RX-5502(A) 2007.5.17 9:15 AM 페이지 2 SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should connection to grounding electrodes, and requirements for the be read before the product is operated. grounding electrode. See Figure 1. 2. Retain instructions - The safety and operating instructions should be retained for future reference.
RX-5502(A) 2007.5.17 9:15 AM 페이지 3 Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
RX-5502(A) 2007.5.17 9:15 AM 페이지 4 CONTENTS SAFETY INSTRUCTIONS ............................2 Introduction �READ THIS BEFORE OPERATING YOUR UNIT..................3 System Connections ............................5 Front Panel & Remote Controls ........................8 �REMOTE CONTROL OPERATION RANGE ....................10 �LOADING BATTERIES ..........................10 Operations �LISTENING TO A PROGRAM SOURCE ....................
RX-5502(A) 2007.5.17 9:15 AM 페이지 5 System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to connect the white RCA pin cords to the L (left) and the red RCA pin cords to the R (right) jacks when making audio connections.
RX-5502(A) 2007.5.17 9:15 AM 페이지 6 CONNECTING PHONO �Note •Do not connect the turntable with MC type cartridge directly. If so, use a separate head amplifier or step-up transformer. CONNECTING AUDIO COMPONENTS • The AUX jacks may also be connected to an additional component.
RX-5502(A) 2007.5.17 9:15 AM 페이지 7 CONNECTING SPEAKERS • You can connect up to four pairs of speakers to this receiver and select the various combinations of speakers according to your tastes. • The speakers C and D can be installed in...
RX-5502(A) 2007.5.17 9:15 AM 페이지 8 Front Panel & Remote Controls �FRONT PANEL �FLUORESCENT DISPLAY �REMOTE CONTROLS...
Page 10
RX-5502(A) 2007.5.17 9:15 AM 페이지 9 1. POWER SWITCH 13. BALANCE BUTTON Push this switch to enter the standby mode. When adjusting the sound volume balance, press To switch the power off, push again this switch. this button to enter the balance mode.
RX-5502(A) 2007.5.17 9:15 AM 페이지 10 REMOTE CONTROL OPERATION RANGE �Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES Remove the cover.
RX-5502(A) 2007.5.17 9:15 AM 페이지 11 Operations LISTENING TO A PROGRAM SOURCE Before operation ∙Push the POWER switch. • This unit enters the standby mode and the STANDBY indicator lights up. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness.
Page 13
RX-5502(A) 2007.5.17 9:15 AM 페이지 12 Select the desired input source. �Each time the "INPUT SELECT ◀/▶" buttons are pressed, the input source is changed as follows : →TUNER ↔ CD ↔ AUX ↔ DVD ↔ TAPE ↔ PHONO ←...
Page 14
RX-5502(A) 2007.5.17 9:15 AM 페이지 13 To listen with the headphones. • Be sure to switch off all the speakers installed in the main room. Adjusting the tone (bass and treble) Enter the tone mode. • Each time this button is pressed, the corresponding...
Page 15
RX-5502(A) 2007.5.17 9:15 AM 페이지 14 Adjusting the sound volume balance Enter the balance mode. • "BAL" and the balance level are displayed for 5 seconds. Adjust the sound volume balance between the left and right speakers. • If the balance display disappears, start from the step 11 again.
RX-5502(A) 2007.5.17 9:15 AM 페이지 15 LISTENING TO RADIO BROADCASTS Auto tuning Select the tuner and then the desired band. • Each time this button is pressed, the tuner is automatically selected and the band is changed as follows : →...
Page 17
RX-5502(A) 2007.5.17 9:15 AM 페이지 16 Manual tuning • Manual tuning is useful when you already know the frequency of the desired station. • Perform the steps 1 and 2 in "Auto tuning" procedure on page 15 and press the TUNING/PRESET UP (▲...
Page 18
RX-5502(A) 2007.5.17 9:15 AM 페이지 17 Press the TUNING/PRESET UP ( or DOWN ( ) button to select the desired preset ▲/+) ▼/- number and press the MEMORY button. • The station has now been stored in the memory. • A stored frequency is erased from the memory by storing another frequency in its place.
RX-5502(A) 2007.5.17 9:15 AM 페이지 18 RECORDING • The volume, tone(bass, treble) and balance settings have no effect on the recording signals. • When you select tuner, CD, DVD, AUX or PHONO as a recording source, recording can be made on the TAPE.
RX-5502(A) 2007.5.17 9:15 AM 페이지 19 ROOM2 PLAYBACK • This function allows enjoying one source in the main room and playing another in a different room at the same time. • Even when this receiver enters the standby mode, in such a case that "R2" is dimly lit, meaning only the ROOM2 circuitry operates, the ROOM2 source can be played independently.
Page 21
RX-5502(A) 2007.5.17 9:15 AM 페이지 20 Select the desired ROOM2 input. • Each time the "INPUT SELECT ◀/▶" buttons are pressed, the ROOM2 input source is changed as follows : →TUNER ↔ CD ↔ AUX ↔ DVD ↔ TAPE ↔ PHONO ←...
RX-5502(A) 2007.5.17 9:15 AM 페이지 21 Troubleshooting Guide If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult with your dealer.
RX-5502(A) 2007.5.17 9:15 AM 페이지 22 Specifications � AMPLIFIER SECTION • Power output, 8Ω, THD 0.7 %, 20 Hz~20 kHz, only a pair of speakers driven ........2 X 100 W • Total harmonic distortion, 8Ω, @ -3dB, 20 Hz~20 kHz ................0.05 % •...