IBM 6558-03N Service Manual page 11

Customizing Your Monitor
Using the OPTION On-screen
Display
The OPTION OSD allows you to manually degauss the
screen and adjust settings such as the OSD position and
power saving delay time. It also allows you to lock the
controls.
Degaussing the screen
The monitor screen is automatically degaussed
(demagnetized) when the power is turned on.
You can also manually degauss the monitor.
1
Press the button.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select "
OPTION," and press the button again.
The OPTION OSD appears.
OPTION
ON
ZZ...
1 MIN
UNLOCK
MANUAL DEGAUSS
3
Press the ¨./> buttons to select " (MANUAL
DEGAUSS)."
4
Press the > / button.
The screen is degaussed for about 3 seconds.
If you need to degauss the screen a second time, wait for at
least 20 minutes before repeating the steps above.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the button again.
12
Changing the on-screen display position
You can change the OSD position (for example, when you
want to adjust the picture behind the OSD).
1
Press the button.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select "
OPTION," and press the button again.
The OPTION OSD appears.
OPTION
ON
ZZ...
1 MIN
UNLOCK
MANUAL DEGAUSS
3
Press the ¨./> buttons to select " (OSD H
POSITION)" or " (OSD V POSITION)."
Select " (OSD H POSITION)" to adjust the horizontal
position.
OPTION
ZZ... 1 MIN
UNLOCK
OSD H POSITION
Select " (OSD V POSITION)" to adjust the vertical
position.
OPTION
1
ZZ...
UNLOCK
OSD V POSITION
4
Press the >?// buttons to move the OSD to the
desired position.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the button again.
To reset, press the ? (reset) button while the OSD is on.
Setting the power saving delay time
You can set the delay time before the monitor enters the
power saving mode. See page 15 for more information on
this monitor's power saving capabilities.
1
Press the button.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select "
OPTION," and press the button again.
The OPTION OSD appears.
OPTION
ON
ZZ... 1 MIN
UNLOCK
MANUAL DEGAUSS
3
Press the ¨./> buttons to select " ZZ... (PWR SAVE
DELAY)."
OPTION
1
5 SEC 1 MIN
ZZ...
60 MIN OFF
PWR SAVE DELAY
4
Press the >?// buttons to select the desired time.
When PWR SAVE DELAY is set to "OFF," the monitor
does not go into power saving mode.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the button again.
To reset, press the ? (reset) button while the OSD is on.
Getting Started
Customizing Your Monitor
Locking the controls
The control lock function disables all of the buttons on the
front panel except the u (power) switch and button.
1
Press the button.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select "
OPTION," and press the button again.
The OPTION OSD appears.
OPTION
ON
ZZ...
1 MIN
UNLOCK
MANUAL DEGAUSS
3
Press the ¨./> buttons to select " (CONTROL
LOCK)."
OPTION
1
ZZ...
UNLOCK LOCK
CONTROL LOCK
4
Press the >?// buttons to select "LOCK."
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the button again.
Once you select "LOCK," you cannot select any items
except "EXIT" and " OPTION" in the MENU OSD.
If you press any button other than the u (power) switch and
button, the mark appears on the screen.
To cancel the control lock
Repeat steps 1 through 3 above and press the >?//
buttons to select "UNLOCK."
EN
F
ES
C
13