kits Mounting Kit # Description 2211054-01 Rigid-mount bracket. This mounts a single device to a surface (wall/desk/etc.). - Page 30 Mounting Kits Note: When installing MVII-DVI-Rx-1K receivers in an area susceptible to elevated operating temperatures (near the maximum specified operating temperature), it is important to give careful consideration to maintaining adequate air flow. Within a rack assembly, cable bundles and other equipment in the same rack can impede proper cooling.
- Page 31 Index About this manual, 2 procedure, 6 SAP Module Configuration, 6 Adjustments, 9 EQ setting, 9 Mounting kits, 24 Skew setting, 10 Option module settings Auxiliary I/O connector, 16 SAP option module, 21 Configuration Pollable serial mode -Pair Settings, 12 addressing chart, 22 -pair termination setting, 13 Precautions, iv...
- Page 32 NOTES: MultiView™ II DVI-Rx-1K Installation and User Guide...
- Page 33 2791 Circleport Drive, Erlanger, KY 41018, USA. Americas: 859-282-7303 EMEA: +44 (0) 1843 873322 Email: tech.usa@tvone.com www.tvone.com MultiView™ II DVI-Rx-1K Installation and User Guide...