Table of Contents
Advertisement
Quick Links
Limited 2 Year Warranty
Fuji Industrial Spray Equipment Ltd. issues a 24
month limited warranty to the purchaser effective from
the date of purchase against defects in materials or
workmanship. This warranty does not cover abuse,
accidental damage, misuse, normal wear parts, motor
brush replacement, or spray gun maintenance and
clean-up. Warranty is void if repairs are made or
attempted by unauthorized persons. At our option,
Fuji Spray will repair or replace defective parts
without charge provided the purchaser return parts
prepaid to the nearest authorized service center or to
the factory.
Factory returns must first receive a Return Material
Authorization. In North America, please call 800-
650-0930 to obtain an authorization number. In other
countries, please call the company where you pur-
chased the product.
This unit is designed to be used for spray painting and
similar operations only. Fuji will not be held liable if
equipment is not used solely for the purpose it was
designed. Warranty will become void through im-
proper installation or operation. Any modifications to
the equipment or deviations from recommended
procedures, accidental damage or any related action
that impairs or abuses normal wear and care of Fuji
spray equipment will also void warranty and liability.
20
CONTENTS
Contents . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Precautions . . . . . . . . . . . . . . . . . 2
Air Control Valve & Diaphragm . . . . . . . 3
Spray pattern . . . . . . . . . . . . . . . . . . . . . . 4
Fan size . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Spraying techniques . . . . . . . . . . . . . . . . 6
Aircap selection . . . . . . . . . . . . . . . . . . . 7
Latex & Viscosity . . . . . . . . . . . . . . . .8 - 9
Viscosity guide . . . . . . . . . . . . . . . . . . . . 9
Cleaning . . . . . . . . . . . . . . . . . . . . . . . 9 -10
Pressure pot use . . . . . . . . . . . . . . . . . .10
Finish Problems . . . . . . . . . . . . . . . . . . 11
Spray Gun Problems . . . . . . . . . . . . . 12 -13
Needle Packing & Seals. . . . . . . . . . . . 14
Parts disassembly . .. . . . . . . . . . . . . . . 15
Turbine problems . . . . . . . . . . . . . . . . . 15
Parts diagrams. . . . . . . . . . . . . . . . . . 16 -18
Gravity Spray Gun. . . . . . . . . . . . . . 18
Service information. . . . . . . . . . . . . . . . 19
Warranty information . . . . . . . . . . . . . . 20
CE Declaration . . . . . . . . . . . Back Cover
1
Advertisement
Table of Contents
Related Manuals for FujiFilm GTX
Summary of Contents for FujiFilm GTX
-
Page 1: Table Of Contents
Limited 2 Year Warranty CONTENTS Fuji Industrial Spray Equipment Ltd. issues a 24 month limited warranty to the purchaser effective from the date of purchase against defects in materials or Contents ......1 workmanship. -
Page 2: Safety Precautions
Please read these instructions carefully before using the equipment For SERVICE & PARTS ELECTRICAL The turbine is powered by a 3-stage or 4-stage (depending on the model) Fuji Spray single speed, bypass, air turbine. This turbine must be connected to the Phone: 800-650-0930 Online: www.hvlp.net correct voltage. -
Page 3: Air Control Valve & Diaphragm
The spraygun can be turned to different angles when spraying, however the cup should never be higher than the gun (above The GTX spraygun is already setup to spray using the pressurized Gravity horizontal). To remove the diaphragm for cleaning, grab the small tab and Cup. -
Page 4: Spray Pattern
CHANGING THE SHAPE OF THE FAN Turn the aircap 8002 until it clicks into the horizontal position. This setting produces a vertical fan useful for spraying from side to side. Then set the aircap in a vertical position. This setting produces a horizontal fan, useful for spraying up and down. -
Page 5: Fan Size
To change the size of the fan you will turn the collar 8001 clockwise or The Fuji XT-2 & GT-X2 Spraygun counter-clockwise. Winding the collar IN results in a LARGER FAN. Winding the collar OUT will result in a SMALLER FAN. The standard position is shown in Fig A. -
Page 6: Spraying Techniques
ACTUAL SPRAYING TECHNIQUES. INSTALLING THE SPRING PLATE The spraygun should be held perpendicular to the surface at all times. If the spring plate 2027 is installed upside down, the aircap will not click HOLD THE GUN NO MORE THAN 8” (20cm) AWAY FROM THE SURFACE into position when turned. -
Page 7: Aircap Selection
ADJUSTING THE NEEDLE PACKING AIRCAP SET SELECTION Like all spraygun manufacturers, we use ‘stock’ stainless steel rod for the The fluid nozzle 8004 and needle 8020 MUST always match exactly. Size needle. This rod can differ in diameter slightly with each production run. So No.4 is standard with all Fuji sprayguns. -
Page 8: Latex & Viscosity
A WORD ABOUT LATEX (EMULSION) PAINT THE TRIGGER IS SLUGGISH Although latex house paint was never originally intended to be sprayed, a • The needle packing is too tight - see ADJUSTING THE NEEDLE professional finish can be achieved by following a few simple rules. PACKING. -
Page 9: Viscosity Guide
VISCOSITY GUIDE SPRAYGUN PROBLEMS To test the viscosity of the paint material, fill the viscosity cup to the brim NO PAINT (OR VERY LITTLE PAINT) and time how long it takes for the liquid to empty out through the hole. We recommend you experiment to find the ideal viscosity for your application THIS IS THE MOST COMMON PROBLEM ENCOUNTERED - and record the information for the next time. -
Page 10: Pressure Pot Use
If this type of cleaning is done while the paint is still wet in the gun, it FINISH PROBLEMS should be all that is necessary to keep the gun clean enough for next time. Do not leave liquids in the cup overnight or for long periods. The Gravity ORANGE PEEL - If the finish is rough and resembles orange peel then the Gun can be cleaned without hooking up to the hose.
Need help?
Do you have a question about the GTX and is the answer not in the manual?
Questions and answers