Table of Contents
Advertisement
Quick Links
PROPRIETARY NOTICE
All rights reserved by Janz Tec AG.
No parts of this technical manual may be modified, copied or reproduced
in any form or by any means for commercial use without the prior written
permission of Janz Tec AG, Germany.
All instructions, information and specification contained in this manual
are for reference only and remain subject to change without
announcement.
emPC-X
embedded PC
(Hardware Manual)
Version 1.2
refers to product revision no.
1.0
Advertisement
Table of Contents
Related Manuals for Janz Tec emPC-X Series
Summary of Contents for Janz Tec emPC-X Series
- Page 1 PROPRIETARY NOTICE All rights reserved by Janz Tec AG. No parts of this technical manual may be modified, copied or reproduced in any form or by any means for commercial use without the prior written permission of Janz Tec AG, Germany.
- Page 2 Title: emPC-X embedded PC File: j:\as\entwicklung\projekte\hw\empc\empc_x1600\doc\manual\manual_empc- x_hardware.doc Pattern: \\ntserv5\janzgrp\as\entwicklung\formulare\entwicklung (ew)\ew_manual.dot Created: Stefan Althöfer, 21.05.2014 Last Update: Stefan Althöfer, 13.02.2019 © Janz Tec AG 2015 Im Dörener Feld 8 D-33100 Paderborn, Germany Tel.: +49-5251-1550-0 FAX: +49-5251-1550-190 email: support@janztec.com Internet: www.janztec.com...
-
Page 3: Table Of Contents
USB type A receptacle (USB0, USB1 and USB2) ............15 RS232 (Console)........................15 RS232 ..........................16 RS485 ..........................16 CAN ............................17 SD Card ..........................18 Maintenance CFast Card Replacement ....................19 Battery Replacement ......................20 Appendices Technical Data ........................21 References .........................23 Dimensions ........................24 Product History........................25 Manual History ........................25 Rev. 1.2 © Janz Tec AG... - Page 4 4: DVI-D connector ........................14 table 5: Ethernet connector ........................15 table 6: USB connector ...........................15 table 7: RS232 (Console) connector ......................15 table 8: RS232 connector ........................16 table 9: RS485 connector ........................16 table 10: CAN connector ........................17 © Janz Tec AG Rev. 1.2...
- Page 5 There exist some isolated reference grounds for communication interfaces or IO. These reference signals are referred to as GND-x, where x indicates function. SELV Safety extra low voltage. Rev. 1.2 © Janz Tec AG...
-
Page 7: Introduction
DVI-D graphic interface on front panel (Single Link) • Single channel LVDS on internal connector • 2 x 10/100/1000 Mbit/s Ethernet • 3 x USB 2.0 interface (480Mbit/s) • Battery backed up RTC • System Power supply 9..34 VDC Rev. 1.2 © Janz Tec AG... -
Page 8: Hardware Customization
More CAN ports are possible by using expansion cards (in a larger housing) • More serial ports are possible • Digital/Analog-IO expansion card • Customer specific expansion cards • Other mounting options (e.g. flange mount) © Janz Tec AG Rev. 1.2... -
Page 9: Software
(Hardware Manual) • Introduction 1 - 7 1.1.3 Software Supported by • Windows 7, Windows 8 • Windows 7 Embedded Standard • Linux Contact Janz Tec for more information about the available software packages. Rev. 1.2 © Janz Tec AG... -
Page 10: Functional Overview
Janz Tec ix-Bus power supply and communication module • Optionally additional IO modules Refer to Congatec documentation for details on the Q7 Module. Refer to Janz Tec ixBus System Reference Manual for details on the Janz Tec specific building blocks. © Janz Tec AG Rev. 1.2... -
Page 11: Safety Instructions
Do not operate the product beyond the specified ambient conditions. Do not cover the vent slots of the product. NOTICE: EMI This product is a class A device. This product may cause radio interference. In this case the user must take adequate measures. Rev. 1.2 © Janz Tec AG... -
Page 12: Intended Use
All Janz Tec products are registered as B2B custom at the german EAR. Hence Janz Tec products must not be disposed to public collection points for used electronic equipment. Refer to §14 of General Terms & Conditions of Janz Tec AG for the details regarding the mutual obligations as to the disposal of Janz Tec products. -
Page 13: Installation
Do not operate the product beyond the specified ambient conditions. Do not cover the vent slots of the product. Install the product such that the venting holes at the top and bottom of the housing are not blocked. Rev. 1.2 © Janz Tec AG... - Page 14 At light loads, the mounting conditions might be relaxed. It is recommended to check the cooling conditions in the user application. Temperature sensors are available inside the emPC-X. © Janz Tec AG Rev. 1.2...
-
Page 15: Connectors And Operators
Reset Serial-1 Serial-0 Serial Figure 3: emPC-X/0 interfaces Figure 4: emPC-X/1 interfaces Ethernet Ethernet Power Power 24VDC Reset CAN-3 CAN-2 24VDC Reset CAN-1 CAN-0 CAN-1 CAN-0 Figure 5: emPC-X/2 interfaces Figure 6: emPC-X/4 interfaces Rev. 1.2 © Janz Tec AG... -
Page 16: Power In
DDC clock 18 TMDS 0+ DDC data 19 SHIELD 20 N/C TMDS 1- 21 N/C 10 TMDS 1+ 22 SHIELD 11 SHIELD 23 TMDS C+ 12 N/C 24 TMDS C- table 4: DVI-D connector © Janz Tec AG Rev. 1.2... -
Page 17: Ethernet Interfaces (Ethernet1 And Ethernet2)
The connector is a standard 9 pin D-SUB plug, but the interface is connected with four wires only, table 7 shows the pin out. 1 n.c. n.c. 2 RxD 3 TxD 4 n.c. n.c. 9pin male D-Sub 5 GND table 7: RS232 (Console) connector Rev. 1.2 © Janz Tec AG... -
Page 18: Figure 8: Rs485 Signaling
In the RS485 variant, there are only the differential signals D+ and D- provided. The transceiver is enabled to send data, when RTS# of the corresponding UART is low. Hardware can be customized to either receive or not-receive (standard) the transmitted data on the UART’s RxD input. Ask Janz Tec for customization regarding this option. -
Page 19: Can
1 n.c. 2 CANL CANH 3 GND n.c. 4 n.c. VEXT 9pin male D-Sub 5 n.c. table 10: CAN connector This signal is optionally available to provide power to supply an external transceiver module Rev. 1.2 © Janz Tec AG... -
Page 20: Sd Card
However, ensure that the operating system is ready for card removal before you push the card. Otherwise, you might lose data. To install the SD card push it into the socket until the card locks. Then install the cover. © Janz Tec AG Rev. 1.2... -
Page 21: Maintenance
10: emPC-X back panel removal CFast Card Replacement NOTICE Power must be turned off before removing or inserting the CFast card Refer to figure 10 to identify the location of the CFast card. Rev. 1.2 © Janz Tec AG... -
Page 22: Battery Replacement
2. Insertion: Align new battery to the left side of the holder and gently press down on the right side of the battery until the battery snaps into the holder. figure 11: Removing and replacing coin cell battery © Janz Tec AG Rev. 1.2... -
Page 23: Appendices
2 programmable LEDs (S0 – red and S1 - green) User LEDs System Housing galvanized steel sheet, outside painted Battery CR 2032, for real time clock Temperature Sensor Accessible via Qseven module I2C Watchdog Yes, implemented in Qseven module Rev. 1.2 © Janz Tec AG... - Page 24 IP20 Physical Dimensions Size (WxHxD) Including connectors and rail mounting bracket 2 DSUB: 65.0 x 115.5 x 116.0 mm 4 DSUB: 82.6 x 115.5 x 116.0 mm Weight 2 DSUB: 830 g 4 DSUB: © Janz Tec AG Rev. 1.2...
-
Page 25: References
Most of the documents can be downloaded from the Internet. Look for the WWW servers of the component/chip manufacturers. SJA1000 Product specification, Philips Semiconductor, Jan 04, 2000 ixBus System Reference Manual, Janz Tec AG WWW-References Janz Tec AG www.janztec.com... -
Page 26: Dimensions
W = 62,50 mm 5,50 mm 8,50 mm figure 12: housing dimensions (2 DSUB system shown) emPC-X Systems with different IO options just differ in dimension W Slot Variant 2 DSUB 62.5 mm 4 DSUB 80.1 mm © Janz Tec AG Rev. 1.2... -
Page 27: Product History
• Added additional notes to the section “Mounting” • Changed housing colours in illustrations V1.2 2019-02-12 • Changed RS485 self-receipt to non-standard behaviour • Updated battery replacement section • Added sections intended use and disposal and recycling • Rev. 1.2 © Janz Tec AG...