EGi Domos2 User Manual
Hide thumbs
Also See for Domos2:
- User manual (80 pages) ,
- Installer manual (63 pages) ,
- Instruction manual (2 pages)
Subscribe to Our Youtube Channel
Related Manuals for EGi Domos2
Summary of Contents for EGi Domos2
- Page 1 User’s Manual English 40100 www.egiaudio.com Avda. Almozara, 79 • 50003 ZARAGOZA - Spain • Phone +34 976 40 53 56 • Fax +34 976 40 53 54 • http//: www.egiaudio.com • e-mail: info@egiaudio.com Remote control...
- Page 2 E G i D O M O S 2 U n i v e r s a l EGi Audio & Domotic System. Remote Control has a LCD Please read carefully before...
-
Page 3: Table Of Contents
Code learning function Code learning process LCD Edit mode: Device buttons Delete codes and devices MACRO Function Reset to initial codes CHAPTER 4 EGi - Audio EGi - Domotics CHAPTER 5 Option settings APPENDIX A Technical specifications APPENDIX B Problem-solving chart... -
Page 4: Getting Started
1 x Pre-Programmed Code List. • 3 x AAA 1.5 V Alkaline Batteries. If the package does not include any of these components, please contact your installer or the EGi Customer Service. BATTERY ORIENTATION Open the battery lid that is on the backside of the remote control. - Page 5 40100 Remote Control will allow you to control your EGi Audio & Domotic System. You will also be able to control all home appliances, as well as your TV, DVD, audio equipment, and radio receiver with your 40100 Remote Control.
-
Page 6: Before Use
Chapter 2 Before use Before using the 40100 Remote Control, you must set it to ensure the correct transmission to the devices that are going to be controlled. The setting can be done by introducing the CODES: Manual: • Introducing the number (from the code list) assigned to the device to be controlled. •... -
Page 7: Automatic Code Selection
4 codes, and follow the steps. Assign the TV2 to any of the device buttons except DOMOTICS and EGi AUDIO; for instance, SAT/CBL. Follow the same steps as in TV1. Press the TV button any time you want to control the TV1. Press the SAT/CBL button any time you want to control the TV2. - Page 8 Press each number (2, 4, 6, 8) only once in any order. Press the button to select CODE. Press AUTO. You will listen to a beep while AUTO and OK blink. When the device (that is being controlled) turns off, press any key of the remote control.
-
Page 9: Code Learning Function
KEY, MACRO KEY and SYSTEM SETUP. Code learning process If we assume that you want to program the TV remote control on the EGi 40100 Remote Control, then put both remotes together as shown in Figure 6 and proceed as follows: Keep the CODE button pressed for 3 seconds to access to the confirmation screen. -
Page 10: Lcd Edit Mode: Device Buttons
button on the 40100 Remote Control blinks. Press the same button on the remote control until it stops blinking. Repeat the process with every blinking button and finish the copy operation. NOTE: If a code of your TV remote control already exists on the 40100 Remote Control, CODE will be displayed on the screen during the learning process. -
Page 11: Delete Codes And Devices
Delete codes and devices To delete one or all 40100 Remote Control codes, follow these steps: Keep the DELETE button pressed for 3 seconds to access to the confirmation screen. Press each number (2, 4, 6, 8) only once in any order. Navigate through the menu options using the buttons until you find the device you want to delete, then press KEY to delete the codes. -
Page 12: Macro Function
MACRO function The MACRO function (a sequence of commands of max. 60 seconds) allows you to have the control of your TV and DVD at the same time by pressing only one button on the 40100 Remote Control. You must create a sequence of commands specifying preference and time of execution of DVD, video and TV. - Page 13 EXAMPLE: If we assume that you want to turn on your TV in order to watch a film on DVD in 5 seconds, then follow these steps to set the macro: Press the TV button on the 40100 Remote Control. (This will bring you to your TV remote control menu). Press .
-
Page 14: Reset To Initial Codes
STOP MACRO COMMANDS To stop the sequence of macro commands, press first the MACRO button, and then press the EXIT button. If ERROR is displayed on the screen, the sequence is stopped. Reset to initial codes This option allows you to reset to initial codes and macros. The codes and macros that you programmed will be deleted. -
Page 15: Egi - Audio
Chapter 4 EGi - Audio 40100 Remote Control will allow you to control some audio and domotic functions of your DOMOS2 system at the touch of a button. GENERAL DOMOS2 Audio Menu. DOMOS2 Domotics Menu. AUDIO CONTROLS Turn on/off the audio of the in-wall control unit. - Page 16 Local intercom with one zone of the installation. Should you wish to talk to other zone, press the key with the number of that zone once. Get close to the in-wall DOMOS2 control unit to talk to the selected zone. You will be able to talk to the other zone for a maximum of 90” before receiving an answer.
-
Page 17: Egi - Domotics
Press the key once to finish the communication through the door entry system. Answer the door when you receive a call. Press this key once to answer the door after receiving a call and talk to the visitor. EGi - Domotics DOMOTIC FUNCTIONS SOS Alarm function. - Page 18 Domotic service (1, 2, 3, 4) for one zone. This icon indicates the domotic services for a specfic zone of the house. It activates/deactivates the domotic service associated with the number by pressing 1...4. Domotic service (7, 8, 9, 0) for the whole installation. This icon indicates the domotic services for the whole installation.
-
Page 19: Option Settings
This chapter describes the transmission function, backlight setting, and acoustic signal activation. TRANSMISSION FUNCTION You will be able to use the EGi 40100 Remote control to transmit data to other remote control of the same model. You must first connect both remote controls using a connection wire. Please see “Appendix B”... - Page 20 BACKLIGHT SETTING Learn how to activate the backlight and set the light sensor sensitivity. To activate the backlight, follow these steps: Keep the SETUP button pressed for 3 seconds to access to the confirmation screen. Press each number (2, 4, 6, 8) only once in any order. Navigate through the menu options using the buttons until you find the BACKLIGHT mode.
- Page 21 To set the light sensor sensitivity, follow these steps: Keep the SETUP button pressed for 3 seconds to access to the confirmation screen. Press each number (2, 4, 6, 8) only once in any order. Navigate through the menu options using the buttons until you find the BACKLIGHT mode.
- Page 22 ACOUSTIC SIGNAL ACTIVATION To activate the acoustic signal, follow these steps: Keep the SETUP button pressed for 3 seconds to access to the confirmation screen. Press each number (2, 4, 6, 8) only once in any order. Navigate through the menu options using the buttons until you find the BEEP mode Press the button to activate/deactivate the beep.
-
Page 23: Technical Specifications
Appendix A Technical specifications FUNCTIONS • 56 buttons on the touch-screen display. • Macro function with up to 60 sequence commands. • The backlight is automatically activated depending on the lighting in the room. • Energy-saving automatic function. • Movement detector that automatically turns on the remote control. •... -
Page 24: Problem-Solving Chart
Appendix B Problem-solving chart PROBLEMS SOLUTIONS The LCD does not display anything when The battery has run down. Check that the touching it. batteries are inserted in the correct orientation. Check that the remote control displays the correct screen to control, for instance, the TV. It will not operate over a distance of more than The remote control does not execute your 10 meters. - Page 25 Repeat the process. Make sure that you assign 1 function to each The remote control (TV, DVD, etc.) has 2 or button, when learning the codes on the EGi more functions for the same button. 40100 Remote Control. The display of the remote control automatically The LCD display turns off.
- Page 26 Notes www.egiaudio.com...
Need help?
Do you have a question about the Domos2 and is the answer not in the manual?
Questions and answers