Nokia Lumia 930 RM-1045 Service Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

Service Manual for L1 and L2

Nokia Lumia 930

RM-1045

Key features

2.2 GHz Quad core processor



5" Full-HD OLED Display



32 GB Internal memory



20 MP Nokia PureView camera



Integrated wireless charging



Version 1.0

CHECK THE REPAIR

POLICY BEFORE

PERFORMING ANY

MECHANICAL REPAIR ON

SERVICE LEVEL 1&2!

Assembly hints

Product Controls And Interfaces

Exploded View

Solder Components

Service Concept

Send feedback

Recommend Change in



KICS

Rate this page in KICS



E-mail



careacademy@nokia.com

Disassembly Steps

Service Devices

Phone Reset

Table of Contents

Summary of Contents for Nokia Lumia 930 RM-1045

Page 1 2.2 GHz Quad core processor   E-mail 5" Full-HD OLED Display   careacademy@nokia.com 32 GB Internal memory  20 MP Nokia PureView camera  Integrated wireless charging  Version 1.0 Exploded view Disassembly steps CHECK THE REPAIR POLICY BEFORE PERFORMING ANY MECHANICAL REPAIR ON SERVICE LEVEL 1&2!
Page 2 Service Manual Level 1 and 2 Version history Nokia Lumia 930 RM-1045 Version 1.0 Version Date Description 29.05.2014 First published version ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 3 Service Manual Level 1 and 2 Exploded view Nokia Lumia 930 RM-1045 Version 1.0 CARE UI ASSEMBLY CAMERA KEY I0007 (I0002 - I0016) MAIN ANTENNA LTE COAX FLEX I0005 DISPLAY WINDOW I0002 LOCK KEY I0008 DISPLAY I0003 VOLUME KEY I0009...
Page 4 ENGINE COVER ASSEMBLY MAIN ANTENNA LTE (I0041 - I0045) I0044 MAIN ANTENNA VOICE I0045 GPS/WLAN ANTENNA I0042 IHF SPEAKER ASSEMBLY I0041 MIMO ANTENNA I0043 SCREW TORX+ SIZE 4 M1.4 X 3.8 I0034 LED FLASH I0049 WIRELESS CHARGING NFC ANTENNA ASSEMBLY I0051 I0050 BACK COVER ASSEMBLY...
Page 5 SS-319 RF-connector disassembly/assembly tool and an AV jack. Note that the device shown in most of these pictures is the Nokia Lumia Icon. On those steps the spare parts and the disassembly procedures are the same.
Page 6 3) Open the SIM TRAY with the SS-93 and pull it out. 4) At this point, if you only want to check the TYPE LABEL without having to disassemble the phone, you can pull the LABEL TRAY out with the hook on the SIM TRAY. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 8 7) Unscrew the TORX+ SIZE 4 screw on top of the BATTERY CONNECTOR STRAP. Do not use the screw again. Discard it. 8) Remove the BATTERY CONNECTOR STRAP with tweezers. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 9 9) Disconnect the BATTERY connector with the SS-93. Be careful not to damage the connector. 10) Unscrew the ten TORX+ SIZE 4 screws in the order shown. Do not use the screws again. Discard them. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 10 11) Release the ENGINE COVER ASSEMBLY from the shown place with the SS-93. 12) Lift up and remove the ENGINE COVER ASSEMBLY top end first. Be careful not to damage the antenna spring contacts on the bottom of the ENGINE COVER ASSEMBLY. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 11 13) Remove the HEAT SPREADER with tweezers. Do not use it again. Discard it. Note that the HEAT SPREADER needs to be removed completely ONLY when the ENGINE BOARD requires repair work. 14) Release the BATTERY from the shown place with the SS-93. Be careful not to damage the two flexes located under the BATTERY.
Page 12 15) Remove the BATTERY. 16) Disconnect the SKYPE CAMERA connector from the shown edge with the SS-93. Be careful not to damage the connector or any components nearby. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 13 17) Remove the SKYPE CAMERA with tweezers. 18) Disconnect the six shown connectors with the SS-93. Be careful not to damage the connectors or any components nearby. Note that the SS-319 can also be used to disconnect the connectors. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 14 19) Release the RF CABLE connector with the SS-319. Lock the SS-319 to the top of the connector as shown and lift it up carefully. Be careful not to damage the connector. 20) Release also the other end of the RF CABLE and remove it. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 15 21) Pull the LTE ADHESIVE to the direction shown to remove it under the LTE FLEX. Do not use it again. Discard it. 22) Release the ENGINE BOARD from the shown place with the SS-93. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 16 23) Lift up the other side and remove the ENGINE BOARD to the direction shown. 24) Disconnect the CAMERA connector from the shown edge with the SS-93. Be careful not to damage the connector or any components nearby. Remove the CAMERA. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 17 25) Release the DAUGHTER ENGINE BOARD from the shown place with the sharp end of the SS-93. 26) Remove the DAUGHTER ENGINE BOARD. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 19 29) If the UI ASSEMBLY or the flexes are being reused, peel off and discard any adhesive residue. 30) Release the EARPIECE with the SS-93 and remove it with tweezers. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 20 31) Remove and discard the EARPIECE GASKET with the dental tool. Be careful not to injure yourself with the sharp end of the dental tool. 32) Push out the LABEL TRAY with the SS-93 and remove it. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 21 33) Use an AV jack to lift up the HSJ ASSEMBLY. 34) Release the HSJ ASSEMBLY flex with the SS-93 and remove the HSJ ASSEMBLY. Do not use it again. Discard it. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 23 37) Release the VIBRA and the VIBRA flex with the SS-93. Remove the VIBRA ASSEMBLY. 38) If the UI ASSEMBLY or the VIBRA ASSEMBLY are being reused, remove and discard any adhesive residue. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 24 39) Remove and discard the DAUGHTER ENGINE BOARD GASKET only if it is damaged. 40) Release the PRIMARY MIC FLEX with the dental tool and remove it with tweezers. Do not use it again. Discard it. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 25 41) Remove and discard the PRIMARY MIC FLEX ADHESIVE from the UI ASSEMBLY with tweezers. 42) Peel off and discard the SMALL BATTERY ADHESIVE using SS-93 and tweezers. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 26 43) Peel off and discard the BATTERY ADHESIVE using SS-93 and tweezers 44) Release the WIRELESS CHARGING ASSEMBLY with the SS-93. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 27 45) Remove the WIRELESS CHARGING ASSEMBLY. Do not use it again. Discard it. 46) Push the LED FLASH from the back side with the SS-93 and remove it with tweezers. Remove any adhesive remains from the LED FLASH. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 28 47) Release the NFC ANTENNA with the SS-93. Start from the corner. 48) Remove the NFC ANTENNA. Do not use it again. Discard it. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 29 49) Remove and discard the two BACK COVER GASKETS with tweezers. 50) The Nokia Lumia 930 disassembly procedure is complete. -END OF DISASSEMBLY- ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 30 RM-1045 Version 1.0 Note that the device shown in most of these pictures is the Nokia Lumia Icon. On those steps the spare parts and the assembly procedures are the same. 1) To assemble the PRIMARY MIC FLEX, first place the PRIMARY MIC GASKET on the microphone. Make sure the shown hole aligns with the microphone hole.
Page 31 3) Remove also the protective film from the PRIMARY MIC FLEX. 4) Place the PRIMARY MIC FLEX ADHESIVE to its slot in the UI ASSEMBLY. Use the shown holes to get the right alignment. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 32 5) Press gently with the SS-93 to activate the adhesive and peel off the protective film. 6) Place the PRIMARY MIC FLEX to its place. Use the holes to get the right alignment. Press gently to activate the adhesive. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 33 7) Place the BATTERY ADHESIVE as shown on the UI ASSEMBLY. Use the shown holes to get the right alignment. 8) Press all around the ADHESIVE... ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 34 9) ... and peel off the protective film. 10) Place the SMALL BATTERY ADHESIVE as shown on the UI ASSEMBLY. Use the shown holes to get the right alignment. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 36 13) Start assembling the VIBRA ASSEMBLY by first placing the VIBRA BOOT on it as shown. 14) Place the VIBRA ASSEMBLY to its slot on the UI ASSEMBLY. First align the flex to its place, then lower down the VIBRA. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 37 15) Gently press the flex and the VIBRA from the shown place to activate the adhesive. 16) To assemble the MIMO COAX FLEX and the JUMPER FLEX, first place them on the SS-327 flex assembly jig. Use the guiding pins to get the right placement. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 38 17) Place the MIMO COAX FLEX ADHESIVE on the MIMO COAX FLEX. Press firmly to activate the adhesive and remove the protective film. 18) Place the JUMPER FLEX ADHESIVE on the JUMPER FLEX. Press firmly and remove the protective film. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 39 19) Before placing the UI ASSEMBLY on the jig check once more that the flexes are positioned on the jig as shown. Check also that the top side of the UI ASSEMBLY is facing the shown side of the jig as shown. 20) Then place the UI ASSEMBLY on the jig and press it gently but properly to get the flexes attached.
Page 40 21) Remove the UI ASSEMBLY from the jig and check that the flexes are properly attached. 22) Assemble the DAUGHTER ENGINE BOARD to the UI ASSEMBLY shown side first. Align the two shown pogo pins to their places. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 41 23) Then lower down the DAUGHTER ENGINE BOARD and press down to attach the shown clip. Be careful not to damage the DAUGHTER ENGINE BOARD or any of its componets. 24) When assembling the CAMERA use the SS-327 flex assembly jig as a steady platform. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 42 25) Connect the CAMERA to the ENGINE BOARD with the SS-93. Be careful not to damage the connector or any components nearby. 26) Then fold the CAMERA flex as shown. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 43 27) Start assembling the ENGINE BOARD to the UI ASSEMBLY shown side first and align the CAMERA to its socket. 28) Lower down the ENGINE BOARD and press to attach the shown clip. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 44 29) After assembling the ENGINE BOARD check the tactility of the side keys. 30) Place the LTE ADHESIVE to its place. Use the guiding lines on the ENGINE BOARD to get the right placement. Remove the protective film from the LTE ADHESIVE. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 45 31) Place the SKYPE CAMERA GASKET to the shown slot on the SS-327 jig. 32) Place the SKYPE CAMERA on top of the gasket as shown and press it gently to activate the adhesive. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 46 33) Remove the SKYPE CAMERA fom the jig and remove the protective film from the SKYPE CAMERA GASKET. 34) Place the HEAT SPREADER on the ENGINE BOARD as shown. Use the edges of the shielding lids to get the right alignment. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 47 35) Press all around the HEAT SPREADER to activate the adhesive. 36) Remove the protective film and gently press all around the HEAT SPREADER again to make sure its properly attached. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 48 37) Fasten the ten TORX+ SIZE 4 screws in the order shown to the torque of 13 Ncm. 38) Fasten the TORX+ SIZE 4 screw to the top of the BATTERY CONNECTOR STRAP to the torque of 13 Ncm. ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 51 Service Manual Level 1 and 2 Solder components Nokia Lumia 930 RM-1045 Version 1.0 Volume up Volume down Power Grounding Camera Grounding Grounding switch switch switch spring switch spring spring S4403 S4402 S4401 S4400 X1002 X1004 Camera fuse F1401 Fuse...
Page 52 SS-327 Flex assembly jig Nokia Standard Toolkit (v2) disassembly/assembly tool For more information, refer to the Service Bulletin (SB-011) on Nokia Online. Supplier or manufacturer contacts for tool re-order can be found in “Recommended service equipment” document on Nokia Online.
Page 53 Service Manual Level 1 and 2 Product controls and interfaces Nokia Lumia 930 RM-1045 Version 1.0 1 — Nano-SIM holder 2 — 3.5mm Headset connector 3 — Earpiece 4 — Front camera 5 — Ambient light & Proximity sensor 6 — 2nd Microphone 7 —...
Page 54 Service Manual Level 1 and 2 Service concept Nokia Lumia 930 RM-1045 Version 1.0 Flashing concept Service CA-101 software Note: Charged battery is mandatory Transceiver with embedded battery ©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.
Page 55 Service Manual Level 1 and 2 Phone reset Nokia Lumia 930 RM-1045 Version 1.0 Hardware reset If the phone hardware is jammed, you should first recommend that the consumer performs a hardware reset. The hardware reset does not reset the Windows Live ID or remove any consumer data. Because the...
Page 56 Option 2: Hardware key combination - Use this option if the phone is locked and the consumer does not know the code - Note: no warning about data loss! - Do not advertise this feature to consumers! Follow next steps to perform OS reset with phone keys. Step 1 Make sure the phone is turned Off.

Nokia Lumia 930 RM-1045 Service Manual

Quick Links

Related Manuals for Nokia Lumia 930 RM-1045

Summary of Contents for Nokia Lumia 930 RM-1045

Table of Contents