Related Manuals for build MISENO MH00230G
Summary of Contents for build MISENO MH00230G
- Page 1 MODEL # MH00230G MH00236G Installation, Use and Care Guide READ AND SAVE THESE INSTRUCTIONS 2014.OCT...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hoo Speci cations ........... Mounting the Hood ............. Ductless Recirculating ..........FEATURES & CONTROLS Mechanical Controls ..........MAINTENANCE Hood and Filter Cleaning .........
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. NOT FOR USE IN OUTDOOR COOKING ENVIRONMENTS. CAUTION To reduce risk of re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. -
Page 6: Hardware Package Contents
MODELS: MH00230G, MH00236G PARTS SUPPLIED 1 - Hood with internal blower 1 - Duct cover wall bracket 1 - Duct cover assembly (top and bottom) 1 - 6” round backdraft damper (pre-installed) 2 - 50W GU-10 halogen light bulbs (pre-installed) 1 - Stainless steel mesh filter 1 - Canopy, glass 1 - Hardware package... - Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8”...
-
Page 8: Damage - Shipment/Installation
Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than 34”. * Min. ducted (A) Min. recirc. (B) It is important to install the hood at the proper Max. - Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certi ed Silver Tape or Duct Tape.
- Page 10 ” ” Min. Ducted - 22” Min. Recirc. - 26” Maximum - 42” 11/16 ” ” 30” or 35 ” 7/16 FRONT SIDE 15/16 ” ” 15/16 ” BACK...
- Page 11 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. 26” minimum from range top . 2. Plum and mark center line. Duct Cover Bracket 3.
- Page 12 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and ltered by a set of optional charcoal lters. The air is then puri ed and re- circulated back within the home.
- Page 13 Blower Off Lights On/Off Blower Speed Selection Blower Off The blower will be powered off by pressing: Blower Speed Selection Select one of three speed levels by pressing: Lights On/Off Power lights on and off by pressing:...
-
Page 14: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. -
Page 15: Replacing Light Bulbs
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. -
Page 16: Troubleshooting Procedures
TROUBLESHOOTING PROCEDURES Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2. - Page 17 MH00230G/236G 3.3A...
- Page 18 DESCRIPTION PART# Replacement Parts Light Bulb GU-10 50W each Z0B-0020 Optional Accessories Recirculating Kit RHRK002S for RH002 Replacement Charcoal Filter RHCF001 Duct Cover Extension up to 12’ ceiling RHEX003S Order replacement parts from us by calling 1.888.750.1698...
- Page 19 STAPLE YOUR RECEIPT HERE Proof of the original purchase Limited Warranty date is needed to obtain service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-750-1698 Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...