Related Manuals for Securitytec SW-11Z-I1-V1
Summary of Contents for Securitytec SW-11Z-I1-V1
- Page 1 User Manual SW-11Z-I1-V1.0-E ─ DVR ─ This document contains preliminary information and subject to change without notice.
- Page 2 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE: This equipment has been tested and found to comply with the limits for a class digital device, pursuant to part 15 of the FCC Rules.
-
Page 3: Table Of Contents
Table of Contents CHAPTER 1 MAIN MENU SETUP ____________________________________ 4 1-1 RECORD SETUP ____________________________________________ 5 1-1.1 Quality & Frame Rate Setup _____________________________ 6 1-2 EVENT SETUP ______________________________________________ 6 1-2.1 MOTION SETUP ________________________________________ 7 1-2.1.1 MOTION AREA SETUP______________________________ 7 1-2.2 SENSOR SETUP ________________________________________ 8 1-3 SCHEDULE SETUP __________________________________________ 9 1-3.1 Schedule Record Setup _________________________________ 9 1-3.2 Holiday Setup _________________________________________ 10... -
Page 4: Chapter 1 Main Menu Setup
CHAPTER 1 MAIN MENU SETUP To enter the main menu and set up DVR, log-in account and user password are required. The default password of the administrator is “123456”. Please check the “Account Setup” for related setup of other log-in users. Table 1-0.1 Some definition of virtual keyboard. -
Page 5: Record Setup
Table 1-0.2 The operation of remote control under the setting menu Item Description Switch to different options under one item Switch to different items MENU Save setup and back to LIVE mode Back to Upper level of menu without saving ENTER Enter the menu, or display virtual keyboard PS. -
Page 6: 1-1.1 Quality & Frame Rate Setup
1-1.1 Quality & Frame Rate Setup Item Description Normal setup/ Select recording mode event setup Select recording resolution: NTSC:352x240, 704x240, 704x480 Resolution PAL:352X288,704X288,704X576 Record Type You can setup quality and FPS separately for record type. Check/uncheck the box enable/disable selected channel recording Quality Select quality: Below Basic/ Basic/ Normal/ High/ Highest Select recording frame rate. -
Page 7: 1-2.1 Motion Setup
1-2.1 MOTION SETUP Item Description When motion detect，the number of seconds continuous alarm Alarm Duration(Seconds) 1~16 You can setup independently for each channel. Enable Check the box to Enable/Disable motion detection for each channel. Drag the white bar or press ◀ ▶ to set up Sensitivity from Sensitivity value 0 to 10 for each channel. -
Page 8: 1-2.2 Sensor Setup
Item Description Switch between “select” and “deselect” for cursor-dragging function Mask Mouse Selection All Area Detection Select entire screen as detection area. Mask All Area Deselect entire detection area. Continue Continue setup Exit & Save Save setup and leave Exit & Discard Cancel setup and leave 1-2.2 SENSOR SETUP Item... -
Page 9: Schedule Setup
1-3 SCHEDULE SETUP Except from starting recording manually, you can also setup the recording time by weeks and schedule including normal, motion detect, and recording type. Item Description Page Each page provides 10 schedules for setup. 5 pages in total. Holiday Setup Enter to setup holiday, up to 50 days, other than weekends,. -
Page 10: 1-3.2 Holiday Setup
1-3.2 Holiday Setup Since holidays are different by different country and region, you can setup the holiday of your location accordingly. 1-4 CAMERA SETUP Item Description 1~16 You can setup independently for each channel. Mask Check the box to Enable/Disable mask function for LIVE mode Drag the bar or press ◀... -
Page 11: Account Setup
1-5 ACCOUNT SETUP The Account Setup menu is used to provide role-based permission independently setting for each user (maximum of 4 users) to access DVR over network. The default admin account and password is “admin” and “123456” (The default password remains the same after firmware upgrade) Item Description Check to activate the user’s account. -
Page 12: 1-5.2 User Picture Setup
1-5.2 User Picture Setup User can select picture wished to be changed to from hard drive. 1-6 NETWORKING SETUP Item Description Connect type Setup mode for network connection: (ADSL、DHCP、LAN、3G). HTTP Setup Enter to set up HTTP DDNS Setup Enter to set up DDNS Mail Setup Enter to set up mail 3G Setup... -
Page 13: 1-6.1 Networking Setup
1-6.1 NETWORKING SETUP There are three ways to connect to the network as followed. 1-6.1.1 DHCP When DHCP is selected, IP address will be assigned by DHCP server automatically. 1-6.1.2 LAN Select LAN for network connection, the following information is required. Item Description IP Address... -
Page 14: 1-6.1.3 Adsl
1-6.1.3 ADSL Select ADSL for network connection, the following information is required. Item Description User Name Enter user name provided by ISP Password Enter password provided by ISP 1-6.1.4 3G Select 3G for network connection, the following information is required. Item Description Dial-up Number... -
Page 15: 1-6.2 Http Setup
Item Description Enable Enable advance setting User Name Enter ISP username Password Enter ISP password IP Address Enter the ISP provides a fixed IP address。 (if the client uses the Internet only need to enter a fixed IP) PS：This feature currently only supports the Huawei 3G card 1-6.2 HTTP Setup Item Description... -
Page 16: 1-6.3 Ddns Setup
1-6.3 DDNS Setup Item Description Enable DDNS Enable/disable DDNS function. Enter the registered SMTP Server: DDNS Server 、 、 DYNDNS.ORG 、 NO-IP.ORG 、 3322.ORG ez-dns＊ I-DVR.NET＊ Host Name Enter the completed registered SMTP Server. (Including username + Server) If the user name is h.264 and you choose i-dvr as your server, you should enter: h.264.i-dvr.net User Name... -
Page 17: 1-6.4 Mail Setup
1-6.4 Mail Setup When event occurs (VLOSS, MOTION), email will be sent to the receiver account automatically. Item Description Enable E-mail Notification Check the box to enable/disable E-mal Notification function. Enter to set up SMTP Server name. SMTP Server (Varies according to the user) User Name Enter to set up User Name. -
Page 18: Ptz & Rs485 Setup
1-7 PTZ & RS485 SETUP The DVR allows users to control PTZ functions of your camera. To enable PTZ function, the 485 cable should be connected to the RS-485 port of DVR. Item Description Enable PTZ Click the box to Enable/Disable PTZ function for each channel. Protocol Set up the protocol of PTZ cam. -
Page 19: System Setup
1-8 SYSTEM SETUP Item Description DVR Name The name of DVR will be shown when users login from remote access. DVR Location The location of DVR will be shown when users login from remote access Click or press ▼ to select OSD language. Language Remote ID Default ID is 0. -
Page 20: 1-8.2 Date/Time Setup
Item Description Auto-Seq Interval Set up duration time in seconds for the interval between channels under Auto-Seq mode. Show OSD Turn On / Off OSD display Show DVR Status Turn On / Off DVR illustration and record status display Show Date/Time Turn On / Off date and time display Show Channel Name Turn On / Off channel name display... -
Page 21: 1-8.2.1 Change Date & Time
1-8.2.1 CHANGE DATE & TIME Setup date and time of DVR manually according to user’s local time. 1-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP Set up time zone and activate Daylight Saving Time function according to user’s DVR location. Item Description Select Time Zone... -
Page 22: 1-8.2.3 Internet Time Setup
1-8.2.3 INTERNET TIME SETUP Synchronize your DVR time with internet time server. Item Description Check to enable DVR automatic synchronization function. Automatic Effective by this option selected, DVR will automatically Synchronization synchronize the time upon rebooting or by every 24 hours after booting. -
Page 23: 1-8.4 Spot Setup
Item Description Key Tone Enable/Disable keystrokes. Enable/Disable buzzer operation when the alarm is triggered for Buzzer sensor, motion and vloss (Video Loss). Enable/Disable the signal to be sent to the RELAY OUT blocks Relay when the alarm is triggered for sensor, motion and vloss. 1-8.4 SPOT SETUP DVR's Main Monitor output signal, do the main screen output or switch SPOT mode output... -
Page 24: Utility Setup
1-9 UTILITY SETUP Item Description Select to enter hard disk initialization menu. Please stop HDD Initialization recording before entering this menu. Enter the menu, system will show all the data (model ,volume ) of HDD that installed in DVR. Check the HDD you’d like to initialize then press “Start”. -
Page 25: Diagnostic
1-10 DIAGNOSTIC Item Description Version The current firmware version of DVR The connected IP address of DVR. If disconnected from network, the screen will display ” NETWORK DISCONNECT”. MAC Address of DVR HDD Status HDD number Volume HDD Capacity Used Rate Percentage of space used on HDD. -
Page 26: Chapter 2 Backup & Search
CHAPTER 2 BACKUP & SEARCH 2-1 BACKUP SETUP User can backup any segment of recorded data in a specified time frame. To do so, either a CD R/W or storage device, like USB, must be connected to the DVR. The format of backup file is IRF file that can be played by both “Ifileplay”... - Page 27 iFileplay Use Method Step 1: install 「iFileplay」 software to your PC. You can get 「 iFileplay」 file from the CD with DVR Packing. PS: When you using USB to backup file, iFileplay.exe will copy to USB with the backup file automatically. Step 2：Setup「ifileplaypack.exe」...
- Page 28 Step 4：Ifileplay software will play the backup file automatically. Step 5：If there is no display on the screen, The backup file is not our DVR recording format. Please check it.
-
Page 29: Search Setup
2-2 SEARCH SETUP Item Description Event Search Event search menu Time Search Enter time search menu 2-2.1 EVENT SEARCH The DVR automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal will be shown on the left side of time information. -
Page 30: 2-2.1.1 Criteria Setup For Event Search
Item Description Criteria Setup conditions of event search Page Switch between pages of events Date/Time Date/time when event occurred. Event type, defined as following MOTION Motion Detected Video Loss Video Loss Remote Login user log-in over the network Remote Logout user log-out over the network Event Type Power On... -
Page 31: 2-2.2 Time Search
2-2.2 TIME SEARCH TIME SEARCH can search for the specific time of recording data to playback. Press “Enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “ “System will start playing back according to the date you selected. -
Page 32: Chapter 3 Remote Software Installation And Setup
CHAPTER 3 Remote Software Installation and Setup 3-1 AP Software Installation and instruction AP software:「DVR Remote Desktop」can allow you to remotely access and control the DVR from PC. p.s. Operation system currently supports Windows XP SP2(above) and Windows Vista, Windows 7 Step One：Enter the IP address of DVR in IE browser Step Two: Windows as below will show up. - Page 33 Step Four: Run or Save our AP software. Step Five: If you choose to run the software, Start window will be shown up. Please enter information of login DVR: IP, Port, Username and Password, or choose “Play Recorded File” to open backup files in your PC. Step Six: You’ve logged into the DVR...
-
Page 34: How To Do Remote Monitoring Through Ie
3-2 How to do remote monitoring through IE Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site DVR. Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456. -
Page 35: How To Do Remote Monitoring Through Jpeg Viewer(Only Monitor Function)
Step Four: DVR images appear. 3-3 How to do remote monitoring through JPEG VIEWER(Only Monitor Fun ction) Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site DVR. Step Two: Windows as below will show up. - Page 36 Step Three: Click on “Jpeg Viewer” Step Four: DVR images appear. PS : Only for viewer, without any operation function.
-
Page 37: Ap Software Operation
3-4 AP Software Operation Open the file “DVRemoteDesktop.exe”; enter the information of DVR “IP address”, “Port” “Username” and “Password” and click “OK”. You should be able to login DVR successfully and start to use the software. The default username and password is 「admin/ 123456」 “DVRemoteDesktop.exe”... -
Page 38: Chapter 4 Specification
CHAPTER 4 Specifications... - Page 39 APPENDIXⅠ I-DVR.NET REGISTRATION DDNS Registration on I-DVR.NET In the package of each DVR, you will find a sticker shows account information including username and password that allows users to login I-DVR.NET for registration. To register DDNS on I-DVR.NET, please follow the steps as shown. Step 1.
- Page 40 Step 4. Enter DVR →Main Menu → Network Setup → DDNS. Activate DDNS functions and input related information. DDNS work properly when this option selected. This part of the information required and the same within the i-dvr.net Step 5.Back to the i-dvr.net, on this page by pressing "F5: Refresh", IP will be automatically updated into the DVR of the real IP location.
- Page 41 APPENDIXⅡ ez-dns REGISTRATION DDNS Registration on ez-dns.com In addition to I-DVR.NET the Company, the other has a ez-dns.com server may be used.. To register DDNS on ez-dns.com, please follow the steps as shown. Step 1. Please open IE browser and then enter “ ”...
- Page 42 Step 3. The “host.domain” column will show up the setup just entered. Next, enter the DVR the same time setting the DDNS client machine information If DDNS set up at DVR side successfully, the website will update the IP information in 10 minute.
- Page 43 DDNS work properly when this option selected. This part of the information required and the same within the ez-dns.com Step 5.Back to the ez-dns.com, on this page by pressing "F5: Refresh", IP will be automatically updated into the DVR of the real IP location.
-
Page 44: Installation Instruction
APPENDIXⅢ Remote Monitoring IE ActiveX Control Installation Instruction When using IE for remote monitoring for the first time, IE ActiveX Control is needed to be downloaded. 1. When remote monitoring on IE for the first time, an alert message occurs “Install ActiveX control”... - Page 45 4. After installation, IE remote monitoring image appears. 5. If message, “Your security Settings do not allow web sites to use ActiveX controls installed on your computer.” pops on when logging in, please follow the next instruction. 6. First select “Tools” on the tool bar and then select “Internet Options”...
- Page 46 7. Select Security →Trusted Sites → Sites 8. Enter DVR address (This address is only for demonstration. Please use the address depends on the setup of on-site DVR.) into the blanks shown in picture, and then press “add.”...
- Page 47 9. Newly added website will appear at the trusted web sites list. Press close. 10. Go back to IE window, press refresh button or F5.