Table of Contents
Advertisement
Quick Links
All rights reserved by Janz Tec AG.
No parts of this technical manual may be modified, copied or reproduced
in any form or by any means for commercial use without the prior written
permission of Janz Tec AG, Germany.
All instructions, information and specification contained in this manual
are for reference only and remain subject to change without
announcement.
Fanless Embedded PC System Intel ATOM Processor
PROPRIETARY NOTICE
emPC-X1600
emPC-X1100
(Hardware Manual)
Version 1.1
refers to product revision no.
V 1.4/1.1
Advertisement
Table of Contents
Related Manuals for Janz Tec emPC-X1600
Summary of Contents for Janz Tec emPC-X1600
- Page 1 PROPRIETARY NOTICE All rights reserved by Janz Tec AG. No parts of this technical manual may be modified, copied or reproduced in any form or by any means for commercial use without the prior written permission of Janz Tec AG, Germany.
- Page 2 Title: File: j:\as\entwicklung\projekte\hw\empc\empc_x1600\doc\manual\manual_empc- x1600_hardware.doc Pattern: z:\text\vorlagen\normal.dot Created: Stefan Althöfer, 21.06.2011 Last Update: Stefan Althöfer, 22.03.2013 © Janz Tec AG 2013 Im Dörener Feld 8 D-33 100 Paderborn, Germany Tel.: +49-5251-1550-0 FAX: +49-5251-1550-190 email: support@janztec.com Internet: www.janztec.com...
-
Page 3: Table Of Contents
Ethernet Interface ETH0 ....................12 Ethernet Interface ETH1 ....................12 System Internals Appendices Technical Data ........................14 References........................16 Product History........................17 6.3.1 emPC-X1600 (/0, /1, /2) ....................17 6.3.2 emPC-X1100 ....................... 17 Manual History ........................18 Rev. 1.1 © Janz Tec AG... - Page 4 Figure 5: Power connector ........................10 figure 6: System Block diagram......................13 List of Tables Table 1: emPC-X1600 standard products ....................5 Table 2: Interfaces connected to D-SUB....................9 Table 3: Power connector assignment ....................10 table 4: RS232 (Console) connector ..................... 10 table 5: RS232 connector ........................
-
Page 5: About This Manual
(Hardware Manual) • Contents About this Manual This is the hardware manual for the emPC-X1600 embedded PC. It starts with an introduction to the emPC-X1600. After that it discusses some topics about installation of the product. The rest of the manual then covers technical details about the emPC-X1600. -
Page 7: Introduction
1 - 5 Introduction The emPC-X1600-Platform is a flexible computer system. It consists of one CPU board and can be expanded with a variety of IO expansion boards. The boards are stacked together and are inserted into a rail mounted housing. This allows flexible system building. Internal busses are documented, so users can build application specific IO expansion boards. -
Page 8: Hardware Customization
• Power supply monitor 1.1.2 Hardware Customization Due to it’s flexible system architecture, the emPC-X1600 can be easily customized if the standard products do not provide optimum features or price. Customization is possible even at moderate quantities. Ask sales department for details. -
Page 9: Safety Instructions
(Hardware Manual) • Safety Instructions 2 - 7 Safety Instructions Refer to page iii for explanation of the warning notice system. The product described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation for the specific task, in particular its warning notices and safety instructions. -
Page 10: Installation/Maintenance
BIOS. cFast Card Removal Due to space limitations for the emPC-X1600, there is no opening in the housing for the internal cFast Flash card on the CPU module. For removing the cFast Flash card the housing of the emPC-X1600 must be opened. Therefore the back panel of the housing must be removed by removing the two screws –... -
Page 11: Interfaces
4 - 9 Interfaces The emPC-X1600 is equipped with differing interfaces. The following interfaces are common for all systems: DVI-D, 3 x USB 2.0, 1 x 10/100 Mbit/s Ethernet and 1 x 10/100/1000 Mbit/s Ethernet. Depending on which alternative was ordered additional interfaces are available. The following table shows what alternatives are possible. -
Page 12: Power Supply, Reset And Power Led
(Hardware Manual) • Interfaces 4 - 10 Power Supply, Reset and Power LED The power supply connector is implemented with a Phoenix Contact Plug type MC1,5/3-ST1F-5,08 BF and is included in delivery. The assignment of this connector is shown in Figure 5 and Table 3. -
Page 13: Can
(Hardware Manual) • Interfaces 4 - 11 table 5: RS232 connector RS485 In the RS485 variant, there are only the differential signals D+ and D- provided. The transceiver is enabled to send data, when RTS# of the corresponding UART is low. Data received on the RS485 will always be seen on the UART’s RxD input. -
Page 14: Usb Type A Receptacle Usb0, Usb1 And Usb2
(Hardware Manual) • Interfaces 4 - 12 USB type A receptacle USB0, USB1 and USB2 Two USB 2.0 interfaces are available at the front panel. 1 +5V, I = 500 mA 2 USB- 3 USB+ 4 GND table 9: USB connector... -
Page 15: System Internals
(Hardware Manual) • System Internals 5 - 13 System Internals The emPC-X1600 is built upon a couple of standard building blocks, as shown in figure 6. expansion cFAST ixBus Q7 Carrier ixBus Power Supply and Socket Communication Module Q7 Module... -
Page 16: Appendices
(Hardware Manual) • Appendices 6 - 14 Appendices Technical Data Type X1600: Intel Atom Z530 X1100: Intel Atom Z510 Clock Frequency 1.6 GHz 1.1 GHz Front Side Bud 533 MHz 400 MHz Hyper Threading L1-Cache 32 kB instruction, 24 kB data... - Page 17 (Hardware Manual) • Appendices 6 - 15 Power Supply Input 9..32 V DC SELV consumption 15 W (max) inverse-polarity protection Yes Fuse Internal melting fuse in DC in, GND is unfused potential separation No, GND (Pin 3 in Table 3) is connected to case...
-
Page 18: References
(Hardware Manual) • Appendices 6 - 16 References These references direct you to manuals and specifications that you need to when developing programs for the emPC/X1600. Most of the documents can be downloaded from the Internet. Look for the WWW servers of the chip/component manufacturers. -
Page 19: Product History
(Hardware Manual) • Appendices 6 - 17 Product History 6.3.1 emPC-X1600 (/0, /1, /2) Version Release Name Changes Date • initial version V1.0 • V1.1 11.08.2011 optional cFast socket • optimized USB connector position • V1.2 23.05.2012 improved CPU cooling with monolithic cooling block •... -
Page 20: Manual History
(Hardware Manual) • Appendices 6 - 18 Manual History Version Release Name Changes Date • Initial release V1.0 26.08.2011 • Changed to Janz Tec V1.1 13.03.2013 • Restructured technical data • Added total power limitation for USB connectors • Fixed missing GND for RS232 connector •...