Advertisement
Action
Display
Turn power ON/OFF
Press to turn power ON. Press and hold
1
for 2 seconds to turn power OFF.
Select accuracy
Press once to change current setting
(A beep confirms the selected volume.)
Select beeper volume
Press once to display current setting;
push again to scroll through options.
Select units of measure
Press once to display current setting,
additional pushes to scroll through options.
Select brightness of LEDs
+
Displayed for 3 seconds after power-up.
.
Press together to cycle the selection
Remarks
Initialization:
1. Test of LCD, LED and beeper
2. CAL: Calibration (3 sec.)
3. Unit is ready for use.
(Do not power up the unit in a laser beam
or strobe. If detected, the unit will display
"E200" and revert to the previous calibra-
tion.)
2
3
Accuracy in mm:
The selected unit of measure determines
the displayed deadband (accuracy).
0.5 1.0 2.0 5.0 10.0
The current accuracy is stored in memory
and will be retained when the unit is turned
off or when batteries are replaced.
(No symbol)
The current beeper
volume is stored in
Beeper
Beeper
Beeper
Beeper
memory and will be
Loud
Medium
Low
OFF
retained when the unit is
turned off or when bat-
teries are replaced.
The current unit of measure is stored in
mm - cm - in - frac - ft
memory and will be retained when the unit
is turned off or when batteries are replaced.
(No symbol)
The current brightness of LEDs
is stored in memory and will
be retained when the unit is
LEDs
LEDs
LEDs
turned off or when batteries are
Bright
Dim
OFF
replaced.
Action
Display
CAPTURE Function
A) Laserometer is in the laser beam and
the power is on
1 x quick
B) Laserometer is out of the laser beam
and power is on:
1.
1 x quick
2. Place the Laserometer in the beam.
(Example: Fasten it to a measuring rod,
bring the Laserometer into the laser beam.
You now have 5 seconds to plumb the rod
and get the reading captured.)
Special Menu Functions
Press switches
.
together for 2 sec
SENS
AVG
+
D.R.O
.
UNIT
FRC.R
.
ARRW
O.O.B.
GRD.A
.
A.S.O
.
How to change Menu functions:
TX.O.L
.
TX.O.B
. Transmitter Low Battery OFF*-RPS
INFO
1. Scrolling up or down.
Automatic Shutoff
A.S.O. (Automatic Shut Off):
2. Enter Change mode.
0.5 - After 30 Minutes*
OF - Off (Unit is permanently on.)
24 - 24 hour shutoff
.
3. Change selected items
Out-of-Beam Display
.
O.O.B. (Out-of-Beam Display):
4. Confirm change
Sequence to show direction to get back in
the laser beam (for 25 s)
5. To Exit.
or
ON - Out-of-Beam Display ON*
OF - Out-of-Beam Display OFF
Remarks
The current elevation read-
Press any switch to return to normal
ing will be held. A flashing
operation.
display will confirm the
.
reading has been captured
A short intermittent
+
beep (The beeper
will turn on to Low if
turned off.)
The beeper will
Press any switch to return to normal
+
chirp rapidly after
operation.
approximately 5
seconds to confirm
beam capture. A flashing
display will also indicate
the reading has been
captured
.
Change special Menu Functions only in the
(for 2 Sec., then SENS)
case of special job requirements!
Sensitivity of reception
Sensitivity Medium*-HighLow
SENS (Sensitivity):
Averaging algorithm Medium*High - Low
Numeric display ON*-OFF-.1mm
Selects reception sensitivity to laser and
Units of measure MM*-CM-IN-FRAC-FT
other light sources.
Fractional Reduction ON*-OFF
MD - Medium*: for most applications.
Arrow Display DB*(deadband)-PR (prop.)
Out-of-Beam Display ON*-OFF
HI - High: When laser beam is
Grade Alarm ON-OFF*
weak, or at very long distances.
Automatic shutoff 0.5h*-24h-OFF
LO - Low: If outside sources are
Transmitter Out-of-Level OFF*RPS
disturbing elevation readings
Information about the Laserometer
Grade Alarm
GRD.A. (Grade Alarm):
When turned ON, disables the audible
signal when on-grade. When moved out
of the on-grade deadband, the beeper
activates as normal:
ON - Alarm on (Solid beeper OFF)
OF - Alarm off (Solid beeper ON)*
* Default setting
For more information about special Menu
Function contact the manu-facturer,
importer or your local dealer
.
.
Advertisement
