6557-03N/03S/43N/43S SERVICE MANUAL 6557-03N/43N N. Hemisphere Model AEP Model Japan Model 6557-03S/43S S. Hemisphere Model CHASSIS SPECIFICATIONS Picture tube 0.25 – 0.27 mm aperture grille pitch Deflection frequency Horizontal: 30 to 94 kHz 19 inches measured diagonally Vertical: 50 to 160 Hz 90-degree deflection 256 Total Line 2048...
Page 2
6557-03N/03S/43N/43S SAFETY CHECK-OUT (US Model only) After correcting the original service problem, perform the fol- 3. Measuring the voltage drop across a resistor by means of a lowing safety checks before releasing the set to the customer: VOM or battery-operated AC voltmeter. The “limit” indica- 1.
Page 3
6557-03N/03S/43N/43S POWER SAVING FUNCTION This monitor meets the power-saving guidelines set by Note VESA and Energy Star, as well as the more stringent If no video signal is input to the monitor, the “NO INPUT SIGNAL” message (page 18) appears. After the delay time has NUTEK .
Page 4
6557-03N/03S/43N/43S TIMING SPECIFICATION MODE AT MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 MODE 9 PRODUCTION RESOLUTION 656 X 496 640 X 480 800 X 600 1024 X 768 1024 X 768 1280 X 1024 1280 X 960 1280 X 1024 1600 X 1200...
6557-03N/03S/43N/43S TABLE OF CONTENTS Section Title Page 1. GENERAL ..............1-1 2. DISASSEMBLY 2-1. Cabinet Removal ..........2-1 2-2. A Board Removal ..........2-1 2-3. AC inI/O TERMINAL Board Removal ..... 2-2 2-4. D Board Removal ..........2-2 2-5. Service Position ..........2-3 2-6.
SECTION 1 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of GENERAL the Operating Instruction Manual remain as in the manual. Getting Started Getting started Getting Started Getting Started Warning on power connection Precautions Identifying Parts and Controls •...
Page 7
Getting Started Getting Started Getting Started 9 Video input 2 connector (13W3 cable) Setup Automatically Adjusting the Size Selecting the Input Signal Inputs RGB video signal (0.700 Vp-p, positive). and Centering of the Picture This monitor works with platforms running at horizontal This monitor has two signal input connectors (HD15 and frequencies between 30 and 94 kHz.
Page 8
Getting Started Customizing Your Monitor Getting Started Customizing Your Monitor Press the >?// buttons to select “1” or “2.” Before adjusting Introducing the On-screen Using the CENTER On-screen • Connect the monitor and the computer, and turn them on. • Select “ LANG”...
Page 9
Customizing Your Monitor Getting Started Customizing Your Monitor Press the >?// buttons to adjust the settings. Using the SIZE On-screen Display Using the GEOM (Geometry) On- Using the ZOOM On-screen screen Display Display The SIZE settings allow you to adjust the size of the picture. Once the setting is adjusted, it will be stored in memory for The GEOM (geometry) settings allow you to adjust the The ZOOM settings allow you to enlarge or reduce the...
Page 10
Customizing Your Monitor Getting Started Customizing Your Monitor Select Press Using the COLOR On-screen Display Using the SCREEN On-screen / . . . to shift red shadows up and blue turn the moire cancellation function Display shadows down “ON” or “OFF.” CANCEL MOIRE You can change the monitor’s color temperature.
Page 11
Customizing Your Monitor Getting Started Customizing Your Monitor Changing the on-screen display position Setting the power saving delay time Locking the controls Using the OPTION On-screen Display You can change the OSD position (for example, when you You can set the delay time before the monitor enters the The control lock function disables all of the buttons on the want to adjust the picture behind the OSD).
Page 12
Customizing Your Monitor Technical Features Getting Started Technical Features You can set the delay time before the monitor enters the Using the LANG (Language) On- Resetting the Adjustments Power Saving Function power saving mode using the OSD. Set the time according to “Setting the power saving delay time”...
Page 13
Additional Information Additional Information Getting Started Additional Information 1 The input signal condition Symptom Check these items Warning Messages “OUT OF SCAN RANGE” indicates that the input signal You cannot adjust the monitor • If the control lock function is set to on, set it to off using the OPTION OSD (page 13). is not supported by the monitor’s specifications.
Page 14
Additional Information Self-diagnosis Function Specifications This monitor is equipped with a self-diagnosis function. If Picture tube 0.25 – 0.27 mm aperture grille pitch there is a problem with your monitor or computer(s), the 19 inches measured diagonally screen will go blank and the u indicator will either light up 90-degree deflection green or flash orange.
6557-03N/03S/43N/43S SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Four screws (+ BVTP 4 x 16) Two screw covers Cabinet Seven screws (+BVTT 3 x 8) EMI shield Two screw covers Screw (+BVTT 3 x 8) Video shield Four screws (+BVTT 3 x 8) Side cover 2-2.
6557-03N/03S/43N/43S 2-5. SERVICE POSITION AC inlet (3P) CN601 D board 2-6. H BOARD REMOVAL Four screws (Tapping screw 5) Claw CN801 Two screws (+ BVTAP 3 x 12) H board Bezel...
6557-03N/03S/43N/43S 2-7. PICTURE TUBE REMOVAL Two screws Three connectors (+ BVTT 4 x 8) CN2 (DY) A board GND (DY) CN4 (DY) Anode cap Neck assy Deflection yoke Picture tube REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.
6557-03N/03S/43N/43S SECTION 3 SAFETY RELATED ADJUSTMENT When replacing or repairing the shown below table, the follow- Beam Current Protector Circuite Check ing operational checks must be performed as a safety precaution (1) Hardware logic circuit against X-rays emissions from the unit. Turn the POWER SW on, and check that the RAS- TER fades in.
6557-03N/03S/43N/43S SECTION 4 ADJUSTMENTS (µm) Landing Rough Adjustment <Specifications> 0 ± 4 0 ± 7.5 0 ± 4 1. Enter the full white signal. (or the full black dots signal). Adjust so that the green is within 2. Adjust the contrast to the maximum. the specification given right.
Page 21
Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR as a Jig D-sub mini Din 4 Pin 4 Pin...
USER CONTROL (3) Schematic Diagram of H Board STBY+5V C800 Q802 CN801 2SC3311A LED DRIVE R809 LED 0 LED 1 R810 LED 2 R812 R811 LED 3 KEY DET D806 STBY+5V SPB-26MVWF ENV_TEMP POWER R808 R807 R806 R805 R804 R803 R802 R801 R800...
6557-03N/03S/43N/43S SECTION 6 EXPLODED VIEWS • Items with no part number and no • Items marked " * " are not stocked since The components identified by shading description are not stocked because they they are seldom required for routine ¡...
6557-03N/03S/43N/43S 6-2. PICTURE TUBE Les composants identifiés per un tramé The components identified by shading 7-685-663-71 +BVTP 4X16 ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. π 7-685-881-09 +BVTT 4X8 sécurité. Ne les remplacer que par une Replace only with part number specified.
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé SECTION 7 ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. ELECTRICAL PARTS LIST piéce portant le numéro spécifié.
Page 35
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 36
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.
Page 37
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 38
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.
Page 39
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 40
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.
Page 41
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 42
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.
Page 43
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 44
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.
Page 45
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Page 46
6557-03N/03S/43N/43S The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified. piéce portant le numéro spécifié.