Download Print this page

Advertisement

�����������
����������������������������������������������
��������������������������������������������������
���������������������������������������������������������������
����������������������������������������������������������������
n PRIMERGY BX600 Manuals
Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.
[CD-ROM Drive] :\MANUAL\INDEX.PDF
Manuals can be displayed using Acrobat
*This manual corresponds with BX600 S3 Blade Server System Unit and BX620 S4 Server Blade. For chassis and server blades not described in
this guide, refer to the corresponding manual on the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
1
Checking the items
supplied
Check the contents in the package using
the "Contents List".
If any items are missing, inform an office listed in
the "Contact Information".
3
Checking location before installing the server
For details on installing the rack, refer to the "Installation Guide for the RACK" and manuals provided with the rack.
nConditions
When installing this server avoid the following areas.
- Humid, dusty, or oily areas
- Poorly ventilated areas
- Areas close to fire or other sources of heat
- Areas close to water
- Areas close to direct sunlight or near heating appliances
- Areas with a temperature of below 10°C or above 35°C
- Areas with humidity of less than 20% or more than 80%
- Salty areas
- Areas where corrosive gas is generated
- Areas where cables become trip hazards
- Areas where strong magnetic fields are generated, such as near TVs and speakers
- Areas where the device is not stable and could tip over and hurt somebody
-
In dusty areas, dust will quickly stick to the front and backside of the server. Since this can cause failure, changing the
installation place is recommended.
-
Be sure to secure the rack with stabilizers to prevent the device from tipping over.
BX600
Reader
or Adobe
Reader
®
®
®
1
. If using Acrobat
Reader
, use version 5.0 or later.
®
®
®
2
Reading and understand-
ing "Safety Precautions"
Before using this server, be sure to read and un-
derstand the attached "Safety Precautions".
Also check it when connecting, installing internal options
and setting up this server.
B7FH-4871-01EN-00

Advertisement

   Summary of Contents for Fujitsu Primergy BX600

  • Page 1

    ® *This manual corresponds with BX600 S3 Blade Server System Unit and BX620 S4 Server Blade. For chassis and server blades not described in this guide, refer to the corresponding manual on the Fujitsu PRIMERGY website (http://primergy.fujitsu.com). Checking the items...

  • Page 2

    nInstalling the server to the rack When installing or removing the server, please contact an Secure the chassis and rack. office listed in the "Contact Information". Open the front and rear doors of the rack. Align rail with the length of the rack, and temporarily fasten the rack using �����������...

  • Page 3: Installing Internal Options

    Installing internal options If internal options have been purchased separately, install them before installing the operating system. Install the non-system hard disk unit after the OS has In the following case, do not install internal options now. been installed. Installing the OS after the hard disk unit - Custom Made Service has been installed may end in an error.

  • Page 4: Connecting Peripheral Devices

    Connecting peripheral devices Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following order. ���������������������� ����������������� ��������������������� ��������� ��������� ���������� ������� ����������� ������������ ��������������� ��������� ���������������������� �������������������� �� ������������ ������������� ������������� - Use a power cable that meets your country's standard. - Connect cables with enough allowance for operation while the device is pulled out from the rack.

  • Page 5

    nConnecting floppy disk drives/CD-ROM (or DVD-ROM) drives For this server, floppy disk drives including USB interface and CD-ROM drives (or DVD-ROM drives) can be con- nected to the server blade using USB Cables. When connecting CD-ROM drives, Connect the floppy disk drive or CD- plug the power cable of the CD-ROM ROM drive to the USB Cable.

  • Page 6: Bios Setup Utility

    [F2] while the message is being values of the BIOS Setup Utility in the Configuration " Sheets that is available from Fujitsu PRIMERGY website displayed. (http://primergy.fujitsu.com). 2. Check/change the BIOS settings. 3. Select "Save Changes & Exit" from the Exit Prepare the ServerStart CD-ROM.

  • Page 7: Installing The Os

    Installing the OS This section explains the procedures to install the OS using ServerStart. For details about OS installation procedures without using ServerStart, refer to the "User's Guide". ������������ "Chapter 4 Manual OS Installation" Insert the ServerStart floppy disk Click [Start here to create a complete supplied with this server, and click configuration file].

  • Page 8

    BIOS Setup Utility as required. floppy disk drive or CD-ROM drive. For details about setting procedures, refer to "PRIMERGY BX600 LAN Switch Blade Document CD", Exit the operating system (OS). "User's Guide Chapter 8 Hardware Configuration/ After the OS is exited, the server is automatically Utilities", or the option’s manual.

  • Page 9: Support And Service

    The latest PRIMERGY, Update module, driver, and soft- advance. ware information is available at the address below. Use as Print the "Configuration Sheets"- "Accident sheet" that necessary. is available from Fujitsu PRIMERGY website (http:// http://primergy.fujitsu.com primergy.fujitsu.com) and enter the confirmed information. lBefore requesting repairs lNon-durable components If an error occurs in this server, refer to "User's Guide 9.2...

  • Page 10: Contact Information

    Tel: +60-3-8318-3700 Tel: +1-800-831-3183 Fax: +60-3-8318-8700 Fax: +1-408-496-0575 Address: 1st Floor, No.3505 Jalan Technokrat 5 Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470 63000 Cyberjaya, Selangor Darul Ehsan Malaysia For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).

  • Page 11

    It is the customer's responsibility to maintain backup copies in advance. In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items covered under warranty.

Comments to this Manuals

Symbols: 0
Latest comments: