Aquatic AQ-MP-5BT-H User And Installation Manual
  1. Manuals
  2. Brands
  3. Aquatic Manuals
  4. Car Receiver
  5. AQ-MP-5BT-H
  6. User and installation manual

Aquatic AQ-MP-5BT-H User And Installation Manual

Waterproof media player for bluetooth & mp3 devices
Hide thumbs Also See for AQ-MP-5BT-H:
Table of Contents

Advertisement

Quick Links

®
products with a watertight reputation
AQ-MP-5BT-H - WATERPROOF MEDIA PLAYER
for Bluetooth & MP3 devices
USER / INSTALLATION MANUAL
Replaces Factory Radio on Harley-Davidson
Motorcycles
®
(Models 1996-2013)
USB
charging
PLEASE READ THIS INSTRUCTION MANUAL BEFORE
INSTALLATION AND OPERATION

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AQ-MP-5BT-H and is the answer not in the manual?

Questions and answers

Randy Dixon
May 14, 2025

My radio keeps changing station like it's always in seek mode. How can I get it to stay on 1 station

0
1 comments:
Mr. Anderson
May 21, 2025

To stop the Aquatic AQ-MP-5BT-H radio from changing stations automatically, avoid using the AS/PS (Auto Scan/Preset Scan) function. This feature scans the current frequency band and assigns presets to stations with the strongest signals, which may cause automatic station changes.

Also, ensure the radio is not in manual seek mode, which is activated by a long press on the Fast Forward or Rewind buttons. Manual seek mode may cause the radio to change stations when scanning.

Use short presses on the tuning buttons or manually select presets using the 'Preset' button to control station selection.

This answer is automatically generated

0
Tim Bryson
March 11, 2025

Where is the setting to turn on the rear speakers

0
1 comments:
Mr. Anderson
March 11, 2025

To turn on the rear speakers for the Aquatic AQ-MP-5BT-H, follow these steps:

1. Ensure the rear speaker wires are properly connected. Cut the rear channel speaker wires from the 35-pin harness at:
- Pins 1 and 24 for the right side.
- Pins 2 and 25 for the left side.
2. Strip the wires and connect them using crimp caps or solder, then cover with a non-conductive heat shrink tube.
3. After installation, test the rear speakers for sound.
4. If there is no sound, check the settings menu and ensure the rear speakers are set to "ON."

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Aquatic AQ-MP-5BT-H

Summary of Contents for Aquatic AQ-MP-5BT-H

  • Page 1 ® products with a watertight reputation AQ-MP-5BT-H - WATERPROOF MEDIA PLAYER for Bluetooth & MP3 devices USER / INSTALLATION MANUAL Replaces Factory Radio on Harley-Davidson Motorcycles ® (Models 1996-2013) charging PLEASE READ THIS INSTRUCTION MANUAL BEFORE INSTALLATION AND OPERATION...

  • Page 2: Table Of Contents

    Table of Contents Media Player AQ-MP-5BT-H 1 Getting Started......................... 1.1 Contents..........................1.2 Connections........................1.3 Wiring Diagram........................1.4 Mounting Precautions......................1.5 Installing the Media Player if no stereo is already installed..........1.6 Installing the Media Player if an existing factory stereo is already installed......

  • Page 3: Getting Started

    Getting Started Media Player AQ-MP-5BT-H 1.1 Contents • AQ-MP-5BT-H Digital Media Player • Four-pin Speaker Wiring Harness • Owner’s Manual 1.2 Connections (see also ‘1.3 Wiring Diagram’) 1. 23-pin Harley-Davidson Standard Harness Connection ® The 23-pin harness supplies power and ground connections to the Media Player and two speaker channel output connections from the Media Player.

  • Page 4: Wiring Diagram

    Getting Started Media Player AQ-MP-5BT-H 1.3 Wiring Diagram No lower than a 2 Ohm load should be used or damage may occur to the Media Player. Make sure the polarity of speakers are connected correctly. www.aquaticav.com...

  • Page 5: Mounting Precautions

    Getting Started Media Player AQ-MP-5BT-H 1.4. Mounting Precautions Please observe the following precautions: 1. Install the unit where it does not interfere with driving. 2. Check clearances on both sides of a planned installation before drilling any holes or installing any screws.

  • Page 6: Installing The Media Player If An Existing Factory Stereo Is Already Installed

    Media Player. 1. Unplug the 23-pin harness and FM/AM radio antenna from the factory stereo. 2. Remove the factory stereo and replace with the AQ-MP-5BT-H Media Player using the existing factory mounting hardware.

  • Page 7: Handle Bar Controls

    Accesses Audio menu adjustments 1.8 Power On The AQ-MP-5BT-H requires +12V DC to both the red and yellow wires. When both of these wires have power the AQ-MP-5BT-H is powered on. Ground is connected to the black wire. Once all connections are made press the rotary knob and the stereo will turn ON.

  • Page 8: Location Of Controls

    Location of Controls Media Player AQ-MP-5BT-H 2.1 Media Player Controls 1. Front face release 4. Mode button 7. Audio/System menu 10. ESC/Info 2. Preset station 5. Band button 8. XBS function 11. DSP/Dimmer 3. Fast Rewind/Forward 6. LCD screen 9. Play/Pause 12.

  • Page 9: Listening To Devices

    3.1.1 Pair with Bluetooth Device 1. Switch on your Bluetooth device. 2. Select ‘AQUATIC AV’ from the list of available devices to pair (no password is needed). 3. A Bluetooth logo will illumiate on the Media Player LCD to verify Bluetooth is activated.

  • Page 10: Listening To Fm/Am Radio

    Listening to FM/AM Radio Media Player AQ-MP-5BT-H 4.1 Enter FM/AM Radio Mode 1. Press MODE on the unit keypad to switch to FM/AM radio mode. 4.2 Scan or Navigate FM/AM Radio Channels 1. Press FAST REWIND/FAST FORWARD to seek another station.

  • Page 11: Settings Menu

    Settings Operation Media Player AQ-MP-5BT-H 5.1 Audio Menu From the ‘Audio Menu’ you are able to change the bass, treble, balance, and fader. 1. To enter the ‘Audio Menu’ press the ‘AUDIO/MENU’ button. 2. In the ‘Audio Menu’ press the ‘AUDIO/MENU’ button to scroll through all options.

  • Page 12: Specifications & Dimensions

    Specifications & Dimensions Media Player AQ-MP-5BT-H 6.1 Specifications Media Supported media........Bluetooth/MP3/FM/AM Supported media max. dimensions... 107 x 184mm (WxH) Device charging........via USB Inputs Auxiliary..........1x 3.5mm stereo Jack socket, 1x stereo pair RCA Outputs Pre-Out..........1x stereo pair RCA (2V) Power Output voltage @ 2 Ohm......

  • Page 13: Warranty Information

    Some states do not allow limitations on the length of an implied warranty, so this limitation may not apply. No person is authorized to assume for Aquatic AV any other liability in connection with the sale of the product. How to obtain service You must obtain a return material authorization number (RMA) to return any product to Aquatic AV.
  • Page 14 FCC Statement Media Player AQ-MP-5BT-H FCC ID: MADE IN CHINA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 15 Aquatic AV 282 Kinney Drive San Jose, CA 95112, USA E-mail: info@aquaticav.com US & Canada: 1 877 579 2782 ® International: +1 408 559 1668 Fax: +1 408 559 0125 www.aquaticav.com products with a watertight reputation...

Table of Contents

Save PDF