CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Product Description 3‐Axis Indoor Mini IR Dome Congratulations on your purchase of this product. This analog surveillance dome features advanced functions in a compact body and is suited for tight, indoor environments such as a corridor or elevator. The camera utilizes advanced Sony image sensor technology producing high definition, realistic color. Features Indoor plastic mini dome housing Infrared LEDs for night vision 3‐Axis bracket for versatile positioning of the lens On‐Screen Display (OSD) menu controlled by cable button Low Light Illumination, Sense‐UP, Digital Wide Dynamic Range (WDR), 3D Noise Reduction (3DNR) 12V DC Models Model Number Resolution Lens Features ELI‐EDC‐65‐312IR 650 TVL 2.8~12mm Varifocal Infrared Safety Information Read these instructions. Heed all warnings. Follow all instructions. Clean only with dry cloth. Do not block any ventilation openings. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers) that produce heat. Only use attachments/accessories specified by the manufacturer. Pay attention to the power requirements. ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub‐Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. Reorient the antenna of the radio/TV experiencing the interference. Relocate the equipment with respect to the radio/TV. Move the equipment away from the radio/TV. Plug the equipment into an outlet on a different electrical circuit from the radio/TV experiencing the interference. If necessary, consult your local dealer for additional suggestions. NOTE: Modifications to this product will void the user’s authority to operate this equipment. Product Components Box Contents Dome Camera Quick Start User Guide Additional Materials Needed for Installation Minimum of 3 mounting screws and if necessary, drywall anchors Tape for protecting connections Power supply 12VDC 350mA ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Product Diagrams Plastic Housing Infrared LEDs Lens Plastic Dome Installation Mounting This is an indoor camera. It is not suitable for exposure to particles or liquids. 1. Unscrew the mounting base from the camera by twisting counter‐clockwise. Use this base as a guide to mark the locations for screw and cable management holes on the mounting surface. Make note of the arrow on the base indicating the front of the camera. There are 2 options for the cable management hole – at the back of the camera base or in the center of the camera base. 2. Drill a starter hole at each marked location. Drill a cable management hole at least 14mm in diameter to permit the camera’s cable to be inserted through the mounting surface. 3. If necessary, insert drywall anchors into the screw holes. 4. Place the camera base into location. Insert a screw through each of the screw holes in the base and into the mounting surface and then tighten each screw until the base is secure. 5. Feed the camera’s cable through the access hole; position the dome onto the mounted base, and twist clockwise to secure. Page | 5 ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Caution: Once power is supplied, do not remove the camera from the mounting base due to risk of electrical shock. Connections 1. Use a BNC connector to connect the camera’s VIDEO OUT to the monitor’s (or DVRs) VIDEO IN. Use the following recommendations for cable types and distances: Maximum Cable Length Type of Coaxial Cable RG‐59/U RG‐6/U RG‐11/U RG‐15/U Recommended Max 250 M 500 M 600 M 800 M Cable Length 825 ft 1650 ft 1980 ft 2640 ft 2. The power is DC 12V (+/‐ 10%) / 350mA. Use the following recommendations for cable types and distances: 12V DC Recommended Wire Size and Resistance (68°F) Copper Wire Size #24 #22 #20 #18 (AWG) (0.22 mm ) (0.33 mm ) (0.52 mm ) ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Adjusting the Camera 1. To adjust the camera angle, remove the white casing and dome by pressing on the latch release indicated by the arrow, and prying off the casing. The first time you remove the casing, it may be a little tight. 2. The camera lens can be moved by twisting the black shell inside the white base. The camera module inside the black shell can be moved up and down. There is no need to remove any screws or to attempt to disassemble the camera. 3. To replace casing, align the arrow with the latch release and press on. Focusing Focus Control Zoom Control 1. Focusing the camera is done by adjusting the two screws just above the lens. 2. The screw on the left will adjust the lens focus. 3. The screw on the right will adjust the lens zoom. 4. Focus to the depth of field that is most important. Page | 7 ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com On‐Screen Display (OSD) Settings On the OSD control device on the cable, hit the center button to activate the OSD settings. The menu as below will appear. Use the button by moving up/down/left/right and depressing as ‘Enter’ to change OSD settings. For further definition of each setting see the eLine web site under Support. http://www.elinetechnology.com. Lens ELC DC Exposure HBLC D‐WDR BLC HLI/D‐WDR AGC OFF LOW MIDDLE HIGH 3D DNR OFF LOW MIDDLE HIGH SENSE‐UP AUTO OFF X2 X4 X8 X16 X32 X64 X128 X256 X512 EXIT COLOR WB MODE ATW MANUAL AWC>PUSH AWC R‐Y‐GAIN O‐256 B‐Y‐GAIN 0‐256 EXIT DAY & NIGHT D&N MODE AUTO COLOR B&W EXT FUNCTION MIRROR ON OFF SHARPNESS 0‐30 ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Specifications Feature Specification Minimum Illumination 0.001 Lux / 0 Lux (with IR LED ON) S/N Ratio More than 50dB Scanning System 2:1 Interface Synchronous System Internal, Negative sync Auto Electronic Shutter NTSC: 1/60s~1/100,000s / PAL: 1/50s~1/100,000s Gamma Characteristic 0.45 IR Distance 20 Meters (with ȼ5x21 pcs Infrared LED) Video Output 1Vpp. 75Ω Auto Gain Control Auto Power/Current DC 12V (+/‐10%) 350mA Dimension ȼ127 x 95(H) mm Weight 520g Storage Temperature ‐30°~60°C RH 95% Max Operating Temperature ‐10°~45°C RH 95% Max Troubleshooting No picture after providing power Check the power connection to the power supply to the power outlet for connectivity. ...
CAMERA ELI‐EDC USER MANUAL eLineTechnology.com Warranty Repair/Replacements Subject to the terms of the limited warranty in effect at the time of purchase, e‐Line will repair or replace a product that fails to meet the terms provided, within the product’s warranty period. eLine reserves the right to replace any product under warranty with new, refurbished or remanufactured product. For product purchased directly from eLine by a dealer or an integrator, the warranty period starts from either a) the date of shipment from eLine ’s facility (point of origin) or b) the manufacturer’s date code (if the shipment date is unknown). Except for software products (which shall be treated as if purchased directly e‐Line for purposes of determining the start of the warranty period as set forth in the immediately preceding sentence), for product purchased from an authorized eLine distributor by a dealer or an integrator, the warranty period starts from the date the product is purchased by the dealer or integrator. Warranty periods vary based on product category and type of equipment, as shown in Table 1 entitled “Product Warranty Periods” below. We will return equipment or ship replacement equipment via the same incoming ship method at no additional charge. If you request a different return ship method, we will charge for the full shipping cost. Product Warranty Periods Table 1 lists warranty durations for most eLine equipment, sorted by category. Warranty periods start as set forth under the heading “Warranty Repair/Replacements” above. For items that do not appear in Table 1, contact Customer Service or your sales rep for the applicable policy. Product Type Product Warranty Exceptions eLine Cloud Cameras 2 years PTZ Cameras – 1 year Other eLine 2 years ‐‐‐‐ For help or more information on setup, please visit http://elinetechnology.com Or contact eLine support provided by 2D Electronics at 303.938.1133 support@2delectronics.com eLine, 1070 W 124th Ave Suite B‐100, Westminster, CO 80234 Page | 10 ...