Advertisement
Quick Links
Model 027125-07012
HAND TORQUE WRENCH
Installation and Operating Manual
For assistance with the operation of this product,
contact PCB Piezotronics, Inc.
Toll-free: 800-828-8840
24-hour SensorLine: 716-684-0001
Fax: 716-684-0987
E-mail: info@pcb.com
Web: www.pcb.com
Advertisement
Related Manuals for PCB Piezotronics 027125-07012
Summary of Contents for PCB Piezotronics 027125-07012
- Page 1 Model 027125-07012 HAND TORQUE WRENCH Installation and Operating Manual For assistance with the operation of this product, contact PCB Piezotronics, Inc. Toll-free: 800-828-8840 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com Web: www.pcb.com...
- Page 2 Returning Equipment – Following the equipment to PCB Piezotronics for these procedures will insure that your repair. User servicing or repair is not returned materials are handled in the recommended and, if attempted, may most expedient manner.
- Page 3 PCB Piezotronics, Inc. Warranty – All equipment and repair 3425 Walden Ave. services provided by PCB Piezotronics, Depew, NY 14043 USA Inc. are covered by a limited warranty Toll-free: (800) 828-8840 against defective...
- Page 4 Hand Torque-Angle Wrench Installation and Operating Manual For assistance with the operation of this product, contact: RS Technologies Division of PCB Load & Torque, Inc. Toll-Free in USA: 888-684-2894 24-hour SensorLine : 716-684-0001 Fax: 248-888-8266 E-mail: rsinfo@pcbloadtorque.com 9/30/2011...
- Page 5 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Introduction: Safety Considerations The Model 962 should not be opened by anyone other than factory personnel. There are no user AUTION serviceable parts inside of the Model 962 recorder. Cables can kill your equipment. High voltage electrostatic discharge can damage electrical devices. AUTION Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the following:...
- Page 6 Figure 1–Hand Torque Wrench Wheatstone Bridge Part No. Drive Size Handle Capacity With Angle Wiring Code 027125-07012 ¼-inch 8-in. 100 lb-in The gages are bonded to the wrench’s flexure. Typically, a (11.4 Nm) regulated DC or AC excitation is applied between A and B of...
- Page 7 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL 2.0 SAFETY INFORMATION 6.0 SHUNT CALIBRATION Applied loads must be limited to 100% of the rated capacity. Shunt calibration is the known, electrical unbalancing of a Application of loads exceeding rated capacity can lead to strain gage bridge by means of a fixed resistor that is placed, damage of the hand torque wrench and potential injury to the or “shunted”, across one leg of the bridge.
- Page 8 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL During use, a GREEN gyro status light indicates gyro 6.2 Basic Shunt Calibration Procedure operation is normal. The following procedure outlines the basic routine of shunt calibration. The actual calibration procedure performed by If the status light flashes RED, angular velocity has exceeded your data collector may be automated and will differ.
-
Page 9: Troubleshooting
HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Figure 3—Hold the handle of wrench perpendicular to the centerline Figure 6—Do not jerk the handle abruptly or you may get or shank of the fastener. inaccurate and inconsistent readings. 8.0 TROUBLESHOOTING When having difficulty operating the hand torque wrench, refer to the following checklist. -
Page 10: Maintenance
HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Zero Drift 9.0 MAINTENANCE Unconditioned power supply Open circuit or short The hand torque wrenches provided by RS Technologies Loose wiring Division of PCB Load & Torque Inc. are made of durable RFI/EMI interface materials, and are intended for industrial use. However, routine Temperature change maintenance, such as cleaning of electrical connectors, Wrench moved on power ON before... - Page 11 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL MANUAL NUMBER: 51051 MANUAL REVISION: A ECN NUMBER: 37134 RS Technologies Division of PCB Load & Torque, Inc. Toll-Free in USA 888-684-2894 716-684-0001 www.pcbloadtorque.com...
- Page 12 Model Number Revision: C HAND TORQUE WRENCH 027125-07012 ECN #: 38924 Performance ENGLISH OPTIONAL VERSIONS Measurement Range(Full Scale Capacity) 100 in-lb 11.4 Nm Optional versions have identical specifications and accessories as listed for the standard model except where noted below. More than one option may be used.
- Page 13 (716) 684-0001 E-MAIL: ltinfo@pcbloadtorque.com OUTLINE DRAWING ANGLES .5 DEGREES ANGLES .5 DEGREES DWG. NO. 027125-07012 49862 1.) FINISH: BLACK HARD COAT ANODIZE. 1/4" SQ. DRV. 100 lb-in [11.4 Nm] FILLETS AND RADII FILLETS AND RADII .015 MAX 0.38 MAX SCALE:...
Need help?
Do you have a question about the 027125-07012 and is the answer not in the manual?
Questions and answers