Related Manuals for build MISENO MH70230AS
Summary of Contents for build MISENO MH70230AS
- Page 1 MODEL #. MH70230AS MH70236AS MH70248AS Installation, Use and Care Guide READ AND SAVE THESE INSTRUCTIONS 2014.NOV...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options .......................... Electrical ................. Mounting the Range Hood ........Horizontal Ducting Conversion ......FEATURES & CONTROLS Rotary Dial ..............MAINTENANCE Cleaning and Filter Removal ........
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION attics, crawl spaces or garages. OPERATION and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.
- Page 6 MODELS: MH70230AS, MH70236AS, MH70248AS PARTS SUPPLIED 1 - Hood pre-installed 1 - 10” round transition adapter 1 - Top Ducting Cover Plate 1 - Hardware package HARDWARE PACKAGE CONTENTS Light Bulb Removal M6 x 2” (4) Suction Cup (1) M6 x 1-1/2” (4) M6 x 1”...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3-1/ 4” x 10” 1 Ft. 6” Round 30 Ft. Rect., wall cap straight with damper 6” Round, 1 Ft. 6” Round, 30 Ft.
- Page 8 Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than 12" 36”. It is important to install the hood at the proper mounting height. Hoods mounted too low could 18"...
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Some Ducting Options Roof Pitch w/ Flashing & Cap Side wall cap w/ gravity damper Soffit or crawl space...
- Page 10 Top View Side View 2 3/4” 14 3/16” 10 3/8” 1 3/4” 4 5/16” 6” 8 9/16” 12” 10 3/8” 18” 1 1/16” 11 9/16” 4” 9 15/16” 24” 29 7/8” (30”) 35 7/8” (36”) 47 7/8” (48”) Back View Back View Ducting &...
- Page 11 ELECTRICAL WARNING how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electrical Supply: This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
- Page 12 CAUTION: At least two installers are required due to the weight and size of the hood. prepare hood. Refer to page 11 for dual blower horizontal ducting. 4” wood board 2. Plum and mark center line. 3. Choose desired height above cooking surface (26” min). Level and ”...
- Page 13 1. Disconnect both blower plugs. to top of interior body of hood. Remove dual blower from hood body. 3. Remove knock out plate A from back of hood 4. Position dual blower at back of hood. Tuck dual blower plate under blower clips and secure mallet.
- Page 14 1 Blower On/Off/Speed Selection 2 Lights Dim/Bright/Off 1 Blower On/Off/Speed Selection Rotate dial to change speed levels, (1) for low speed, (2) for medium speed and (3) for high speed 2 Lights Dim/Bright/Off Rotate dial to change light settings, (1) for dim light and (2) for bright light...
- Page 15 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless should never need replacing, they are required to be cleaned every 30 days or more often depending on cooking habits.
- Page 16 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
- Page 17 TROUBLESHOOTING PROCEDURES FOR MH702 Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 18 MH70230AS MH70236AS MH70248AS...
- Page 19 DESCRIPTION PART # Replacement Parts Optional Accessories To order parts, please call us at 1.888.750.1698...
- Page 20 STAPLE YOUR RECEIPT HERE Proof of the original purchase Limited Warranty date is needed to obtain service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-750-1698 Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...