Introduction READ THIS BEFORE OPERATING YOUR UNIT : TO REDUCE THE RISK OF ELECTRIC CAUTION SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, WARNING DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.
CONTENTS Introduction READ THIS BEFORE OPERATING YOUR UNIT... 2 SAFETY INSTRUCTIONS ... 3 System Connections ... 5 Front Panel & Remote Controls ... 7 REMOTE CONTROL OPERATION RANGE ... 9 LOADING BATTERIES ... 9 Operations LISTENING TO A PROGRAM SOURCE ... 10 LISTENING TO RADIO BROADCASTS ...
System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to connect the white RCA pin cords to the L(left) and the red RCA pin cords to the R(right) jacks when making audio connections.
REMOTE SENSOR SLEEP • You can remotely control not only this receiver but also Sherwood compatible components bearing the DIGI LINK II or III logo. • For system remote control operation, first make the DIGI LINK connections. • In the DIGI LINK III remote control system, if pressing PLAY, etc.
Page 8
POWER BUTTON In the standby mode, press this button, then this unit is turned on to enter the operating mode. STANDBY BUTTON In the operating mode, press this button or the POWER button on the front panel, then this unit is turned off to enter the standby mode.
TAPE DECK SECTION DECK SELECTOR A, B- for selecting deck A or B - to begin reverse or forward side playback. - to wind up the tape reversely or forwardly. - for recording. - to stop playback or recording. FLUORESCENT DISPLAY INPUT, FREQUENCY, VOLUME LEVEL, OPERATING INFORMATION, etc.
Operations LISTENING TO A PROGRAM SOURCE Turn the power on. STANDBY POWER ON POWER ON POWER ON ON/STANDBY DECK SEL. DECK SEL. TREBLE FM MODE Switch the desired speakers on. POWER ON POWER ON SPEAKER SPEAKER SPEAKER SPEAKER SPEAKER Then the corresponding speaker indication(“SPK DECK SEL.
Page 11
POWER ON STANDBY SLEEP SPEAKER DIMMER VIDEO TAPE TV/AUX REPEAT TUNER To mute the sound. INTRO DECK SEL. TREBLE TREBLE BASS BASS MUTE MUTE MUTE VOL. VOL. TUNE TUNE TUNE TUNE MEMO MEMO FM MODE FM MODE P.SCAN P.SCAN VOL. VOL.
LISTENING TO RADIO BROADCASTS Auto tuning Select the tuner and then the desired band. POWER ON STANDBY ANDBY DIMMER DIMMER SLEEP SLEEP SPEAKER SPEAKER FM/AM TAPE PHONO PHONO REPEA REPEAT TUNER TUNER INTRO INTRO DECK SEL. DECK SEL. TAPE POWER ON TREBLE BASS SPEAKER...
Page 13
Select the desired preset number (1~30) and press the MEMORY button. TUNE TUNE TUNE TUNE MEMORY TREBLE TREBLE BASS BASS MUTE MUTE VOL. VOL. TUNE TUNE TUNE TUNE MEMO MEMO FM MODE FM MODE P.SCAN P.SCAN VOL. VOL. • When using the NUMERIC buttons on the remote control.
VOL. FM MODE P .SCAN VOL. When the sleep time is selected, all display panels of Sherwood components connected by the DIGI LINK III are dimly lit. REMOTE CONTROL RM-110 REMOTE CONTROL RM-117 Recording with AUX Select the desired input as a recording source except for AUX.
Remote control unit does • Batteries are not loaded or exhausted. not operate. • The remote sensor is obstructed. Other Sherwood components • DIGI LINK connections are not made do not react to remote control properly. commands.