Advertisement
Installations
(continued)
3. Install the inner cover.
Slide the covers located on the both lateral
sides of the camera and put the inner cover on
the camera until the hooks inside the inner cover
are held in the holes of the camera (until a click
is heard).
Important: Put the inner cover down on the
camera until the outside cover of the camera
cannot be seen from the opening (from
which the camera lens is visible) of the inner
cover. If this integration is not successfully
performed, the inner cover may be removed
or the hidden part at the top of the screen
may become larger in the WIDE mode.
How to remove the inner cover
Press the inner cover from the front and rear
sides inward (at the same vertical position as
the hooks) to bend the cover and remove the
shell from the camera.
4. Mount the top cover on the wall and run the cables.
Secure the top cover in either of the following
two ways: q and w. No screw is supplied.
Procure screws according to the installation
area.
q M4 screws, 4 positions (a)
or
w M4 screws, 2 positions ((a) upper 2 posi-
tions, not available in lower positions) and
M6 or M8 anchor bolts, 2 positions (b)
Important: The length of the anchor bolt pro-
jecting portion (the distance between the tip
of the anchor bolt and the chassis attaching
surface) shall be 7 mm {1/4"} or less. Failure
to observe this causes interference between
the anchor bolt and bottom cover. Therefore,
the bottom cover cannot be mounted.
5. Mount the camera.
Refer to the Installation Guide of network cam-
era for further information.
The camera mounting bracket is already
attached to this bracket at the time of purchase.
Make sure to use the provided mount bracket.
Important: When mounting the camera, push
the camera securely into the mounting sec-
tion of the top cover.
6. Mount the bottom cover.
Be sure to push the bottom cover up until a click is heard.
Important: Do not let the cables be caught dur-
ing installation work.
7. Tighten the fixing screw to be used for cover fall prevention.
Recommended tightening torque: 1.6 N·m {16 kgf·cm}
Inner cover
Cover
Hook
Put on until a click is heard
Press from the front and rear
sides inward to bend
(a)
(a)
(b)
(a)
(a)
(b)
7 mm {1/4"}
Anchor bolt
Safety wire
Camera fixing screw
(accessory of the network camera)
Bottom cover
Note: When the camera is pointed in the horizontal direction, the upper side of the screen is
hidden. Refer to the Operating Instructions (PDF) of network camera for further information.
Specifications
Ambient temperature:
–10 °C to +50 °C {14 °F to 122 °F}
Dimensions:
165 (W) x 206.5 (H) x 217.5 (D) mm
{6-1/2 inches (W) x 8-1/3 inches (H) x 8-9/16 inches (D)}
Mass:
Approx. 950 g {2.10 lbs}
Finish:
Main body: Treatment steel
Top and bottom covers: ABS resin with silver metallic coating
Dome cover: Acrylic resin
Standard Accessories
Operating Instructions (this book) ............................. 1 pc.
The following are for installation.
Template .................................................................... 1 sheet
Inner cover ................................................................ 1 pc.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2012
For Europe and other countries:
http://panasonic.net
Importer's name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg F.R.Germany
Advertisement
