Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PCB Piezotronics IMI SENSORS 080A134
Summary of Contents for PCB Piezotronics IMI SENSORS 080A134
- Page 1 Model 080A134 Spotface tool, 2.25" dia., 1/4-28 tapped hole Installation and Operating Manual For assistance with the operation of this product, contact the PCB Piezotronics, Inc. Toll-free: 800-959-4464 24-hour SensorLine: 716-684-0001 Fax: 716-684-3823 E-mail: imi@pcb.com Web: www.imi-sensors.com...
- Page 2 Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T.
- Page 3 CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
- Page 4 PCB工业监视和测量设备 - 中国RoHS2公布表 PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table 有害物质 镉 汞 铅 (Pb) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 部件名称 (Hg) (Cd) 住房 PCB板 电气连接器 压电晶体 环氧 铁氟龙 电子 厚膜基板 电线 电缆 塑料 焊接...
- Page 5 Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
- Page 6 INDUSTRIAL MONITORING INSTRUMENTATION DIVISION Spot Face Tool User Instructions Operating Guide with Enclosed Warranty Information 3425 Walden Avenue, Depew, New York 14043-2495 Phone (716) 684-0003 Fax (716) 684-3823 Toll Free Line 1-800-959-4IMI MANUAL NUMBER: 18671 MANUAL REVISION: A...
-
Page 7: Table Of Contents
INDUSTRIAL MONITORING INSTRUMENTATION DIVISION table of contents Introduction ........................page 3 Installation ........................page 3 Operation ........................pages 3-4 Tool Maintenance ......................page 4 Spot Face Tool Illustration ....................page 5 return procedure/customer service Return Procedure ......................page 6 Customer Service ......................page 6 PAGE 2... -
Page 8: Introduction
INDUSTRIAL MONITORING INSTRUMENTATION DIVISION introduction Spot face tools are used to create a flat circular surface to mount an accelerometer. Each model has an installed center drill that is the correct tap drill for tapping a ¼-28 UNF-2B thread. installation Obtain a hand drill motor and install the shank end of the spot face tool into the chuck of the drill motor. -
Page 9: Tool Maintenance
INDUSTRIAL MONITORING INSTRUMENTATION DIVISION operation continued . . . The depth of the cut is determined by the perpendicularity of the surface to the axis being measured. Remove enough material so that the entire bottom surface of the accelerometer is in contact with the spot face. -
Page 10: Spot Face Tool Illustration
INDUSTRIAL MONITORING INSTRUMENTATION DIVISION PAGE 5... -
Page 11: Return Procedure
IMI, a division of PCB Piezotronics, guarantees Total Customer Satisfaction. If, at any time, for any reason, you are not completely satisfied with any IMI product, IMI will repair, replace, or exchange it at no charge. You may also choose, within the warranty period, to have your purchase price refunded.
Need help?
Do you have a question about the IMI SENSORS 080A134 and is the answer not in the manual?
Questions and answers