Related Manuals for MSTRONIC MSE PSE-SW3G
Summary of Contents for MSTRONIC MSE PSE-SW3G
- Page 1 MSE PSE-SW3G 3 Port PoE Switch & Extender (Repeat Ethernet and PoE) USER’S MANUAL MSTRONIC CO., LTD.
-
Page 2: Table Of Contents
User’s Manual MSE PSE-SW3G series 1. General Information.............. 2. Hardware Description............LED Indicators..................Power Wiring ..................Ethernet Port Wiring................PD Port Wiring..................Network Application……………………………………......3. Model Information............4. Technical Specification............MSTRONIC CO., LTD. -
Page 3: General Information
User’s Manual MSE PSE-SW3G series 1. General Information The PoE (Power Over Ethernet) Switch family provide two 10M/100M/1000M TX ports with PoE PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It allow powered from PoE power souring equipment (PSE) and deliver power to PoE powered device (PD), which is compliant with IEEE802.3af and IEEE802.3at standard to receiver and deliver both of Ethernet data... - Page 4 User’s Manual MSE PSE-SW3G series *POWER LED STATUS Description Power Green LED ON when power input (DC IN on rear panel or Port UPLINK on front panel) has valid power supplied. The indicator only been used on PSE-SW3G11CN, LED ON when the following warning condition happened.
-
Page 5: Power Wiring
User’s Manual MSE PSE-SW3G series *PoE LED (the left indicator on RJ45) P1~P2 Yellow A valid Powered Device (PD) is detected and delivering power on this port. No PD is detected on this port. Yellow Powered via all 4 data pairs. - Page 6 User’s Manual MSE PSE-SW3G series The port 3 may get DC power over the Ethernet cable, the connection as: * Data pair A plus V+ /V- on line 1 and 2 * Data pair B plus V-/V+ on line 3 and 6...
- Page 7 User’s Manual MSE PSE-SW3G series Input Voltage Input Voltage Model Output voltage 802.3af/at Isolated (REAR) (Port 3) 10-57VDC 10-57VDC No input (As input voltage) (non-regulated) 42.5-57VDC PSE-SW3G11CN No input 42.5-57VDC (non-regulated) Higher voltage 10-57VDC 42.5-57VDC output (REAR or Port 3)
-
Page 8: Ethernet Port Wiring
User’s Manual MSE PSE-SW3G series *Ethernet Port Wiring The PoE switch family supports one RJ-45 uplink (port 3 with PoE PD) and two RJ-45 ports (port 1&2 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense the speed and duplex for 10Base-T, 100Base-TX or 1000Base-T connection. - Page 9 User’s Manual MSE PSE-SW3G series Cross-over Cabling Pin 1 Pin 3 Pin 2 Pin 6 Pin 3 Pin 1 Pin 6 Pin 2 Pin 4 Pin 7 Pin 5 Pin 8 Pin 7 Pin 4 Pin 8 Pin 8 Connect an Ethernet cable into any switch port and connect the other side to your attached device.
-
Page 10: Pd Port Wiring
User’s Manual MSE PSE-SW3G series *PD Port Wiring Port 1 & 2 provide PoE inject function with maximum 35W ability to power up the powered device use the straight-through or cross-over Ethernet cable. The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following table shows pin assignment of alternative A and B for the Power Source Equipment. -
Page 11: Network Application
User’s Manual MSE PSE-SW3G series *Network Application The PoE Switch can receive power from PoE midspan and provide power to the PD which follows the IEEE 802.3af/at standard in the network. The PoE Switch can be installed in a more appropriate position for better performance to extend Ethernet to 200 meters. -
Page 12: Model Information
User’s Manual MSE PSE-SW3G series 3. Model Information Input Voltage Input Voltage Model Output voltage 802.3af/at Isolated (REAR) (Port 3) 10-57VDC PSE-SW3G11CN 10-57VDC 42.5-57VDC (non-regulated) 40-57VDC PSE-SW3G44DN 40-57VDC 42.5-57VDC (non-regulated) *Suffix L for DIN RAIL Mounted AC/DC Adapter (Option) MS-A150-18-1... -
Page 13: Technical Specification
User’s Manual MSE PSE-SW3G series 4. Technical Specifications Standards IEEE802.3/IEEE802.3u standards/IEEE802.3ab (10 base-T/100base-TX/1000base-T) Ports 3 ports with PoE (2 PSE & 1 PD), support auto-crossover & auto-polarity Transmission speed 1000Mbps (1000base-T).100 Mbps (100base-TX), 10 Mbps(10base-T) Auto-negotiation Switch technology store-and-forward Protocols... - Page 14 User’s Manual MSE PSE-SW3G series PoE auto detection IEEE802.3af & IEEE802.3at (2 event classification signaling) PoE protection Over-temperature, over-current, over/under voltage LEDs *Link/Activity (Green ON/ Green Blinking @1000Mbps, Yellow/Yellow Blinking @10M/100Mbps) *PoE (Yellow) port 1&2 ON - PD detect Port 3 ON – 4 pair power, Blinking-2 pair power...
Need help?
Do you have a question about the MSE PSE-SW3G and is the answer not in the manual?
Questions and answers