Advertisement

SERVICE MANUAL
Ver 1.3 2003.11
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
D-A conversion
1-bit quartz time-axis control
Frequency response
+1
20 - 20 000 Hz
dB (measured by JEITA CP-
–2
307)
Output (at 4.5 V input level)
Line output (stereo minijack)
Output level 0.7 V rms at 47 kΩ
Recommended load impedance over 10 kΩ
Headphones (stereo minijack)
Approx. 5 mW + Approx. 5 mW at 16 Ω
(Approx. 0.5 mW + Approx. 0.5 mW
at 16 Ω)*
*For the customers in France
Optical digital output (optical output connector)
Output level: –21 - –15 dBm
Wavelength: 630 - 690 nm at peak level
Power requirements
For the area code of the model you
purchased, check the upper left side of the
bar code on the package.
• Two Sony NC-6WM rechargeable batteries:
2.4 V DC
Sony Corporation
9-873-379-04
2003K05-1
Personal Audio Company
C 2003.11
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism NEW
CD Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
• Two LR6 (size AA) batteries: 3 V DC
• AC power adaptor (DC IN 4.5 V jack):
US, Canadian, Taiwan models: 120 V, 60 Hz
AEP, French, E13 models: 220 - 230 V, 50/60 Hz
UK model: 230 - 240 V, 50 Hz
Australian model: 240 V, 50 Hz
E33, Korean, Tourist models: 100 - 240 V,
50/60 Hz
Hong Kong model: 220 V, 50/60 Hz
Chinese model: 220 V, 50 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
surface.)
Playing time varies depending on how the CD
player is used.
When using
G-PROTECTION
"1"
Two NC-6WM
19
(charged for
about 5 hours**)
External battery case
66
(two alkaline batteries***)
Rechargeable batteries
88
NC-6WM and
external battery case
(two alkaline batteries***)
*
Measured value by the standard of JEITA
(Japan Electronics and Information Technology
Industries Association).
** Charging time varies depending on how the
rechargeable battery is used.
*** When using Sony alkaline batteries LR6 (SG)
(produced in Japan)
D-EJ855
Canadian Model
Australian Model
Chinese Model
Tourist Model
Operating temperature
5°C - 35°C (41°F - 95°F)
Dimensions (w/h/d) (excluding
projecting parts and controls)
Approx. 135.0 × 18.2 × 135.0 mm
3
23
3
(5
×
× 5
in.)
8
32
8
Mass (excluding accessories)
Approx. 172 g (6.1 oz)
Supplied accessories
For the area code of the location in which you
purchased the CD player, check the upper left side
of the bar code on the package.
AC power adaptor (1)
Headphones/earphones with remote control (1)
Rechargeable batteries (2)
"2"
Battery carrying case (2)
Carrying pouch (1)
19.5
External battery case (1)
1
AC plug adaptor (1)*
1
*
Supplied with E33 and Tourist models
71
Design and specifications are subject to change
92
without notice.
• Abbreviation
E13: 220 - 230 V AC area in E model
E33: 100 - 240 V AC area in E model
PORTABLE CD PLAYER
US Model
AEP Model
UK Model
E Model
CDM-3325ES
DAX-25E

Advertisement

Table of Contents
loading

Summary of Contents for Sony D-EJ855

  • Page 1 ** Charging time varies depending on how the bar code on the package. rechargeable battery is used. *** When using Sony alkaline batteries LR6 (SG) • Two Sony NC-6WM rechargeable batteries: (produced in Japan) 2.4 V DC...
  • Page 2: Table Of Contents

    SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Servicing Notes

    D-EJ855 SECTION 1 SERVICING NOTES About CD-Rs/CD-RWs BEFORE REPLACING THE OPTICAL PICK-UP BLOCK Please be sure to check thoroughly the parameters as par the “Op- This CD player can play CD-Rs/CD-RWs recorded in the CD-DA tical Pick-Up Block Checking Procedures” (Part No.: 9-960-027- format*, but playback capability may vary depending on the qual- 11) issued separately before replacing the optical pick-up block.
  • Page 4 D-EJ855 SERVICE MODE 2. Operation in Service Mode When the Service mode is set, the LCD on the remote commander In the Service mode, this set can check the following. displays the following. 1. Service Mode Setting Method Remote commander LCD display To set the service mode, perform as follows.
  • Page 5 D-EJ855 Remote Commander LCD display 010001 (1 time) 040004 (4 times) (For the rest, turn the power off and then turn it on again) • [SOUND] button on remote commander Servo auto adjustment 4. Service Mode Releasing Method To release the service mode, perform as follows.
  • Page 6: General

    D-EJ855 SECTION 2 This section is extracted from instruction manual. GENERAL Getting started Remote control qs Display Locating the controls (pages 9, 11 - 15) For details, see pages in parentheses. CD player (front) qf x (stop) button (pages 8, 16) 1 EXT BATT (external battery)/ DC IN 4.5 V (external power...
  • Page 7: Disassembly

    D-EJ855 Ver 1.1 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. UPPER LID (M) SUB ASSY (Page 7) 3-3. CABINET (UPPER) SUB ASSY (Page 8) 3-4. MAIN BOARD, OPTICAL PICK-UP SECTION (CDM-3325ES) (Page 8) Note: Follow the disassembly procedure in the numerical order given.
  • Page 8: Cabinret (Upper) Sub Assy

    D-EJ855 3-3. CABINET (UPPER) SUB ASSY 2 four screws 2 three screws (B2) 3 claw (B2) knob (GPRO) 3 claw 1 screw (B2) 3 claw 4 cabinet (upper) sub assy 5 battery terminal board (relay) Note: On installation of cabinet (upper) sub assy, adjust the position of two switches (S802, S803) and two knobs (GPRO).
  • Page 9: Electrical Check

    D-EJ855 SECTION 4 ELECTRICAL CHECK Focus bias Check The CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias. Condition: • Hold the set in horizontal state. Precautions for Check 1. Perform check in the order given.
  • Page 10: Diagrams

    D-EJ855 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM – MAIN Section (1/2) – RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER IC601 DETECTOR WDCK DOUT DIGITAL DOUT (Page 11) WFCK D-RAM IC602 RFDC RFAC XTAO D0-D3 XTAI VCPU B+...
  • Page 11: Block Diagram - Main Section (2/2)

    D-EJ855 5-2. BLOCK DIAGRAM – MAIN Section (2/2) – B+ SWITCH VCC3 Q301 DOUT (Page 10) J301 OPTICAL TRANSCEIVER LINE OUT (OPTICAL) AOUTL AOUTR (Page 10) (LINE OUT JACK) MUTING Q303 J302 HEADPHONE AMP IC301 IN_L OUT_L IN_R OUT_R (Page 10)
  • Page 12: Block Diagram - Power Supply Section

    D-EJ855 5-3. BLOCK DIAGRAM – POWER SUPPLY Section – (Page 10) POWER CONTROL IC403 (2/2) PAPC (Page 10) SYNC SYNC (Page 10) SDTO DATA BATM1 (Page 10) CHARGING BATTERY BATM2 CLOCK VOLTAGE DETECTOR (Page 10) CHGSW CIRCUIT CHGMNT VLGO4 LINEAR...
  • Page 13: Note For Printed Wiring Boards And Schematic Diagrams

    D-EJ855 5-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Waveforms 6 IC601 ik (RFDC) (CD play mode) 1 IC404 9 (CLK) Note on Printed Wiring Board Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF •...
  • Page 14: Printed Wiring Board

    D-EJ855 5-5. PRINTED WIRING BOARD • Semiconductor Location MAIN BOARD (COMPONENT SIDE) Ref. No. Location Ref. No. Location J301 LINE OUT IC405 J401 D303 H-13 (OPTICAL) TP418 EXT BATT D304 H-13 IC601 E-12 (GND) DC IN 4.5V D305 H-13 IC602 –...
  • Page 15: Schematic Diagram - Main Board (1/3)

    D-EJ855 5-6. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • • See page 13 for Waveforms. See page 18 for IC Block Diagrams. (Page 17) (Page 16) The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety.
  • Page 16: Schematic Diagram – Main Board (2/3)

    D-EJ855 5-7. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • See page 13 for Waveform. (Page 15) (Page 17)
  • Page 17: Schematic Diagram - Main Board (3/3)

    D-EJ855 5-8. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 13 for Waveforms. (Page 15) IC801 T5AJ4-3HE0 (Page 16)
  • Page 18: Ic Pin Function Description

    D-EJ855 5-9. IC PIN FUNCTION DESCRIPTION • IC Block Diagrams • IC403 TB2130F (FOCUS/TRACKING COIL DRIVER, SLED MOTOR DRIVER, POWER CONTROL) Pin No. Pin Name Description IC301 TA2152FN (EL) VREF Reference voltage input terminal RF41 Power supply 4 (APC) section operational amplifier 1 output...
  • Page 19 D-EJ855 Pin No. Pin Name Description INW1 Battery charge circuit error amplifier invert input for rechargeable battery Battery charge circuit error amplifier output for rechargeable battery VOUT1 VIN power supply circuit control transistor drive signal output terminal Not used (open)
  • Page 20 D-EJ855 • C601 CXD3029R (RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER) Pin No. Pin Name Description XRAS Row address strobe signal output to the D-RAM (IC602) Data input enable signal output to the D-RAM (IC602) 3 to 6...
  • Page 21 D-EJ855 Pin No. Pin Name Description VREFR R-ch reference voltage output terminal AOUT2 R-ch analog audio signal output AVDD2 — Power supply terminal (analog system) TES1 Input terminal for the test (normally: fixed at “L”) TEST Input terminal for the test (normally: fixed at “L”) VSS1 —...
  • Page 22 D-EJ855 Pin No. Pin Name Description SSTP Disc inner position detection signal input terminal Not used (fixed at “L”) Spindle motor (M902) drive signal output to the spindle motor driver (IC404) Spindle motor (M902) servo control signal output to the spindle motor driver (IC404) C176 176.4 kHz clock signal output to the power control (IC403) and spindle motor driver (IC404)
  • Page 23 D-EJ855 • IC801 T5AJ4-3HE0 (SYSTEM CONTROLLER) Pin No. Pin Name Description — Ground terminal (digital system) System clock input from the CXD3029R (IC601) XOUT High frequency oscillator output terminal Not used (open) TEST Test terminal for IC Not used (open) VCPU —...
  • Page 24 D-EJ855 Pin No. Pin Name Description 41 to 56 SEG15 to SEG0 Segment drive signal output terminal for the liquid crystal display Not used (open) 57 to 60 COM3 to COM0 Common drive signal output terminal for the liquid crystal display Not used (open)
  • Page 25: Exploded Views

    D-EJ855 Ver 1.1 SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark 0 are may have some difference from the original are seldom required for routine service.
  • Page 26: Cabinet (Lower) Section

    D-EJ855 Ver 1.1 6-2. CABINET (LOWER) SECTION EXCEPT FR CDM-3325ES Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3381-163-2 CABINET (LOWER) ASSY (NW) * 54 A-3021-686-A MAIN BOARD, COMPLETE (FR) (LIGHT GRAY BLUE)...(WHITE) (EXCEPT KR) 3-222-300-02 TERMINAL BOARD (+), BATTERY X-3381-164-2 CABINET (LOWER) ASSY (NG) 3-222-301-02 TERMINAL BOARD (–), BATTERY...
  • Page 27: Optical Pick-Up Section (Cdm-3325Es)

    D-EJ855 Ver 1.3 6-3. OPTICAL PICK-UP SECTION (CDM-3325ES) M902 M901 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce...
  • Page 28: Electrical Parts List

    D-EJ855 SECTION 7 ELECTRICAL PARTS LIST MAIN NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 29 D-EJ855 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C601 1-164-874-11 CERAMIC CHIP 100PF D601 8-719-083-04 DIODE RSB6.8STE61 C602 1-164-854-11 CERAMIC CHIP 15PF D801 8-719-074-30 LED CL-190UR-CD-T (CHARGE) C603 1-164-939-11 CERAMIC CHIP 0.0022uF 10% D803...
  • Page 30 D-EJ855 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L604 1-414-521-11 INDUCTOR 10uH R420 1-208-943-11 METAL CHIP 220K 0.5% 1/16W R421 1-208-927-11 METAL CHIP 0.5% 1/16W < TRANSISTOR > R422 1-208-927-11 METAL CHIP 0.5% 1/16W...
  • Page 31 D-EJ855 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R491 1-218-965-11 RES-CHIP 1/16W S805 1-771-248-11 SWITCH, TACTILE (x/CHARGE) R492 1-218-990-11 SHORT R601 1-218-969-11 RES-CHIP 1/16W S806 1-771-248-11 SWITCH, TACTILE (> N) R602 1-218-985-11 RES-CHIP...
  • Page 32 D-EJ855 Ver 1.1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-234-489-11 MANUAL, INSTRUCTION (SPANISH) (AEP, E33, JE) 3-234-489-21 MANUAL, INSTRUCTION (ENGLISH) (CND, AEP, UK, E33, AUS, JE) 3-234-489-31 MANUAL, INSTRUCTION (FRENCH) (CND, AEP, FR, JE)
  • Page 33 D-EJ855 US Model Canadian Model SERVICE MANUAL AEP Model UK Model E Model Ver 1.1 2002.01 Australian Model Chinese Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. Subject: Change of MAIN board. (Suffix-12) In this set, MAIN board has been changed in the midway of production.
  • Page 34 D-EJ855 • DIAGRAM NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
  • Page 35 D-EJ855 PRINTED WIRING BOARD • Semiconductor Location MAIN BOARD (COMPONENT SIDE) Ref. No. Location Ref. No. Location J301 LINE OUT IC405 J401 D303 H-13 (OPTICAL) TP418 EXT BATT D304 H-13 IC601 E-12 (GND) DC IN 4.5V D305 H-13 IC602 –...
  • Page 36 D-EJ855 SCHEMATIC DIAGRAM – MAIN Board (1/3) – ∗ R303, 304 220k (FR) 330k (EXCEPT FR) ∗ ∗ (Page 6) (Page 5) The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety.
  • Page 37 D-EJ855 SCHEMATIC DIAGRAM – MAIN Board (2/3) – (Page 4) (Page 6)
  • Page 38 D-EJ855 SCHEMATIC DIAGRAM – MAIN Board (3/3) – (Page 4) ∗ R821 22k 0.5% (EXCEPT FR) 68k 0.5% (FR) ∗ R822 100k 0.5% (FR) IC801 T5AJ4-3HE0 (Page 5)
  • Page 39 D-EJ855 MAIN • ELECTRICAL PARTS LIST NOTE: When indicating parts by reference • Due to standardization, replacements in the • Items marked “*” are not stocked since they number, please include the board. parts list may be different from the parts speci- are seldom required for routine service.
  • Page 40 D-EJ855 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D601 8-719-083-04 DIODE RSB6.8STE61 C602 1-164-854-11 CERAMIC CHIP 15PF D801 8-719-074-30 LED CL-190UR-CD-T (CHARGE) C603 1-164-939-11 CERAMIC CHIP 0.0022uF 10% D803 8-719-056-66 DIODE 1SS378-TE85L C604 1-164-938-11 CERAMIC CHIP 0.0015uF 10%...
  • Page 41 D-EJ855 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R416 1-216-298-00 METAL CHIP 1/10W < TRANSISTOR > R417 1-218-961-11 RES-CHIP 4.7K 1/16W Q301 8-729-028-86 TRANSISTOR DTA143EUA-T106 R418 1-218-973-11 RES-CHIP 1/16W Q302 8-729-429-50 TRANSISTOR XP4312 R419...
  • Page 42 D-EJ855 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R490 1-218-989-11 RES-CHIP 1/16W R822 1-208-935-11 METAL CHIP 100K 0.5% 1/16W R491 1-218-965-11 RES-CHIP 1/16W (French) R492 1-218-990-11 SHORT R493 1-218-969-11 RES-CHIP 1/16W < SWITCH >...
  • Page 43 D-EJ855 MEMO...
  • Page 44: Revision History

    D-EJ855 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.11...

Table of Contents