Related Manuals for build MH00330G
Summary of Contents for build MH00330G
- Page 1 MODEL #. MH00330G MH00336G Installation, Use and Care Guide READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.build.com...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifi cations ........... Mounting the Hood ........9 Ductless Recirculating ..........FEATURES & CONTROLS Mechanical Controls ..........MAINTENANCE Hood and Filter Cleaning .........
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product. A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary. MH00330G / MH00336G - MAX 426 Watts, 3.5 Amps... -
Page 6: Hardware Package Contents
MODELS: MH00330G & MH00336G PARTS SUPPLIED 1 - Hood with internal blower 1 - Duct cover wall bracket 1 - Duct cover assembly (top and bottom) 1 - 6” round backdraft damper (pre-installed) 2 - 50W GU-10 halogen light bulbs (pre-installed) - Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8”...
-
Page 8: Damage - Shipment/Installation
Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than min. ducted 23” 34”. min. recirc. 27” max. 42” It is important to install the hood at the proper mounting height. - Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certifi...
- Page 10 ” ” Min. Ducted - 23” Min. Recirc. - 27” Maximum - 42” ” 15/16 ” 30” or 35 ” 3/16 FRONT SIDE ” 15/16 ” ” 15/16 BACK...
- Page 11 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. (26” minimum from range top) . 2. Plum and mark center line. Duct Cover Bracket 3.
- Page 12 Kit includes charcoal lters, charcoal lter brackets and air diverter plate. Hood Model Part No. Filters in Pkg. MH00330G / MH00336G RHRK003S 1. Purchase recirculating kit per the part number above 2. Secure air diverter plate to wall below duct cover bracket. (FIG. B) Run 6”...
- Page 13 Blower Off Lights On/Off Blower Speed Selection Blower Off The blower will be powered off by pressing: Blower Speed Selection Select one of three speed levels by pressing: Lights On/Off Power lights on and off by pressing:...
-
Page 14: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. -
Page 15: Replacing Light Bulbs
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. - Page 16 TROUBLESHOOTING PROCEDURES FOR MH00330G & MH00336G After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 17 MH00330G / MH00336G...
- Page 18 DESCRIPTION PART# Replacement Parts Light Bulb GU-10 50W (each) Z0B-0020 Optional Accessories Recirculating Kit RHRK003S Replacement Charcoal Filter RHCF001 Duct Cover Extension (up to 12’ ceiling) RHEX003S To order parts, email us at vsupport@ventingservices.com or call us at 1.888.750.1698...
- Page 19 STAPLE YOUR RECEIPT HERE Proof of the original purchase Limited Warranty date is needed to obtain service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-750-1698 Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...