Related Manuals for Securitytec DVR8MP4
Summary of Contents for Securitytec DVR8MP4
- Page 1 Thank you for purchasing our product. Please read this User’s Manual before using the product. Change without Notice 8/16 Channel MPEG4 Digital Video Recorder User’s Manual for model numbers: DVR8MP4 DVR16MP4...
- Page 2 SPECIFICATION Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be sufficient magnitude to constitute risk of electrical shock to persons.
- Page 3 SPECIFICATION About this document Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users Manual. Pay particular attention to the parts that are marked NOTICE. Also, when connecting with external application, first turn the power OFF and follow manual instruction for appropriate installation.
- Page 4 SPECIFICATION FCC Statement: WARNING This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation." * Federal Communications Commission (FCC) Statement WARNING This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to...
- Page 5 SPECIFICATION Unit Description of Front Panel MT / PST: Multi screen select / PTZ preset function. PTZ: PTZ control mode. FUNC: System information. AUTO : Channel auto sequence. PIP: main and sub screen mode 1 ~ 16 full screen FREEZE / MENU / ESC/SPOT ZOOM / BACKUP / T-SRH Playback / Record Value change button...
- Page 6 SPECIFICATION Unit Description of Rear Panel REAL PANEL COMMENTARY ABOUT A.C. POWER SWITCH Before operation, please verify the working voltage to be 110 or 220 VAC. Adjust the power switcher at the rear panel to the correct location. Activate the power switch to on and you are ready for operation. Power cord in 12V/5A, power switcher (ON / OFF) 75 Ohm ON/OFF Camera 1 ~ 16 in and...
-
Page 7: Device Controls
SPECIFICATION DEVICE CONTROLS 1) Camera Connection Connect camera to the CAMERA INPUT located at rear side of the DVR. 2) Monitor Connection (Composite Connection Method) Connect monitor to the MONITOR output located at rear side of the DVR. 3) Alarm in and Relay out Relay output : COM+NC, COM+NO Alarm input : Short-circuit between Alarm1 ~ 16 and GND is recognized as alarm by default. -
Page 8: Power On/Off
SPECIFICATION POWER ON /OFF After the connection of power cord and other devices with this DVR, turn the power on. a. The video signal system (NTSC or PAL) is automatically detected. b. Power Failure Recovery. This DVR automatically reverts back to programmed record parameters upon power restoration. -
Page 9: Multi Screen Mode
SPECIFICATION Auto Sequence Display <ADD AUTO SINGLE: ON> - Press the AUTO button, each screen display will be automatically switching according to the AUTO SEQUENCE setup. - If you set up “ADD AUTO SINGLE: OFF” in the AUTO SEQUENCE setup menu, the single display will be skipped. -
Page 10: Manual Mode
SPECIFICATION RECORD TYPE SELECTION Press the REC button and the following message will be displayed as below; MANUAL MODE Press the REC button to begin recording. To stop recording, press the STOP button again. SCHEDULE MODE When Schedule mode is selected, the recording will be automatically executed according to the recording schedule. -
Page 11: Calendar Search
SPECIFICATION DATA SEARCH & PLAYBACK Press the T-SRH (Time - search) button, the SEARCH menu screen appears. TIME SEARCH If you press the PLAY button in the real time screen mode, playback will be executed from the end of the previous time search and press the desired channel select button. -
Page 12: Search & Copy
SPECIFICATION SEARCH & COPY At the SEARCH menu; Move the cursor to TIME SEARCH using button. Press the ENTER button and TIME SEARCH screen appears. Select the desired HDD ID using the (-) or (+) button. Move the cursor to CHANNEL using the button and select the desired channel using the (-) or (+) button. - Page 13 SPECIFICATION Select the desired HDD ID using the (-) or (+) button. Move the cursor to CHANNEL using the button and select the desired channel using the (-) or (+) button. Move the cursor to the desired position of SEARCH TIME using the buttons, and then set up the desired time using the(-), (+) buttons or turn the JOG DIAL to set the search time.
- Page 14 SPECIFICATION BLOCK SEARCH At the SEARCH menu; Move the cursor to BLOCK SEARCH using button. Press the ENTER button and the BLOCK SEARCH menu screen appears. Select the desired HDD ID using the (-) or (+) button. Move the cursor to the desired position of SEARCH TIME using the buttons, and then set up the desired time using the(-), (+) buttons.
-
Page 15: Bookmark Search
SPECIFICATION FILE SEARCH At the SEARCH menu; Move the cursor to FILE SEARCH using button. Press the ENTER button and the FILE SEARCH screen appears. Select the desired type of MEDIA using the (-) or (+) button. Press the ENTER button or turn the JOG DIAL, and the list searched appears. When the list appears on the screen, select the desired list using buttons or JOG DIAL. -
Page 16: Log File Search
SPECIFICATION LOG FILE SEARCH At the SEARCH menu; Move the cursor to LOG FILE SEARCH using button. Press the ENTER button and the LOG FILE SEARCH screen appears. Move the cursor to the desired position of SEARCH TIME using the buttons, and then set up the desired time using the(-), (+) buttons. - Page 17 SPECIFICATION <How to release the section repetition playback> Press the “PAUSE” button. Press the “AUTO” button and then press the “FREEZE” button to exit the section repetition playback mode. FAST ( Press this button to make faster the speed level which is higher than normal speed (X1) and displayed at the upper left side of screen as below: 2 - 2 times faster than normal playback speed 4 - 4 times faster than normal playback speed...
-
Page 18: Digital Zoom
SPECIFICATION DIGITAL ZOOM Press the desired camera number button you wish to display on the monitor. Press the D-ZOOM button. The indication screen appears on the main screen. Turn JOG DIAL or press the buttons to select the desired location. Press the ENTER button to change the zoom x2 ~ x4. -
Page 19: Copy To Hdd
SPECIFICATION COPY Press the COPY button to copy the recorded images into other media and the COPY MENU screen appears. COPY TO HDD At the COPY menu, Move the cursor to COPY using the buttons. Press the ENTER button and the following screen appears. Select the desired MEDIA(HDD) (-), (+) buttons or jog dial. - Page 20 SPECIFICATION COPY TO USB memory stick At the COPY menu, Move the cursor to COPY using the buttons. Press the ENTER button and the following screen appears. Select the desired MEDIA(USB) (-), (+) buttons or jog dial. Move the cursor to HDD ID using the buttons and select the desired HDD to copy among HDD IDs using the (-), (+) buttons or jog dial.
- Page 21 SPECIFICATION Select the desired MEDIA(CD-RW/DVD±RW) (-), (+) buttons or jog dial. Move the cursor to HDD ID using the buttons and select the desired HDD to copy among HDD IDs using the (-), (+) buttons or jog dial. Move the cursor to the desired position of COPY START TIME/ COPY END TIME using buttons and press the (-) or (+) button to set up the time or turn the JOG DIAL to set up the COPY START TIME and COPY END TIME.
-
Page 22: Media Format
SPECIFICATION COPY STATUS At the COPY menu, Move the cursor to COPY STATUS using the buttons. Press the ENTER button to see the current copying status and the following screen appears. Press the ESC button to exit this menu. CUR TIME : Indicate current copying situation among the total copying data. MEDIA FORMAT At the COPY menu, Move the cursor to MEDIA FORMAT using the... -
Page 23: Dvr Status
SPECIFICATION DVR STATUS Press the “ENTER” button or double-click the left button of Mouse, The SYSTEM INFOMATION screen will appear. To see the next page, press the or use the wheel scroll of Mouse. Press the STATUS button again to move on next information screen or press the “ESC” button to exit the menu. -
Page 24: Quick Setup
SPECIFICATION MENU setup Press the MENU button for the desired DVR setting. You can use the mouse instead of buttons on the front panel of DVR. Simply click the desired icon or item in case of using the mouse. QUICK SETUP Press the MENU button and the QUICK SETUP menu appears as the following picture. -
Page 25: Pre Record Time
SPECIFICATION EVENT Select a kind of EVENT using the (-), (+) buttons or jog dial. If you want to select all kind of event, choose “ALL” and if you don’t want event recording, choose “OFF”. The default is “ALL”. PRE RECORD TIME Select the desired time for pre-recording using the (-), (+) buttons or jog dial. - Page 26 SPECIFICATION POSITION At the SCREEN menu, Press the ENTER button when the cursor is on the POSITION and the following items appear. Change the value of the HORIZONTAL POSITION using the (-), (+) buttons or jog dial to adjust the horizontal position of the screen.
-
Page 27: Auto Sequence
SPECIFICATION AUTO SEQUENCE At the SCREEN menu, Move the cursor to the AUTO SEQUENCE using buttons. Press the ENTER button when the cursor is on the AUTO SEQUENCE and the following 3 pages screen appears. Move the cursor to each single or split channel using the buttons. -
Page 28: Hdd Free Space Mode
SPECIFICATION DISPLAY At the SCREEN menu, Move the cursor to the DISPLAY using buttons. Press the ENTER button when the cursor is on the DISPLAY and the following items appear. To exit this DISPLAY menu, press the ESC button. HDD FREE SPACE At the DISPLAY menu, Move the cursor using the buttons to select the HDD FREE SPACE. - Page 29 SPECIFICATION CLOCK DISPLAY At the DISPLAY menu, Move the cursor using the buttons to select the CLOCK DISPLAY. Use the (-), (+) buttons or jog dial to choose “ON” or “OFF”. * The default is “ON”. ON: The date and time will be displayed on the screen. DATE&TIME MODE At the DISPLAY menu, Move the cursor using the...
-
Page 30: Spot Display
SPECIFICATION REMOTE CONTROL ID At the DISPLAY menu, Move the cursor using the buttons to select the REMOTE CONTROL ID. Use the (-), (+) buttons or jog dial to choose “ON” or “OFF”. The default is “OFF”. ON: The remote controller ID will be displayed on the screen. SPOT DISPLAY At the DISPLAY menu, Move the cursor using the... - Page 31 SPECIFICATION Press the ENTER button after selecting desired channel using the buttons and the following screen appears. Select the character using the buttons and then press the ENTER button. To exit this CHARACTER TABLE screen, press the ESC button. CHANNEL TITLE MODE: There are “TEXT” and “BITMAP”. TEXT: Using the CHARACTER TABLE BITMAP: It is possible to download new characters using the software if you want.
- Page 32 SPECIFICATION LIVE 4E / LIVE 9B Press the ENTER button after selecting “LIVE 4E” or “LIVE 9B” using the buttons. [LIVE4E] [LIVE9B] Set the desired number of camera in each channel screen using the (-), (+) buttons or jog dial. Use the buttons to set the other channel screen.
-
Page 33: Spot Mode
SPECIFICATION SPOT At the SCREEN menu, Move the cursor to the SPOT using buttons. Press the ENTER button when the cursor is on the SPOT and the following screen appears. To exit this SPOT menu, press the ESC button. SPOT MODE Use the (-), (+) buttons or jog dial to select the SPOT MODE. -
Page 34: Record Setup
SPECIFICATION RECORD To set up the RECORD menu, Move the cursor to the RECORD icon using the in the MENU screen. Press the ENTER button when the cursor is on the RECORD icon and the following items appear. RECORD SETUP At the RECORD menu, Move the cursor to the RECORD SETUP using buttons. -
Page 35: Record Program
SPECIFICATION RECORD PROGRAM At the RECORD menu, Move the cursor to the RECORD PROGRAM using buttons. Press the ENTER button when the cursor is on the RECORD PROGRAM and the following screen appears. Use the buttons to move the cursor to the desired item. Select the desired RECORD TYPE using the (-), (+) buttons or jog dial. - Page 36 SPECIFICATION < Result table of total frame rate > Record Image Size Normal Record Event Record Unit Type Event Channel Other Channel Single 360 x 240 Normal Frame ES_Frame RS_Frame CIF/1 SEC 720 x 240 Normal Frame ES_Frame RS_Frame CIF/1 SEC 720 x 480 Normal Frame ES_Frame...
-
Page 37: Specification
SPECIFICATION < PROGRAM DEFAULT> PROGRAM RECORD COMPLEX SINGLE SINGLE COMPLEX SINGLE SINGLE COMPLEX SINGLE SINGLE COMPLEX TYPE RECORDING INTERVAL 704x576 IMAGE 704x288 352x288 352x288 360x240 704x288 704x288 704x288 704x576 704x576 704x576 SIZE 352x288 NORMAL EVENT SINGLE EVENT COMPLEX QUALITY NORMAL QUALITY EVENT PRE-ALARM... -
Page 38: Audio Record
SPECIFICATION IMAGE QUALITY At the RECORD menu, Move the cursor to the IMAGE QUALITY using buttons. Press the ENTER button when the cursor is on the IMAGE QUALITY and the following screen appears. Select the desired RECORD QUALITY using the (-), (+) buttons or jog dial. And you can see the size of each image quality and how long you can record in the installed HDDs by the image quality. -
Page 39: Repeat Record
SPECIFICATION REPEAT RECORD At the RECORD menu, Move the cursor to the REPEAT RECORD using buttons. Press the ENTER button when the cursor is on the REPEAT RECORD and the following screen appears. Use the (-), (+) buttons or jog dial to set “ON” or “OFF”. It is possible to set a point of time to work the REPEAT RECORD ALARM. -
Page 40: Motion Detection
SPECIFICATION HOLIDAY At the RECORD menu, Move the cursor to the “HOLIDAY” using buttons. Press the “ENTER” button to set up “HOLIDAY” and the HOLIDAY menu screen appears. Set up “ON” or “OFF” of HOLIDAY RECORD using the (-), (+) buttons or jog dial. Move the cursor using buttons and set up the value using the (-), (+) buttons or jog dial. -
Page 41: Area Setup
SPECIFICATION At the EVENT menu, Move the cursor to the MOTION DETECTION using buttons. Press the ENTER button when the cursor is on the MOTION DETECTION and the following screen appears. CHANNEL At the MOTION DETECTION menu, ○ Move the cursor to CHANNEL using buttons. -
Page 42: Event Screen Mode
SPECIFICATION TEST MOTION At the MOTION DETECTION menu, Move the cursor to TEST MOTION using the buttons. Press the ENTER button to test the motion detection. To exit this TEST MOTION, press the ESC button. EVENT SCREEN MODE At the EVENT menu, Move the cursor to the EVENT SCREEN MODE using buttons. -
Page 43: Sensor Input
SPECIFICATION SENSOR INPUT At the EVENT menu, Move the cursor to the SENSOR INPUT using the buttons. Press the ENTER button when the cursor is on the SENSOR INPUT and the following 2 pages screen appears Select the desired channel using the buttons. - Page 44 SPECIFICATION Move the cursor using the buttons and set up the value using the (-), (+) buttons or jog dial. Press the button to see the next page. To exit this screen, press the “ESC” button. NOTE - It is possible to set the RELAY OUTPUT of each channel in the type of event. - Relay output is from 1 to 4 and it is possible to set the period of the relay output.
- Page 45 SPECIFICATION HDD CONFIGURATION At the HDD menu, Move the cursor to HDD CONFIGURATION using the buttons. Press the ENTER button when the cursor is on the HDD CONFIGURATION and the following screen appears. Use the buttons to move the cursor and use the (-), (+) buttons or jog dial to change the value.
-
Page 46: Backup Hdd Initialize
SPECIFICATION BACKUP HDD INITIALIZE At the HDD menu, Move the cursor to “BACKUP HDD INITIALIZE” using the buttons. Press the “ENTER” button when the cursor is on the “BACKUP HDD INITIALIZE” and the following screen appears. If you want to initialize, move the cursor to “YES” and then press the ENTER button. If not, move the cursor to “NO”... -
Page 47: Date And Time
SPECIFICATION CLOCK At the SYSTEM menu, Move the cursor to the CLOCK using the buttons. Press the ENTER button when the cursor is on the CLOCK and the following screen appears. DATE&TIME At the CLOCK menu, Move the cursor to the DATE&TIME using the buttons. -
Page 48: Master Password
SPECIFICATION PASSWORD At the SYSTEM menu, Move the cursor to the PASSWORD using the buttons. Press the ENTER button when the cursor is on the PASSWORD and the following screen appears. To exit this PASSWORD menu, press the ESC button. MASTER PASSWORD At the PASSWORD menu, Move the cursor to the MASTER PASSWORD using the... -
Page 49: Supervisor Password
SPECIFICATION SUPERVISOR PASSWORD At the PASSWORD menu, Move the cursor to the SUPERVISOR PASSWORD using the buttons. Press the ENTER button when the cursor is on the SUPERVISOR PASSWORD and the following screen appears. Insert the current password in the eight digits marked ******** beside OLD PASSWORD using the CAMERA/ NUMBER INPUT buttons. -
Page 50: Rec/Play Check
SPECIFICATION REC/PLAY CHECK At the PASSWORD menu, Move the cursor to the REC/PLAY CHECK using the buttons. Select “ON” or “OFF” to set up the REC/PLAY CHECK using the (-), (+) buttons or jog dial. If REC/PLAY CHECK is “ON”, the password will be required when you start to record or playback. The default is “OFF”. -
Page 51: Dvr Initialize
SPECIFICATION DVR INITIALIZE At the SYSTEM menu, Move the cursor to the DVR INITIALIZE using the buttons. Press the ENTER button when the cursor is on the DVR INITIALIZE and the following screen appears. If you want to initialize, move the cursor to “YES” and then press the ENTER button. If not, move the cursor to “NO”... -
Page 52: Firmware Update
SPECIFICATION FIRMWARE UPDATE At the SYSTEM menu, Move the cursor to the FIRMWARE UPGRADE using the buttons. Press the ENTER button when the cursor is on the FIRMWARE UPDATE and the following screen appears. If you want to update firmware using the USB port, move the cursor to “YES” and then press the ENTER button. -
Page 53: Subnet Mask
SPECIFICATION NETWORK At the LINK menu, Move the cursor to the NETWORK using the buttons. Press the ENTER button when the cursor is on the NETWORK and the following screen appears. To exit this NETWORK menu, press the ESC button. <Fixed IP>... - Page 54 SPECIFICATION At the NETWORK menu, Move the cursor to the DNS using the buttons. Select the desired position using the buttons and set the data value using the (-), (+) buttons or jog dial. PORT At the NETWORK menu, Move the cursor to the PORT using the buttons.
- Page 55 SPECIFICATION RS 232C At the LINK menu, Move the cursor to the RS232 using the buttons. Press the ENTER button when the cursor is on the RS232 and the following screen appears. Use the buttons to choose the item and use the (-), (+) buttons or jog dial to set the data value. To exit this RS232 menu, press the ESC button.
- Page 56 SPECIFICATION At the SCREEN menu, Move the cursor to the PTZ using buttons. Press the ENTER button when the cursor is on the PTZ and the following 2 pages screen appears. Select the desired channel using buttons. Use the (-), (+) buttons or jog dial to select the right model of installed PTZ camera. Press the button to set up a ID of the PTZ camera.
- Page 57 SPECIFICATION PTZ PRESETTING Press the “PTZ” button to enter PTZ mode. Press the “PRESET” button to enter PRESET mode and “PTZ(PRESET)MOVE”, OSD will be displayed on the left side of the monitor. KEY_MENU: open PTZ MENU KEY_PRESET: Preset function key KEY_ESC: clear preset point KEY_FREEZE: call preset point KEY_AUTO: Auto Pan...
- Page 58 SPECIFICATION SEARCH To set up the SEARCH menu, Move the cursor to the SEARCH icon using the in the MENU screen. Press the ENTER button when the cursor is on the SEARCH icon and the following items appear. COPY Press the COPY button to copy the recorded images into other media and the COPY MENU screen appears. To set up the COPY menu, Move the cursor to the COPY icon using the in the MENU screen.
-
Page 59: Copy Status
SPECIFICATION COPY STATUS At the COPY menu, Move the cursor to COPY STATUS using the buttons. Press the ENTER button to see the current copying status and the following screen appears. MEDIA FORMAT At the COPY menu, Move the cursor to MEDIA FORMAT using the buttons. - Page 60 SPECIFICATION EXIT At the MENU screen, Move the cursor to the EXIT icon using the buttons. Press the ENTER button when the cursor is on the EXIT icon and the following items appear. Move the cursor to the desired item using the buttons and press the ENTER button.
-
Page 61: Recording Conditions
SPECIFICATION < Recording Time Table > 1. RECORDING CONDITIONS Based on 120GB of storage with the installation of 1 camera. This DVR can support up to 22TB with external HDD storage devices.. 2. RECORDING TIME TABLE VIDEO RECORD IMAGE IMAGE 120fps(CIF) 60fps(CIF) 30fps(CIF) -
Page 62: Network Viewer Installation
NETWORK VIEWER INSTALLATION Network Viewer Installation of Network Viewer Software System requirement - Pentium III or above recommended - O/S : Microsoft Windows 2000 / XP - 128MB RAM or above recommended - Super VGA 16M or above recommended - 10/100 base T network card for LAN operation Network Environment Client PC Minimum... -
Page 63: Add A New Site Information
NETWORK VIEWER INSTALLATION Add a new site information ○ Click the “Select a DVR” button to display the DVR List on the screen. ○ Fill out Type, DVR Name, IP address and Password to add the desired units into the DVR information box, and then click on the “Add”... -
Page 64: Dvr Search
NETWORK VIEWER INSTALLATION DVR search This menu allows you to detect all the units on the local network. Search DVR ○ Click “Search DVR” button to display the “Search” menu window. ○ Click the “Search” button, and then all the units on the local network will be detected and listed on the screen. -
Page 65: File Search
NETWORK VIEWER INSTALLATION File Search At the above main menu controller, ○ Click the “File Search” button and the “File list” window will appear on the PC screen. If you want to search images saved in CD-RW, DVD±RW or PC, insert the CD or DVD into your ○... - Page 66 NETWORK VIEWER INSTALLATION At the above main menu controller, ○ Click the “Arrange” button when you access more than one DVR and the windows are arranged in a grid on your PC screen. * 1 site windows * 2 ~ 4 site windows *5 ~ 9 site windows *10~16 site windows NOTE - You can connect up to 16 DVRs with your PC simultaneously.
-
Page 67: Screen Display
NETWORK VIEWER INSTALLATION Option ® Insert the CD into the CD-ROM drive, and then please double-click the icon of Viewer and the following main menu controller will appear on the PC screen. Option ○ Click the “Option” button to change the other MENU setups. ○... - Page 68 NETWORK VIEWER INSTALLATION Multi-screen display ○ Click the “MULTI” button and the multi-screen will be displayed. ○ Click the “MULTI” button again to view other multi-screen. NOTE Selecting a Multi-display may slow down the updates as multiple connections are made to the DVR at the same time.
- Page 69 NETWORK VIEWER INSTALLATION This menu allows you to control the PTZ camera through the network. ○ Click the “PTZ” button to display the following PTZ controller. ○ Click the button to tilt up or down. ○ Click the button to pan left or right. ○...
- Page 70 NETWORK VIEWER INSTALLATION SETUP You can modify DVR MENU setup through the network. ○ Click the “SETUP” button on the control menu bar to display the DVR setup screen after connecting the view screen. (It is possible only for master connection.) ○...
- Page 71 NETWORK VIEWER INSTALLATION STATUS ○ Click the “STATUS” button on the control menu bar to display the DVR status after connecting the view screen. PRINT After connecting the view screen, ○ Click the “PRINT” button on the control menu bar to print the desired image. And the preview window will be displayed as the above picture.
-
Page 72: Audio Out
NETWORK VIEWER INSTALLATION COPY After connecting the view screen, ○ Click the “COPY” button on the control menu bar to copy the desired image. ○ The Copy control window will appear. ○ Click the “Copy” button of the control window after setting the desired HDD and the time. AUDIO IN After connecting the view screen, ○... -
Page 73: Time Search
NETWORK VIEWER INSTALLATION TIME SEARCH : You can search and playback the images by the time. After connecting the view screen, Click the “TIME” button on the control menu bar to display the Time Search window. ○ ○ Select the desired HDD mode in the HDD dropdown list, and then click the “Search” button. ○... -
Page 74: Block Search
NETWORK VIEWER INSTALLATION BLOCK SEARCH : You can search and playback the images by the block. After connecting the view screen, ○ Click the “BLOCK” button on the control menu bar to display the Block Search window. ○ Select the desired HDD mode and set the Search Time, and then click the “Search” button. ○... -
Page 75: Key Information
NETWORK VIEWER INSTALLATION Key Information PAUSE ○ Click this button to pause the images during the playback or live. PLAY (Reverse & Forward) ○ Use these buttons to playback images at normal speed in either direction. FAST (Reverse & Forward) ○... - Page 76 NETWORK VIEWER INSTALLATION Notice: DDNS function support update. ENTER Select DDNS mode ON.
- Page 77 NETWORK VIEWER INSTALLATION Insert Host name, User name and password with character table. Net viewer DDNS mode:...
- Page 78 NETWORK VIEWER INSTALLATION Type in DDNS host name, and then add to list. Host name is the priority if there is an IP address is still fill in. Host name should be left blank if IP address is used. DDNS Host name HDD is readable in PC with netveiwer, Please select NTSC or PAL mode if the video system format displays different to your...
- Page 79 NETWORK VIEWER INSTALLATION...