Related Manuals for Patriot Antenna Rx
Summary of Contents for Patriot Antenna Rx
- Page 1 ANTENNA SYSTEMS 1.8m Offset Rx & TxRx Antenna INSTALLATION & ASSEMBLY INSTRUCTIONS...
- Page 2 IN NO EVENT SHALL PATRIOT ANTENNA BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTER- RUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. In no event shall PATRIOT ANTENNA be liable for damages in an amount greater than the purchase price of the equipment.
-
Page 3: Hardware Table
Thank you for purchasing your Patriot Commercial Antenna. We trust that you will find this to be a well designed product that will provide many years of reliable service. This manual will help you to know the tools and proper installation of the product. Please check, read and understand the content of this manual before beginning your antenna installation. - Page 4 In-Ground Mast Foundation 4 in OD Base plate 18 x 18 x 1/2” Use #4 rebar in all concrete pad sufaces Place nut-washer on this end of all-thread The Optional Kit Includes: Description • 60” Steel Pipe Mast 18x18x1/2” Base plate with 14” centered holes Reinforced Steel Angles for support 3-1/2”...
- Page 5 TXFD - KA/KUR Ku Tx/Rx XPol, Feed Assembly (Optional) TXFD-OMTKUL Ka Tx/Rx CoPol, Feed Assembly (Optional) TXFD-DPLCOPOL/KUL Ka Tx/Rx Linear Pol, Feed Assembly (Optional) TXFD-OMTKAL Ka Tx/Rx Circular Pol, Feed Assembly (Optional) TXFD-OMTPLKA TXPOL-CC C-Band Circular Tx/Rx, Feed Assembly (Optional)
-
Page 6: Mount Assembly
Mount Assembly 1. Place the Pipe Adapter Assembly on to the 4in OD ground pipe, using 1/2” x 1 1/2” bolts. 2. Attach the Az-El Assembly on to the Pipe Adapter Assembly using 1” x 5” bolt, washer, and lockwasher. 3. -
Page 7: Reflector Assembly
Back Frame to Mount assembly 1 . With the help of an assistant, lift the Back Frame assembly and place it onto the Az-El assy as shown. A t tach using 1” x 6” bolt, flat washer, lockwasher and nut. 2 . -
Page 8: Feed Support Assembly
1. Attach Feed Support assy to the lower tube extension of the Back frame using 1/2” x 5 1/2” bolts, nuts and washers. 2. Assemble the Feed holder and Feed Assembly as shown using 1/4” socket head cap screw hardware. Rx Port 1/4” x 1” Caphead with nuts Feed Assembly... - Page 9 Feed Boom Rect. U-Bolt Bkt. 1/4” L. Washer (2) 1/4” Nut (2) THE INFORMATION CONTAINED View shown is for Tx-LHCP, Rx-RHCP. IN THIS DRAWING IS THE SOLE For opposite polarity, rotate OMT 90 deg. PROPERTY OF C-Band Linear Tx/Rx Feed Assembly...
- Page 10 Feed Adjustment (Polarity tuning) 1. Adjust the Feed to the appropriate skew angle using the provided scale reference. NOTE: Refer to the chart below for polarizationangle. Elevation and polarity are both dependent on site azimuth and the differ- ence between satellite and site longitude. Feed Rotation Chart Install site west Install site East...
- Page 11 Windload Information Windload Imposed at 125 mph Force on Front of Dish - 1,790 lbs. Force on Back of Dish- 900 lbs. Overturning moment- 8,950 ft. lbs. Sighting-in Notes- The antenna assembly is now complete. To adjust the antenna toward the selected satellite you must first know its elevation angle above horizon.
-
Page 12: Specifications
Specifications Gain (19.95Rx,29.75Tx) 49.5dBi 53.0dBi Efficiency Noise Temp. (10 degree elev) Cross Polarization -35dB Gain (11.75Rx,14.12Tx) 48.0dBi 49.6dBi Efficiency Noise Temp. (10 degree elev) Cross Polarization -35dB C-Band Gain (3.9Rx,6.1Tx) 38.2dBi 42.5dBi Efficiency Noise Temp. (10 degree elev) Cross Polarization -35dB-LP 17.7dB-CP Mechanical Antenna Size...