Assembly Instructions - MTD 790 TB-TrimmerBlower Manual

Operating instruction
8. Shoulder belt holder
9. ON/OFF switch / ignition switch
10. Throttle
11. D-shaped handle
12. EZ-Link™
13. Shaft
14. Cutting attachment cover
15. Toggle
16. Toggle lock
17. Blower
18. Cutting attachment
19. Line cutting blade
20. Spacing collar
Fig. 2–3
1. D-shaped handle
2. Shaft
3. Shaft handle
4. Screw
5. Washer
6. Wingnut
7. Min distance 15.2 cm
8. Shoulder belt holder
9. Spacing collar
Fig. 4–6
(Depending on model)
1. EZ-Link™
2. Release button
3. Button
4. Guide groove
5. Main hole
6. Upper shaft tube
7. Lower shaft tube
Fig.7–8
1. Lock pin
2. Mount
3. Nut
4. Screw
Fig. 9–11
1. Throttle
2. ON/OFF switch / ignition switch
3. Full choke position (1) *
4. Half choke intermediate
position (2) *
5. Operating position (3) *
6. Choke lever *
7. Intake pump/primer
8. Starter rope
* Depending on model
Fig. 13–14
1. Toggle
2. Toggle lock
Fig. 19–20
1. Choke lever
( Depending on model)
2. Screw
3. Air filter
Fig. 24–25
1. Idle speed controller
2. Spark plug
Installation manual
Installing the D-shaped handle
For your safety the D-shaped
n
handle must be installed before
the distance collar. Push down
the handle bar over the shaft
so that the handle is at angle
to the engine (Fig. 2).
'EYXMSR
(S RSX TYWL XLI (WLETIH LERHPI
FEV SZIV XLI HMWXERGI GSPPEV
3XLIV[MWI XLI LERHPI FEV SV YRMX
QE] FI HEQEKIH
Attach and tighten bolt, washer
n
and wing nut.
Adjusting the D-shaped
handle
Loosen the wing screw. It is not
n
required to remove the screws
and the washer.
Rotate the D-shaped handle
n
until the handle is positioned over
the shaft. Minimum distance
15.2 cm (Fig. 2).
While holding the unit in the
n
operating position (Fig. 12), move
the D-shaped handle into the
position which ensures the best
possible handling of the unit and
tighten the wing screw (Fig. 2).
Attaching and adjusting
the shoulder belt (Depending
on model)
Pull the belt through the buckle.
n
Pull the shoulder belt over your
n
head and place the pad on your
shoulder.
Latch the hook of the shoulder
n
belt into the metal holder (Fig. 3).
Adjust the belt to a comfortable
length.
Using the EZ-LINK
Note
To facilitate installation and removal
of attachments, place the unit on the
ground or a workbench.
Removing cutter/blower
and other attachments
To loosen the attachment, rotate
n
the screw handle (3) to the left
(Fig. 6).
Press and hold down the release
n
button (2) (Fig. 4).
Hold the upper shaft housing (7)
n
securely and pull the attachment
directly out of the EZ-Link
coupling (Fig. 5).
Installing the cutter/blower
and other attachments
To loosen the attachment, rotate
n
the screw handle to the left
(Fig. 6).
Hold the attachment securely and
n
push directly into the EZ-Link
coupling (Fig. 5).
Note
Alignment of the release button (2)
with the guide groove (4) facilitates
installation (Fig. 4).
Secure the attachment by rotating
n
the button (3) to the right (Fig. 6).
Before operating the unit, ensure
that the rotary handle is secure.
Installing the cutter
attachment cover
Attach the cover with the guide
n
hole over the lock pin (1; Fig 7).
Align the cover so that its holes
n
agree with those in the locking
sleeve.
Attach the cover to the mount with
n
the screw (4) on the right and the
nut (3) on the left (Fig 8).
Check that the connections
n
sit tightly and correctly.
English
TM
system
TM
TM
7