General; Getting Started - Sony SLV-D500P Service Manual

QQ
3 7 63 1515 0

1. GENERAL

Getting Started

Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR:
• Remote commander
• Size AA (R6) batteries
• 75-ohm coaxial cable with F-type connectors
• Audio/video cord
(pinplug ×3 y pinplug ×3)
TE
L 13942296513
8
Unpacking
Controlling other TVs with the remote commander
The remote commander is preprogramed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer's code number.
1
Set TV / DVD·VIDEO at the top of the remote commander to TV.
2 Hold down ?/1, and enter your TV's code number using the number buttons.
Then release ?/1.
Now you can use the ?/1, VOL +/–, CH +/–, MUTING*, TV/VIDEO and ENTER*
buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
* for Sony TV only
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
TV brand Code number
Sony 01
Akai 04
AOC 04
Centurion 12
Coronado 03
Curtis-Mathes 12
Daytron 12
Emerson 03, 04, 14
Fisher 11
General Electric 06, 10
Gold Star 03, 04, 17
Hitachi 02, 03
www
J.C.Penney 04, 12
JVC 09
KMC 03
Magnavox 03, 08, 12
.
Marantz 04, 13
MGA/Mitsubishi 04, 12, 13, 17
NEC 04, 12
10
Setting up the remote commander
http://www.xiaoyu163.com
TV brand Code number
Panasonic 06, 19
Philco 03, 04
Philips 08
Pioneer 16
Portland 03
Quasar 06, 18
Radio Shack 05, 14
RCA 04, 10
Sampo 12
Sanyo 11
Scott 12
Sears 07, 10, 11
Sharp 03, 05, 18
Sylvania 08, 12
x ao u163
y
Teknika 03, 08, 14
Toshiba 07
i
Wards 03, 04, 12
Yorx 12
Zenith 15
http://www.xiaoyu163.com
2 9
8
This section is extracted from instruction manual. (3-083-947-11)
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this DVD-
VCR and a Sony TV. Buttons on
the remote commander marked
with an orange dot (•) can be used
to operate your Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
To operate
the DVD player
the VCR
your TV
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Q Q
• Do not leave the remote commander in an extremely hot or humid place.
3 6 7 1 3 1 5
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
may cause a malfunction.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
co
.
1-1
9 4 2 8
Remote sensor
TV /
DVD·VIDEO
SELECT VIDEO
SELECT DVD
Set TV / DVD·VIDEO to
DVD·VIDEO, then press SELECT DVD and point at the remote sensor at
the DVD-VCR
DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor
at the DVD-VCR
TV and point at the remote sensor at your TV
0 5 8 2 9 9 4 2 8
Setting up the remote commander
m
Setting up the remote commander
SLV-D500P
9 9
9 9
continued
9
11