Alarm In; Video Loss Detect; Alarm Set/ Reset Sw - KTL cctv DVR 9010 User Manual

Condition 1 Set Up/ Condition 2 Set UP
This menu allows you to setup each camera's motion detected area
and sensitivity. First select the wanted camera by using the right and
left direction buttons, and then move the cursor to the second and
third items to setup the chosen camera's detect area and sensitivity.
Detect Area
This item allows you to set the detection area for each camera. The
detection area consists of 192 (16x12) detection grids.
Use the DIRECTION buttons to select each grid, and press ENTER to
enable or disable the grid. Or, you can select all grids by press SET.
You can also press MODE to change the size of the cursor.
◎
◎
: disabled : enabled
Sensetivity
This item allows you to set the triggered level for the alarm.
The first bar shows the current detected amount of motion of this
camera. The second bar allows you to set the triggered level, once
the detected motion amount becomes larger than this level; the alarm
will be triggered.

6.7.4 Alarm In

This menu allows you to enable/ disable the Alarm pins of external I/O
connector and to select N.O. (normal open) or N.C. (normal close)
type for each pin.
Alarm In Detect
This item allows you to enable (YES) or disable (NO) the Alarm In pins.
Configuration Table
This item allows you to select N.O. (normal open) or N.C. (normal close) type for each Alarm In
pins. Please refer to section 5.7.3 for the table.

6.7.5 Video Loss Detect

This item allows you to enable/ disable the DVR to detect Video Loss as an
alarm event.

6.7.6 Alarm Set/ Reset SW

This item allows you to enable/ disable the Alarm Set/ Reset signal of the external connector. If
you select EN (enable), then you can force the alarm output to on/ off by using Alarm Set signal.
00-37963-ACEB4 22
Condition Set Up
1 Se ect l Camera 1
2 Detect Area
3 Sens tivity i
4 Exit
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎
Motion Detect
Threshold
Alarm In
1 A arm In Detect l
2 Configuration Table
3 Exit
◎ ◎
◎ ◎
◎ ◎
◎ ◎
◎ ◎
◎ ◎
◎ ◎
◎ ◎
OFF