Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Logic Controls SB-9090
Summary of Contents for Logic Controls SB-9090
- Page 1 SB-9090 All-in-One System SB-9090 All-in-One System...
-
Page 2: Table Of Contents
Contents Notice ...................... 3 Safety Information ................. 3 Caution on Lithium Batteries ..............3 Legislation and Weee Symbol ..............4 Package Contents ................... 4 System Assembly and Disassembly............5 Open the System ..................5 Replace HDD....................5 Security Screws..................6 Customer Display Installation..............7 Cash Drawer Installation.................8 MSR Installation..................10 Metal Stand Installation.................11... -
Page 3: Notice
Notice ‧ All Information in this manual may change without prior notice. ‧ To ensure safety operation of this product, please read the following menu carefully before using this product. Safety Information ‧ To disconnect the machine from the electrical power supply, turn off the power switch and remove the power cord plug from the wall socket. -
Page 4: Legislation And Weee Symbol
Legislation and Weee Symbol 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. -
Page 5: System Assembly And Disassembly
System Assembly and Disassembly 1. Open the System To access the inside system, you need to open the system first and the procedure of opening the system is as below: 2. Replace the Hard Drive 1) Slide out the back cover. 2) Remove the screw and pull out the hard drive. -
Page 6: Security Screws
4) Screw the round screws back on the hard drive tray and insert the hard drive tray into the system hard drive slot. 5) Fix the hard drive with screw on the system. Security Screws These are security screws and a screw driver for replacing the hard drive. -
Page 7: Customer Display Installation
3. Customer Display Installation 1) Put the panel on the flat table & open the I/O back cover of system. 2) Assembly the customer display hinge into the customer display slot and fasten two screws. 3) Connect the customer display into COM3 via the cable management slot and adjust COM3 voltage+12V in BIOS. -
Page 8: Cash Drawer Installation
Cash Drawer Installation You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Cash Drawer Pin Assignment Cash Drawer Controller Register. The Cash Drawer Controller use one I/O address to control the Cash Drawer. Register Location: A22h Attribute: Read / Write Size: 8bit... - Page 9 Bit 6: Reserved Bit 7: Reserved Note: Please follow the Cash Drawer control signal design to control the Cash Drawer. Cash Drawer Control Command Example Use Debug.EXE program under DOS or Windows98 Command Cash Drawer O A22 10 Opening O A22 00 Allow to close Set the I/O address A22h bit2 = 1 for opening Cash Drawer by “DOUT bit0”...
-
Page 10: Msr Installation
5. MSR Installation 1) Open the right side cover of system. MSR connection is supported on the right side. 2) Connect MSR and System connector, system connector supports PS/2 interface. 3) Fasten the MSR screw on system. -
Page 11: Metal Stand Installation
6. Metal Stand Installation... -
Page 12: Jump Settings
Jump Settings 1. Motherboard Layout Connector & Jumper Setting Mini Din 4P for Power Input Port Internal Power Input Connector RJ11 for Cash Drawer Port LAN1 RJ45 for LAN Port USB1, 2 USB dual stack for USB Port USB4, 5, 6, 7 USB Connector COM1 D-SUB 9 Pin for COM1 Port... - Page 13 COM4 COM4 Connector PS/2 for Keyboard Port SATA1 SATA 7 Pin for SATA1 Connector SATA2 SATA 7 Pin for SATA2 Connector SATA3 SATA 7 Pin for SATA3 Connector SPWR1, 2 Power Output for SATA HDD IDE1 PATA Connector LVDS1 LCD Connector VGA1 VGA Connector Card Reader Connector...
-
Page 14: Serial Port Pin 9 Mode Settings
Serial Port Pin 9 Mode Settings BIOS Main Menu When the BIOS Main Menu is displayed, the following items can be selected. Use the arrow keys to select items and the enter key to accept and enter the sub-menu. Enter System Overview Advanced Settings. - Page 15 Select Super I/O Configuration. Use this menu for set up super I/O configuration. Serial Port 1-4 Pin9 Mode. Enter into serial port 1- 4 Pin9 Mode and set up the options then select the serial port 1 Pin9 mode. Save and Exit...
-
Page 16: Appendix
Appendix Drivers Installation The shipping package includes a Driver CD. You can find every individual driver and utility that enables you to install the drivers in the Driver CD. Please insert the Driver CD into the drive and double click on the “index.htm” to pick up the models. You can refer to the drivers installation guide for each driver in the “Driver/Manual List”. -
Page 17: Specification
Specification Mechanical Dimensions 14.57” x 11.3” x 2.17” (W x H x D) Weight 9.92 lbs Mainboards Intel® Atom™ Processor D410 (Single Core) 1.66GHz with L2 Cache 512KB System Desktop Management Interface (DMI) Management Preboot Execution Environment (PXE) Wake on LAN (WoL) Advanced Configuration and Power Interface (ACPI) Memory 1 x SO-DIMM DDRII 667, up to 2GB... -
Page 18: Limited Warranty Policy
Limited Warranty Policy All SB-9090 feature a three-year-limited warranty with free change in the first year from the date of purchase. If product is determined to be defective, we will repair or replace the product with refurbished or remanufactured parts or components during the warranty period. - Page 19 SB-9090 All-in-One System...