Beko DCU8230 Service Manual
  1. Manuals
  2. Brands
  3. Beko Manuals
  4. Dryer
  5. DCU 8230
  6. Service manual

Beko DCU8230 Service Manual

2010 led 8kg
Hide thumbs Also See for DCU8230:
Table of Contents

Advertisement

Quick Links

See also: Installation & Operating Instructions and Drying Guidance , User Manual
Beko 2010 LED 8 kg Condanser
Tumble Dryer Service Handbook
1.
2.
3.
4.
5.
Fault algorithms
6.
7.
Exploded views
8.
9.
Demounting the dryer

INDEX

1

Advertisement

Table of Contents
loading

Related Manuals for Beko DCU8230

Summary of Contents for Beko DCU8230

  • Page 1 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook INDEX Technical Specifications Components and Dryer Principals Control System Service test program Fault algorithms Wiring schematics Exploded views Spare part list Demounting the dryer...
  • Page 2 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook...

  • Page 3: Technical Specifications

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Technical Specification: 1.1. Product Definition 1.1.1. Manufacturer : Arçelik A.Ş. Cerkezkoy - Tekirdag / TÜRKĐYE 1.1.2 Model : BEKO DCU8230 1.1.3 Capacity (kg) 1.1.4 Programs (Qty) : 10 sensor controlled program...
  • Page 4 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 1.7. Power Cord 1.7.1. Type : 3 x 1.5 mm2 Cord Copper wire 1.7.2. Insulation : TS 9760 H05V2V2-F 3G1,5mm 1.7.3. Plug : Earthed ,PVC injected 1.7.4. Length (mm) : 1605 1.8.
  • Page 5 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook With the multimeter manual resetting thermostat is checked from the terminals while heater is on the dryer. If manual resetting thermostat is open curcuit, the button is up and the heater does not work.
  • Page 6 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 1.9.5. NTC (regulating thermistor) : 19.500 ohm @ 25° C Type : ELTH 279 1.10. Door NTC Door NTC (ohm) : 12.000 ohm @ 25° C 1.11. Body : 1.11.1.

  • Page 7: Components And Dryer Principals

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 2. Components and Dryer Principals: Electronic Board: Humidity Sensor Connector Door Sensing Programming 700W Motor Direction 1 Connector Drain Pump Motor Direction 2 Relay Transformer Heater and Door NTC 3-6-9 Delay...
  • Page 8 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Heater (Open spiral wire): A 2300W two circuit open spiral wire type heater is driven by the 2 relays. A manual resettable thermostat is used on these heater, in order to provide IEC safety rules accordingly. This manual resettable thermostat cut the heater power at 160°...
  • Page 9 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Motor: Tumble and fan turns via 2 poles asenkron motor. Motor turns 2750 prm ans has a 9 uF capacitor. Asenkron motor is controled by two Control panel two relays one of them for direction, other one is for energy that placed in control.
  • Page 10 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Dryer Principals: The air heated by the heaters, is directed to the drum and gets moisture of the laundry. After crossing from the filters, the air pass through the condenser, and condenses.

  • Page 11: Control System

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 3. Control System:...
  • Page 12 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook...
  • Page 13 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook...
  • Page 14 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook...
  • Page 15 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook...

  • Page 16: Service Test Program

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 4. Service Test Program: Step 1: Program selector is set as delicates and while pressing the buzzer cancel button, turn on dryer. After 3 seconds service test program starts and buzzer sounds. In this program start/pause/cancel button is used to pass other steps.
  • Page 17 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Step 7: The start/stop/cancel button is pushed. The drying led goes off and the ready to iron led is activated. Motor turns clockwise. The 1600W heater is on. After 3 seconds buzzer/cancel led blinks.

  • Page 18: Fault Algorithms

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 5. Faults Algorithms : No Power Supply Check the electrical Connect the power supply connections Check the Change the main card electricity on the main control card Check the on/off...
  • Page 19 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Degree of drying can’t be reached or drying time is too long Check the Check the software,change heaters relays the main card Is the heater Reset the heater thermic (NC)
  • Page 20 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Program can not be set Are the values on the program selector Each turn of rotary knob,there potentiometer should be 1Kohm increase. If it is correct not, change the rotary...
  • Page 21 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook The drum is not rotating Fix the V-belt? Is V-belt on? Are the motor Check the software,change relays running? the main control card Are motor winding Motor heating problem,wait resistance are...
  • Page 22 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Program doesn’t progress although the tank is empty. Is the overflow switch is Fix or change the overflow switch broken? Is the overflow switch is broken? Fix or change the overflow...

  • Page 23: Wiring Schematics

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 6. Wiring Schematics: Beko 2010 Condenser LED Wiring Schematics...
  • Page 24 Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook Beko 2010 Condenser Cable Schematics...

  • Page 25: Spare Part List

    Beko 2010 LED 8 kg Condanser Tumble Dryer Service Handbook 7. Expoled Views: 8. Spare Parts List: 9. Demounting:...

Table of Contents